Miele PW 6163 EL/D User manual

10.11 M.-Nr. 07 542 090 / 05

Installation plan

Washer

Installatietekening

Wasautomaat

PW 6163 EL/D

en - GB

nl - NL

M.-Nr. 07 542 090 / 05

Installationsplan / Installation plan: PW 6163 EL/D

Datum / Date: 16.03.2011 Seite / Page: 9

Technical datasheet

Washer-extractor:

Heating:

PW 6163

Electric /

Steam

Legend:

Abbreviations in bold type:

Connection required

en-GB

Abbreviations in circle with dashes:

Connection optional or required depending on model

version

Optional extras:

BWS

Conversion kit

Steam and

foam discharge

Vapour discharge on site (int. diameter)

110 [DN 100

connection]

Foam discharge connection on site (ext. diameter)

110 [DN 100]

Drainage must be provided for condensate.

Alternatively, the foam pipe can be passed through

the machine to the machine drain.

ISA

Integrated

foam line

Pipework

50 [DN 50

connection]

Opening in machine casing (diameter)

63.5

MSG

Additional Miele

fan

Standard voltage

1N AC 230

Frequency

Rated load

0.03

Max. air throughput

m³/h

150

Max. pressure gradient

170

Sound power level

dB (A)

DAV

Steam

connection

valve

The following electric steam valve and pneumatic

steam valve can be ordered separately.

Electric steam valve (ELD 01)

Regulatable steam pressure

kPa

200 - 1000

Connection gauge

Inch

½“

Voltage

1N AC 230

Pneumatic steam valve (PND)

Regulatable steam pressure

kPa

0 - 1000

Connection gauge

Inch

½“

The steam connection valve to regulate the steam

supply must be provided on site.

Miele plinth

Box plinth

Height

170

Width

1110

Depth

870

Weighing

system

Plinth with integrated weighing system

Height

170

Width

1110

Depth

870

Machine should not be subject to external loads or

weights when using weighing system.

Temporary or static loads on casing may prevent the

calibration of the weighing cells and impair the proper

functioning of the weighing system.

All supply connections including steam supply must

be flexible on machines with weighing system.

Installationsplan / Installation plan: PW 6163 EL/D

Datum / Date: 16.03.2011 Seite / Page: 10

Machine connections:

Electrical

connection

1. Standard voltage (as supplied)

3N AC 380-415

Frequency

50 - 60

Rated load

18.0

Fuse rating

3 × 25

Connection cable (to be ordered

separately)

Minimum cross-sectional area

mm²

5 × 4

with threaded cable connector

M 32 x 1.5

Deviations herefrom:

2. Standard voltage (as supplied)

3 AC 220-240

Frequency

50 - 60

Rated load

18.0

Fuse rating

3 × 50

Connection cable (to be ordered

separately)

Minimum cross-sectional area

mm²

4 × 10

with threaded cable connector

M 40 x 1.5

Alternative voltage

Convertible

3 AC 208

Frequency

Rated load

15.3

Fuse rating

3 × 50

Connection cable (to be ordered

separately)

Minimum cross-sectional area

mm²

4 × 10

with threaded cable connector

M 40 x 1.5

Connection using multi-pole wall socket in compliance

with IEC 60309 and IEC 60947 is recommended in

order to simplify electrical tests.

Install mains isolator according to IEC 60947 on hard-

wired connection. Wall socket or mains isolator must

be accessible after installation.

The use of an earth leakage circuit breaker (ELCB) is

strongly recommended. A type B RCD (residual

current device) must then be used.

If necessary, equipotential bonding with good

galvanic contact must be provided in accordance with

all appropriate national and local regulations.

Steam

connection

(Steam direct)

Steam pressure

kPa

≤ 400

Boiling point

°C

≤ 152

Heater rating

Volume flow

kg/h

Connection thread (on site)

Inch

½" internal thread

Steam valve, steam filter, steam stopcock and non-

return valve must be provided on site.

Note installation instructions for steam-heated Miele

washer-extractors.

Cold water

(Soft water)

Min. flow pressure

kPa

100

Max. pressure

kPa

1000

Volume flow necessary

l/min

Max. volume stream in absence of hot and raw water

supplies.

l/min

79.5

Special version, unit without detergent dispenser.

Volume flow necessary

l/min

Max. throughput (if hot and raw water supply is

not available)

l/min

77.5

On-site connection thread according to DIN 44 991

Inch

1" external thread

Length of supply hose

1500

(supplied: 2 connection hoses + Y piece)

Water requirements with standard connection to hot

water in 60°C programme ( average value)

l/h

not yet available

In the absence of a hot water supply, connect to

alternative supply.

In the absence of a raw water supply, connect to

alternative supply.

Table of contents

Languages:

Other Miele Washer manuals

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual