Miele PT 7251 EL User manual

Table of contents

Other Miele Washer manuals

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG

LG TV2516DV3B owner's manual

LG

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual

Installationsplan / Installation plan

Installatietekening

Plan d`installation

Pianta di installazione

Plano de instalación

Plano de instalação

Σχέδιο εγκατάστασης

Asennusohje

Installasjonsplan

Installationsplan G

PT 7251 EL

Materialnummer / Mat. no.: 06 478 800

Änderungsstand / Version: 00

Datum Zeichnung / Drawing date: 23.09.2004

Datum Legende / Legend date: 23.09.2004

Installationsplan PT 7251 EL

Stand: 23.09.2004 Seite 7

Technical datasheet

Tumble dryer:

Heating:

PT 7251

Electric (EL)

Legend:

Circled, bold-type abbreviations:

Connection required

Abbreviations surrounded by broken circle:

Connection optional or required, depending on model

G

Optional extras:

Concrete plinth (to be provided on-site) optional.

Min. concrete quality B15

BS Concrete platform

Recommended height mm 50

Minimum height mm 50

Recommended width mm 900

Recommended depth mm 850

Ensure good anchorage!

Machine connections:

1. Standard voltage (as supplied) V 3N AC 380-415

Frequency Hz 50 (60)

Electrical

connection

Rated load kW 14.2

Fuse rating A 3 × 25

Supply lead (H 07 RN-F), min. cross-section mm² 5 × 4

with threaded cable connector M 32

2. Standard voltage (as supplied) V 3 AC 220-240

Frequency Hz 50 (60)

Rated load kW 14.2

Fuse rating A 3 × 50

Supply lead (H 07 RN-F), min. cross-section mm² 4 × 10

with threaded cable connector M 40

3. Standard voltage (as supplied) V 3 AC 440

Frequency Hz 50 (60)

Rated load kW 14.2

Fuse rating A 3 × 25

Supply lead (H 07 RN-F), min. cross-section mm² 4 × 4

with threaded cable connector M 32

Connection using multi-pole wall socket in compliance with

IEC 60309 and IEC 60947 is recommended in order to

simplify electrical tests.

If using a hard-wired connection, install mains isolator

according to IEC 60947.

Wall socket or mains isolator must be accessible after

installation.

The use of an earth leakage circuit breaker (ELCB) is strongly

recommended.

If necessary, equipotential bonding with good galvanic contact

must be provided in accordance with all appropriate national

and local regulations.

Connection cable, min. cross-section mm² 3 × 1.5Peak load

management Input leads should not be in direct contact with any source of

heat.

Signal supplied via potential-free (galvanically separated)

contact.

Installationsplan PT 7251 EL

Stand: 23.09.2004 Seite 8

Nominal air throughput in vented mode m³/h 510Vented

Permissible pressure attenuation Pa 200

Machine vent connection (da× s × l) [DN 150] mm 150 × 0.6 × 78

On-site vent connection (interior diameter) mm 150

Max. temperature °C 80

As relative humidity can be as high as 100%, suitable

measures must be taken to prevent a backflow of condensate

into the machine.

If the machine fan is unable to transport air over the on-site

vent ducting distance, an additional fan with a suitable

capacity must be installed either in the ducting or at the point

of discharge to atmosphere.

Standard connection:

=> Air intake from installation site

Air intake

Direct air intake recommended cm² 531

(to prevent draughts)

Sufficient air intake should be available to replace the

displaced volume of air.

Alternative connection: (cf. Detail Y)

=> Direct air intake

Machine connection (di × s × l) [NW160] mm 161 × 4.0 × 16

On-site connection (external diameter) mm 160

Lid removal exposes live components! For safety reasons,

the pipe connected for central air intake should be at least

900 mm long and secured using two screws.

2 × screws DIN 571 (Ø × length) mm 6 × 40

2 × rawl plugs (Ø × length) mm 10 × 50

Fittings (supplied)

The machine should be bolted to the floor.

Fixing materials for floating screed floor to be provided on site

Machine data Width mm 900

Depth mm 836

Height mm 1400

Knocked-down dimensions (W × H) mm 900 x 1500

Rear wall gap (measured to front of machine) mm 1100

Net weight kg 160

Dynamic floor load, max. N 1716

Average heat dissipation

(dependent on ambient room temperature and programme

selected)

W 500

Acoustic power level (re1 pW) dB (A) 68

Sound pressure level dB (A) not yet available

(measured at a distance of 1 m from the machine and at a

height of 1.6 m)

Installation should only be carried out by authorised fitters in accordance with valid regulations!

Observe installation instructions when installing machine! All rights reserved!