Miele DA250-4 User manual

Installation Instructions

DA 250-4 en-CA

Installation, repair and maintenance work should be performed by

a Miele authorized service technician in accordance with national

and local safety regulations and the provided installation instructions.

The ceiling mounting plate will

support the weight of the hood. This

ceiling plate must be attached to

rigid structural framing that is

supported in its entirety by the

ceiling joists, or to the ceiling joists

directly. Do not attach the plate

directly to the ceiling with anchors,

toggle bolts, etc.

Structural support

All electrical work should be

performed by a qualified electrician

in strict accordance with national

and local safety regulations.

Installation, repairs and other work

by unqualified persons could be

dangerous. The manufacturer can

not be held responsible for

unauthorized work.

Ensure that power to the appliance

is OFF while installation or repair

work is performed.

Verify that the voltage, load and circuit

rating information found on the data

plate (located behind the grease filter),

match the household electrical supply

before installing the hood.

If there is any question concerning the

electrical connection of this appliance

to your power supply, please consult a

licensed electrician or call Miele’s

Technical Service Department. See

back cover for contact information.

WARNING:

THIS APPLIANCE MUST BE

GROUNDED

Important

To increase security before the

machine is installed, it is

recommended to install a protective

switch (30 mA).

Important

The hood must be hard wired

accordingly:

Black/Red wire:. . . . connect to L1 (live)

White wire: . . . . . connect to N (neutral)

Green wire: . . connect to GND (ground)

Maximum load. . . . . . . . . . . . . . . 430 W

Fan. . . . . . . . . . . . . . . . . . . . . . . 350 W

Lighting . . . . . . . . . . . . . . . . . 4 x 20 W

Voltage . . . . . . . . . . . . . . . . . . . . . 120 V

Frequency . . . . . . . . . . . . . . . . . . 60 Hz

Circuit rating. . . . . . . . . . . . . . . . . . 15 A

Electrical data

Exhaust connection 6" (150 mm) diameter

1) Entrance for ductwork and power cord

Appliance dimensions

Do not install this exhaust hood over

cooktops burning solid fuel.

Provided a larger distance is not

given by the manufacturer of the

cooktop, follow the minimum safety

distances between a cooktop and

the bottom of the hood:

- 22" (550 mm) above electric

cooktops,

- 30" (762 mm) above gas cooktops,

- 26" (650 mm) above an open

electric grill or an open electric

boiler/fryer.

If there is more than one appliance

beneath the hood and they have

different minimum safety distances

always select the greater distance.

Observe local building codes.

See "Important Safety Instructions"

for further information.

CAUTION:

During the installation process,

please be careful of sharp edges

that can cause harm.

Installation

Installation instructions

^See the enclosed installation

instruction sheet.

^Please read the "Important Safety

Instructions" and Installation

instructions before installing this

hood.

Installation accessories

4 Screws 8 x 60 mm with

4 Washers

for securing the ceiling plate.

(S8 wall anchors included in the

packaging are not for use in USA)

2 Screws M 4 x 8 mm

for adjusting the chimney.

4 leveling plates

for correcting an uneven ceiling.

1 exhaust connector

1 hose clip for securing the ducting.

Installation

,WARNING

Danger of toxic fumes.

Gas cooking appliances release

carbon monoxide that can be

harmful or fatal if inhaled.

The exhaust gases extracted by

the hood should be vented

outside of the building only.

Do not terminate the exhaust

ducts in attics, garages,

crawlspaces, etc.

To reduce the risk of fire, only use

metal ductwork.

Please read and follow the

"IMPORTANT SAFETY

INSTRUCTIONS" to reduce the risk of

personal injury. Follow all local building

codes when installing the hood.

Exhaust ducting and connections

– The ducting should be as short and

straight as possible, and the number

of sharp bends should be minimized.

– For most efficient air extraction, the

diameter of the ductwork should not

be less than 6" (150 mm). Use of flat

ducts also reduces the air extraction

efficiency.

– Noise levels of the hood will increase

if flat ducts or round ducts of less

than 6" (150 mm) in diameter are

used.

– Use smooth or flexible pipes made

from approved non-flammable

materials for exhaust ducting.

– Where the ductwork is horizontal, it

must slope away from the hood at

least 1/8" per foot (1 cm per meter) to

prevent condensation dripping into

the appliance.

– If the exhaust is ducted through an

outside wall, a Miele Telescopic Wall

Vent can be used.

Air extraction

– If the exhaust is ducted into an

inactive flue, the air must be expelled

parallel to the flow direction of the

flue.

Never connect an exhaust hood to

an active chimney, dryer vent, flue,

or room venting ductwork. Seek

professional advice before

connecting an exhaust hood vent to

an existing, inactive chimney or vent

flue.

Important

If the ductwork runs through rooms,

ceilings, garages, etc. where

temperature variations exist, it may

need to be insulated to reduce

condensation.

Condensate trap

optional accessory

In some cases, a condensate trap may

be required to collect and evaporate

any condensation which may develop.

This optional accessory is available for

ducts 5" (125 mm) and 5 7/8" (150 mm)

in diameter.

^When installing a condensate trap,

ensure that it is positioned vertically

and if possible directly above the

exhaust outlet.

Air extraction

Alteration rights reserved / 3306 M.-Nr. 06 850 870 / 00

en-US

Other manuals for DA250-4

Table of contents

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual

Nibe

Nibe S Series Installer manual

Caple

Caple CCH100 technical information