Miele KM 469 User manual

Installation instructions

Ceramic hobs

KM 460 / KM 461 / KM 463

KM 464 / KM 465 / KM 466

KM 468 / KM 469

To avoid the risk of accidents

or damage to the machine

it is essential to read these

instructions before it is installed

or used for the first time.

GiZHWOr

M.-Nr. 05 397 194

Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety distance above the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation of appliance on wall with additional niche cladding . . . . . . . . . . . . . . . 5

Appliance dimensions and worktop cut-out . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KM 460 / KM 461 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KM 463. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

KM 464. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KM 465 / KM 466 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

KM 468. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

KM 469. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fitting the spring clamps and safety brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installing the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Granite worktops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installing the appliance in granite worktops. . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Electrical connection AUS/NZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Contents

Installation

Fit wall units and extractor hood be-

fore fitting the hob, to avoid damag-

ing the ceramic surface.

The veneer or laminate coating of

worktops (or adjacent kitchen

units) must be treated with 100°C

heat-resistant adhesive which will not

dissolve or distort.

Any backmoulds must be of heat-resis-

tant material.

Ideally the hob should be installed

with plenty of space on either side.

There may be a wall at the rear and a

tall unit or wall at one side. On the other

side, however, no unit or divider should

stand higher than the hob (see illustra-

tions).

This equipment is not designed for

maritime use or for use in mobile

installations such as caravans, aircraft

etc. However it may be suitable for

such usage subject to a risk assess-

ment of the installation being carried

out by a suitably qualified engineer.

aMinimum distance between

cut-out and tall unit/wall = 50 mm,

unless they are made from a

non-combustible material.

See: Installation of appliance on

wall with additional niche cladding.

recommended

possible, but not recommended

not allowed

Safety instructions

Spray canisters, aerosols and other

inflammable substances should not

be stored in a drawer under the hob un-

less there is a shelf separating the

drawer from the hob. If cutlery inserts

are to be placed in the drawer, these

must be made of a suitable heat-resis-

tant material.

The hob may not be built in over a

fridge, fridge-freezer, freezer, dish-

washer, washing machine or tumble

dryer.

After installing the hob, ensure that

the connection cable cannot come

into contact with the underside of the

appliance. Make sure that there is no

mechanical obstruction, such as a

drawer, which could damage it.

Keep these instructions in a safe place

and pass them on to any future owner

of the appliance.

All dimensions in this instruction booklet

are given in mm.

Safety distance above the

appliance

bA minimum safety distance must be

maintained between the hob and a

cooker hood above it. See the manu-

facturer’s operating and installation

instructions for details. For any flam-

mable objects, e.g. utensil rails etc. a

minimum safety distance of 760 mm

should be maintained between it and

the hob below.

When two or more appliances are in-

stalled together below a cooker

hood, e.g. an electric hob and a gas

wok combiset, which have different

safety distances given in their instal-

lation instructions you should select

the greater distance of the two.

Safety instructions

Installation of appliance on wall with additional niche cladding

Hob with frame/bevel edge lush fit hob

aMasonry

bNiche cladding

cUpstand

dWorktop

eWorktop cut-out

f50 mm minimum distance between niche cladding and the worktop cut-out.

This distance is only necessary for niche cladding made of wood or any other

combustible material. For non-combustible materials (metal, ceramic tiles or

similar), this dimension can be reduced by the thickness of the niche cladding

material. The materials can warp or distort when subjected to high tempera-

tures.

Safety instructions

min. 50

KM 460 / KM 461

aSpring clamps

^Make the worktop cut-out following

the dimensions shown above.

^Remember to maintain a minimum

safety distance of 50 mm between

the hob and the back wall and a side

wall to the right or left of the hob. See

"Warning and Safety instructions".

^Seal the cut surfaces with a suitable

sealant to avoid swelling caused by

moisture.

The materials used must be heat re-

sistant.

bDepth for building in including the

electrical connection box located at

the rear on the right hand side

approx. 48 mm.

If during installation the corners of

the frame are not flush with the

worktop surface, the corner radius,

Max R4 can be carefully scribed to

suit.

Appliance dimensions and worktop cut-out

KM 463

aSpring clamps

^Make the worktop cut-out following

the dimensions shown above.

^Remember to maintain a minimum

safety distance of 50 mm between

the hob and the back wall and a side

wall to the right or left of the hob. See

"Warning and Safety instructions".

^Seal the cut surfaces with a suitable

sealant to avoid swelling caused by

moisture.

The materials used must be heat re-

sistant.

bDepth for building in including the

electrical connection box located at

the rear on the right hand side

approx. 48 mm.

If during installation the corners of

the frame are not flush with the

worktop surface, the corner radius,

Max R4 can be carefully scribed to

suit.

Appliance dimensions and worktop cut-out

KM 464

aSpring clamps

bDepth for building in including the

electrical connection box located at

the rear on the right hand side

approx. 51 mm.

cHeight above worktop

eSafety bracket

^Make the worktop cut-out following

the dimensions shown above.

^Remember to maintain a minimum

safety distance of 50 mm between

the hob and the back wall and a side

wall to the right or left of the hob. See

"Warning and Safety instructions".

^Seal the cut surfaces with a suitable

sealant to avoid swelling caused by

moisture.

The materials used must be heat re-

sistant.

Appliance dimensions and worktop cut-out

560

490

max.R4

min.50

590

520

75 75

Protective base

^A protective base must be installed

underneath the hob. There must be a

gap of at least 15 mm between the

hob and the base (see illustration).

If during installation the corners of

the frame are not flush with the

worktop surface, the corner radius,

Max R4 can be carefully scribed to

suit.

Appliance dimensions and worktop cut-out

min.

KM 465 / KM 466

aSpring clamps

^Make the worktop cut-out following

the dimensions shown above.

^Remember to maintain a minimum

safety distance of 50 mm between

the hob and the back wall and a side

wall to the right or left of the hob. See

"Warning and Safety instructions".

^Seal the cut surfaces with a suitable

sealant to avoid swelling caused by

moisture.

The materials used must be heat re-

sistant.

bDepth for building in including the

electrical connection box located at

the rear on the right hand side

approx. 53 mm.

If during installation the corners of

the frame are not flush with the

worktop surface, the corner radius,

Max R4 can be carefully scribed to

suit.

Appliance dimensions and worktop cut-out

Other manuals for KM 469

Table of contents

Popular Hob manuals by other brands

Siemens

Siemens EX875KYV1E INFORMATION FOR USE

AEG

AEG CERAMIC HOB 6010 K Installation and operating instructions

VALERA

VALERA CT 70A datasheet

Zanussi

Zanussi ZGF 6420 Instruction booklet

Gaggenau

Gaggenau CI 273 use and care manual

G3 Ferrari

G3 Ferrari Energy user manual

Pkm

Pkm IN4B instruction manual

Award

Award H903BG user manual

Zanussi

Zanussi VCH 5005 RZ Instruction booklet

Hotpoint

Hotpoint IS67V8CCXT/E manual

AEG

AEG HK854870XB user manual

Cookology

Cookology SEP600BK instruction manual

Bauknecht

Bauknecht Hob Instructions for use

Zanussi

Zanussi ZGM 782 Instruction booklet

dipo INDUCTION

dipo INDUCTION DIBK218S quick start guide

Blomberg

Blomberg MKN 24201 W user manual

Progress

Progress PAI3101F user manual

Hotpoint Ariston

Hotpoint Ariston PKL 641 IX/HA operating instructions