Midea NYERF User manual

OWNER’S MANUAL

OIL FILLED HEATER

MODEL:NYERF

READ AND SAVE THESE INSTRUCTIONS

Attention: Pictures in the IM are for reference only.

GD Midea Environment Appliances MFG.Co.,Ltd.

No.28, Dong Fu Road, Hesui East Industrial Area, Dong Feng Town,

Zhongshan, Guangdong 528425 P.R.China

145X210MM

IMPORTANT SAFEGUARDS

When using any electrical appliance, basic precautions

should always be followed to reduce the risk of fire,

electrical shock and injury to persons , including the

following:

1. Read all instructions before using heater.

2. This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials

such as furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (0.9m) from the heater. Allow

heater to cool before moving and then use the built-in

handle for easy movement.

3. Extreme caution is necessary when heater is used by or

near children and whenever heater is left unattended.

4. Always unplug the heater when it is not in use.

5. Do not operate any heater with a damaged cord or plug,

or after the heater malfunctions, or has been dropped or

damaged in any manner. Return heater to the

manufacturer for examination, electrical or mechanical

adjustment, or repair.

6. Do not use heater outdoors. This product is intended for

normal household indoor use only.

7. This heater is not intended for use in bathrooms, laundry

areas or similar moist indoor locations. Never locate

heater where it may fall into a bathtub or other water

container.

8. Do not run power cord under carpeting. Do not cover

cord with throw rugs, runners or the like. Arrange cord

away from traffic areas and where it will not be tripped

over.

9. To disconnect heater, set controls to OFF, then remove

plug from outlet.

10. Keep this heater clean. DO NOT allow foreign objects

to enter any ventilation or exhaust opening as this may

cause electric shock, or fire, or damage the heater.

11. To prevent a possible fire, do not block air intakes or

exhaust in any manner. Do not use on soft surfaces, like

a bed, where openings may become blocked.

12. A heater has hot and arcing or sparking parts inside. Do

not use it in areas where gasoline, paint, or flammable

liquids are used or stored.

13. Use this heater only as described in this manual. Any

other use not recommended by the manufacturer may

cause fire, electric shock, or injury to persons.

14. Warning: In order to avoid overheating, do not cover

the heater.

15. Do not use this heater in the immediate surroundings of

a bath, a shower or a swimming pool.

16. The heater must not be located immediately below a

socket-outlet.

17. If the supply cord is damaged, it must be replaced by

the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

18. This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

19.

20. This heater is filled with a precise quantity of special oil.

Repairs requiring opening of oil-container are only to be

made by the manufacturer or his service agent who

should be contacted if there is an oil leak. When

scrapping the heater, follow the regulations concerning

the disposal of oil.

21. Children of less than 3 years should be kept away

unless continuously supervised. Children aged from 3

years and less than 8 years shall only switch on/off the

appliance provided that it has been placed or installed in

its intended normal operating position and they have

been given supervision or instruction concerning use of

the appliance in a safe way and understand the hazards

involved. Children aged from 3 years and less than 8

years shall not plug in, regulate and clean the appliance

or perform user maintenance.

22. CAUTION — Some parts of this product can become

very hot and cause burns. Particular attention has to be

given where children and vulnerable people are present.

Correct Disposal of this product

This marking indicates that this product should not be disposed with

other household wastes throughout the EU. To prevent possible

harm to the environment or human health from uncontrolled waste

disposal, recycle it responsibly to promote the sustainable reuse of

material resources. To return your used device, please use the return

and collection systems or contact the retailer where the product was

purchased. They can take this product for environmental safe

recycling.

WARNING: IN ORDER TO AVOID OVERHEATING,

DO NOT COVER THE HEATER.

PART FIGURE

Cord wrap

Caster assembly

Air Outlet

Power Indicator Light

Power Switch Knob

Thermostat Knob

Radiating unit

Air Outlet

Air Inlet

USE OF OIL FILLED RADIATOR

[Installation of the wheel carrier plate assembly]

1.Place the heater body inversely with the bottom upward.

2.Connect and tighten two wheel carrier plates to the body

with butterfly nuts as shown in the figure.

3.Place the heater upward after it is installed securely with

the wheels touching the ground.

OPERATING INSTRUCTION

[Inspection before start]

(1) The power cord shall not be damaged or fractured.

(2) This machine uses 220-240V AC power so please verify the rated current of the

power socket is in line with the requirements in the table above and is equipped

with a safety grounding device before use; otherwise, replace the socket.

[Start and power selection]

1. Start

Plug in the power, clockwise turn the thermostat knob to the "MAX" mark position,

then turn on the power switch, the heater starts to work.

2. Power selection

Under normal circumstances, please use the maximum power "HI" gear for rapid

heating. If the room temperature reaches a suitable temperature, please choose a

lower power "MED" or "LO" gear to reduce energy consumption so as to prevent

the room becoming overheated.

Note: To use the machine for the first time or to re-insert the socket, please pay

attention to check whether the plug and the socket are fitted well.

Inspection method: Insert the power plug into the socket and start for use; after

about half an hour, turn off and pull out the plug. Check whether the plug pins are

hot; replace the socket if so (more than about 50 °C) to avoid burning the plug or

even causing a fire caused by overheating of the socket due to poor contact.

[Temperature adjustment]

During use, if you feel it is necessary to lower the room temperature since it is too

high, you can use the following adjustment modes:

(1) Turn the power switch to gear "MED" or "LO".

(2) Counterclockwise turn the thermostat knob back by a certain angle, for which it

indicates that the set temperature is lower when the temperature indication is

closer to the "MIN" position.

[Fan function]

Press the fan switch to the "ON" position so that the fan heater starts working and

the room temperature will rise rapidly.

Note:

a. If the room temperature is below the set temperature, the indicator light will be

always illuminate.

b. The room shall be sealed; otherwise, the heating effect will be affected.

[Stop]

Turn the power switch to indication point "0FF", and then pull out the power plug.

[Movement of the heater]

To move the heater, turn it off first, and pull out the power plug; then push the body

to make the four casters below the body to roll.

MAIN TECHNOLOGY SPECIFICATIONS

Power supply: AC220-240V~ 50Hz

MODEL FAN LO MED HI

POWER REGULATION RANGE (W)

NY15ERF-7L

NY20ERF-9L

NY23ERF-11L

NY23ERF-13L

500

600

800

1000

900

1200

1300

1500

2000

2300

TROUBLESHOOTING

If the product does not operate or does not operate properly, first check according

to the following list. If the reason the product does not operate or does not operate

properly is not included in the following list, the product may have failed. At this time,

it is recommended to send the product to the dealer or the Media Service Center for

treatment.

Problem Possible Cause Soluon

Aer the power is

engaged, the power

indicator light does not

illuminate and the

machine does not work.

The plug may not be

plugged well.

Check whether the plug is

properly inserted into the

receptacle.

The temperature control

knob is not turned in

place.

Check whether the

temperature control knob

is turned to the ON

posion.

The machine suddenly

stops during heang.

The temperature exceeds

the threshold of the

thermal cut-oﬀ.

Cool the machine before

use.

This manual suits for next models

Table of contents

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide