Microchip Technology IS2083 Series User manual

IS2083

IS2083 SDK Debugger User's Guide

Introduction

This document describes how to use the SEGGER JLINK debugger to enable software debugging of 8051 MCU core

that is part of the IS2083BM. The SEGGER debugger makes use of IS2083BM 2-wire JTAG interface to download

8051 firmware images into IS2083BM SQI flash. It then controls the IS2083BM SQI CPU register to provide

debugging features. The following chapters describe the software and hardware prerequisites, setup and procedure

to enter the Debugging mode.

Table of Contents

Introduction.....................................................................................................................................................1

1. Quick References....................................................................................................................................3

1.1. Reference Documentation............................................................................................................3

1.2. Software Prerequisites................................................................................................................. 3

1.3. Hardware Prerequisites................................................................................................................3

2. Software Setup........................................................................................................................................6

2.1. Keil μVision Setup........................................................................................................................ 6

2.2. SDK Settings.............................................................................................................................. 10

3. Hardware Connection............................................................................................................................11

3.1. J-Link Probes Connection.......................................................................................................... 11

4. Start Debugging.................................................................................................................................... 15

4.1. Enabling Debug Mode................................................................................................................15

5. Document Revision History...................................................................................................................18

The Microchip Website.................................................................................................................................19

Product Change Notification Service............................................................................................................19

Customer Support........................................................................................................................................ 19

Microchip Devices Code Protection Feature................................................................................................ 19

Legal Notice................................................................................................................................................. 19

Trademarks.................................................................................................................................................. 20

Quality Management System....................................................................................................................... 20

Worldwide Sales and Service.......................................................................................................................21

IS2083

1. Quick References

1.1 Reference Documentation

Please go to http://www.microchip.com/IS2083 or http://www.microchip.com/BM83 to get the following documents.

•IS2083 Bluetooth® Stereo Audio SoC Data Sheet

•BM83 Bluetooth® Stereo Audio Module Data Sheet

•BM83 Bluetooth® Audio Development Board User's Guide

•IS2083 SDK User's Guide

1.2 Software Prerequisites

• IS2083 Software Development Kit

• isUpdate tool

• Please refer to the IS2083 SDK User’s Guide Section 1.2 to know what Keil® μVision® version should be used.

Furthermore, please be sure your PK51 license is valid in the support period. If your license expires on or before

the support period, Keil C51 may not allow you to use the debugger support. It depends on if your license

expiration date is on or before the C51 release date. For example, C51 9.59 released in May 2018. If your

license expired before that, you cannot use the debugger with C51 9.59. On the other hand, if your license

expired after May 2018, you can still use the debugger support. For example, the figure below shows that this

license has expired, but it can still work with C51 9.59 because it is after May 2018.

– The following DLL files enable debugging in the IS2083BM using Keil μVision:

• JLinkARM.dll

• JLinkIS2083.dll

– Initsession.ini – this file stops the Keil μVision at the first execution of SDK.

Note: The DLL files and Initsession.ini file are available in the following folder:

release-package at http://www.microchip.com/IS2083 or http://www.microchip.com/BM83.

• J-Link Commander (folder path: \Software\Debugger Support\Commander)

– An executable command prompt to check if J-Link probes can communicate with the IS2083BM.

1.3 Hardware Prerequisites

• SEGGER J-Link Debug Probe

IS2083

Quick References

Figure 1-1. J-Link Debug Probe

– J-Link PRO, J-Link ULTRA+, J-Link PLUS and J-Link BASE.

• BM83 EVB

– BM83 EVB provides a two-wire JTAG interface to communicate with the IS2083BM.

• J-Link 6-pin adapter from Microchip

IS2083

Quick References

Figure 1-2. J-Link 6-pin Adapter

IS2083

Quick References

2. Software Setup

This section describes the setup procedure of Keil uVision and IS2083 SDK to work with the debug probes.

2.1 Keil μVision Setup

This section describes the step-by-step procedure for Keil μVision setup. The user needs to first set up μVision and

connect to J-Link debug probes and later to the BM83 EVB. See 3.1 J-Link Probes Connection.

2.1.1 File Settings

Visit the Keil website to download and install the required Keil C51 (See IS2083 SDK User Guide, Section 1.2,

Software Prerequisites for the latest SDK Keil supported version.).

IS2083 SDK requires a specific Keil μVision tool to compile and operate with J-Link probes. The .dll files

customized for SEGGER J-Link debugger allows Keil μVision to communicate with the IS2083BM through J-Link

probe.

Note: After Keil μVision installation, ensure that it is not running.

Keil C51 v9.59 requires the following steps, 1 to 3 for file settings. The version v9.60 and above contains the DLL

files. Perform only step 3 for Keil C51 v9.60 and above.

Perform the following steps for the setup:

1. Go to C:\Keil_v5\ and use the text editor to open the TOOLS.INI file.

2. Insert the text TDRV10=BIN\JLinkIS2083.dll (J-Link / J-Trace IS2083 Driver) into the file as

shown below:

Figure 2-1. TOOLS.INI

3. Go to C:\Keil_v5\C51\BIN and copy the following files from the debug package to the directory:

– JLinkIS2083.dll

– JLinkARM.dll

2.1.2 Debug Settings

After verifying the J-link connection and Keil file settings, unplug and plug in the power cord to reset the IS2083BM.

This turns the J-Link LED to steady green.

Perform the following steps for debug settings:

1. Launch Keil μVision and double click MSPKv2_Application_IS2083B.uvproj and Keil uVision automatically

loads these SDK project files:

– MSPKv2_App_Pbap

– MSPKv2_App_MSPK

– MSPKv2_App_Basic

IS2083

Software Setup

– MSPKv2_App_MSPK_Debug

2. For each of the projects, right-click the "Options for Target.”

Figure 2-2. Build Target

3. In the Debug tab, select the highlighted parameters for setup. Replace S8051.DLL with -cIS208x and

DP51.DLL with -pIS208x. Load the InitSession.ini file in “Initialization File” and select the “Load

Application Setup” checkbox.

IS2083

Software Setup

Figure 2-3. Options for Target

4. Click the Settings button.

5. Select “Speed” as 12000 kHz and deselect the checkbox "Compare before download". Click OK.

IS2083

Software Setup

Figure 2-4. Debug Settings

6. To build the application and start a debug session, click

. Keil μVision is now ready to debug the IS2083BM device.

IS2083

Software Setup

Figure 2-5. Debugging Session

2.2 SDK Settings

The 2-wire JTAG debug port (i.e. P1_2 and P1_3) on IS2083BM is multiplexed with I2C function. Before debugging,

the user must enable the buildoption ENABLE_JTAG_DEBUG. This enables SW I2C and disables Low Power mode

for the debugger to run properly. The user can select MSPKv2_App_MSPK_Debug project target, which includes

ENABLE_JTAG_DEBUG buildoption.

ENABLE_JTAG_DEBUG uses SW I2C port (P2_3 and P2_6 by default) instead of HW I2C. SDK enables Low Power

mode, which turns off the debugger clock and then disconnects the debugger. ENABLE_JTAG_DEBUG is used to

disable the Low Power mode to avoid this. Refer to the IS2083 Bluetooth® Stereo Audio SoC Data Sheet for more

details on JTAG program and debug feature.

For information on which SDK features are included in MSPKv2_App_MSPK_Debug project, see the IS2083 SDK

User's Guide, Section 2.2, and Table 2-1.

Figure 2-6. Target Build

IS2083

Software Setup

Other manuals for IS2083 Series

This manual suits for next models

Table of contents

Other Microchip Technology Microcontroller manuals

Microchip Technology

Microchip Technology MCP1630 NiMH Guide

Microchip Technology

Microchip Technology PIC32MZ User manual

Microchip Technology

Microchip Technology megaAVR 0 Series User manual

Microchip Technology

Microchip Technology STK600 User manual

Microchip Technology

Microchip Technology STK600 User manual

Microchip Technology

Microchip Technology dsPIC33E/PIC24E Series User manual

Microchip Technology

Microchip Technology TCP 17051 User manual

Microchip Technology

Microchip Technology STK600 User manual

Microchip Technology

Microchip Technology SAMR34J18B User manual

Microchip Technology

Microchip Technology SAMA5D27 User manual

Microchip Technology

Microchip Technology Protouch2 User manual

Microchip Technology

Microchip Technology PIC32MX5XX User manual

Microchip Technology

Microchip Technology MCP1630V User manual

Microchip Technology

Microchip Technology DM164120-1 User manual

Microchip Technology

Microchip Technology PIC18C 8 Series User manual

Microchip Technology

Microchip Technology PIC16C62B User manual

Microchip Technology

Microchip Technology SAM L11 Xplained Pro User manual

Microchip Technology

Microchip Technology dsPIC33E USB User manual

Microchip Technology

Microchip Technology ATmega328PB Xplained Mini User manual

Microchip Technology

Microchip Technology PIC24FV16KM204 FAMILY User manual

Microchip Technology

Microchip Technology PIC32MZ User manual

Microchip Technology

Microchip Technology SAM E54 Xplained Pro User manual

Microchip Technology

Microchip Technology MCP1631 Guide

Microchip Technology

Microchip Technology SAMR34 Xplained PRO User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide