Metra Electronics 99-7413 User manual

DIN HEAD UNITS: Slide the DIN cage into the Housing and secure by bending the metal

locking tabs down. Slide the aftermarket head unit into the cage until secure. (see Fig. B)

ISO-DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate. Snap the

Faceplate into the Housing and attach the ISO-DIN Spacers to the inner walls of the Mounting

Brackets by inserting the Spacer pegs into the Bracket holes. Slide the aftermarket head unit

into the back of the kit and mount the Brackets to the unit with (4) 5mm Flat-head Screws

supplied. (see Fig. C)

(If an equalizer will be included, slide the unit into the back of the Radio Housing and secure.

If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening).

2-SHAFT HEAD UNITS: Snap the Faceplate

into the Radio Housing, slide the aftermarket

head unit into the kit and secure with shaft

nuts. (see Fig. A)

ALL VEHICLES

6 7

Locate the factory wiring harness in the

dash. Metra recommends using the

proper mating adaptor and making

connections as shown. (Isolate and

individually tape off the ends of any

unused wires to prevent electrical short

circuit).

A) Strip wire ends back ½"

B) Twist ends together

C) Solder

D) Tape

99-7413

INSTALLATION

INSTRUCTIONS

APPLICATIONS

CAR PAGE

NISSAN

Altima 1993-97........................................................... 1

Altima 1998-01........................................................... 2

KIT COMPONENTS

TOOLS REQUIRED

Cutting tool

Wrench

Phillips screwdriver

Equalizer

Dummy Plate

(6) #6 Self-tapping

Screws

(4) 5mm Flat-head

Screws

Fig. C

Fig. A

Radio Housing

Faceplate

ISO-DIN

Spacers

Mounting

Brackets

Fig. B

Re-connect the battery terminal and test the unit

for proper operation. Mount the head unit/kit

assembly to the sub-dash with (4) Phillips screws

removed in step #1.

1-800-221-0932 www.metraonline.com

rev. 250701

Disconnect the negative battery terminal to

prevent an accidental short circuit. Remove

the shifter cover and (4) Phillips screws

exposed. Remove (2) screws from the

driver's side knee bolster and lower.

Remove (1) screw from the left corner of the

radio triim bezel. Remove (2) screws above

the radio opening and unclip the bezel.

Remove (4) screws from the factory head

unit assembly and disconnect the wiring.

Disconnect the negative battery terminal to

prevent an accidental short circuit. Unclip

the gear shifter trim bezel and remove (2)

Phillips screws exposed. Remove (2)

Phillips screws above the radio opening.

Unclip the radio trim bezel. Remove (4)

Phillips screws from the factory head unit

and disconnect the wiring.

Using the raised lines as a guide, cut and

remove the ends of each Mounting Bracket

("A").

Locate the corner of each lower mounting

tab on the Mounting Brackets ("A").

Using the corner of each mounting tab as a

guide, cut and remove the ends of the

cupholder mounts from the Mounting

Brackets ("B").

Align the holes in the Mounting Brackets

with the holes in the Radio Housing and

mount with (6) #6 Self-tapping Screws

supplied.

Remove (4) screws securing the cupholder

to the factory head unit assembly and

remove. Slide the cupholder into the bottom

of the Radio Housing and mount with the

same (4) screws. Skip to the Installation

Instructions for ALL VEHICLES on Page #3.

NISSAN Altima 1993-97 NISSAN Altima 1998-01

1 1

2 2

Align the OUTER holes in the Mounting

Brackets with the holes in the Radio

Housing and mount with (6) #6 Self-

tapping Screws supplied. (The Brackets

will mount on an angle). Skip to the

Installation Instructions for ALL VEHICLES

on Page #3.

"A" "A"

"B"

Table of contents

Other Metra Electronics Automobile Accessories manuals

Metra Electronics

Metra Electronics 99-9401 User manual

Metra Electronics

Metra Electronics 99-7893 User manual

Metra Electronics

Metra Electronics 95-7324 User manual

Metra Electronics

Metra Electronics 95-3304 User manual

Metra Electronics

Metra Electronics 70-7306 User manual

Metra Electronics

Metra Electronics 70-8116 User manual

Metra Electronics

Metra Electronics 99-8903B User manual

Metra Electronics

Metra Electronics 99-7300 User manual

Metra Electronics

Metra Electronics TE-RVMCBT User manual

Metra Electronics

Metra Electronics 95-6513B User manual

Metra Electronics

Metra Electronics 99-3314G User manual

Metra Electronics

Metra Electronics 95-9616B User manual

Metra Electronics

Metra Electronics 95-7378B User manual

Metra Electronics

Metra Electronics 99-5500 User manual

Metra Electronics

Metra Electronics 88-00-3302 User manual

Metra Electronics

Metra Electronics 99-6536 User manual

Metra Electronics

Metra Electronics 99-7524B User manual

Metra Electronics

Metra Electronics 99-7631B User manual

Metra Electronics

Metra Electronics 99-7423 User manual

Metra Electronics

Metra Electronics 98-9306 User manual

Metra Electronics

Metra Electronics 99-6510 User manual

Metra Electronics

Metra Electronics 99-7318 User manual

Metra Electronics

Metra Electronics 95-3023HG User manual

Metra Electronics

Metra Electronics 99-5600 User manual

Popular Automobile Accessories manuals by other brands

James Baroud

James Baroud Odyssey user guide

Motorola

Motorola i50sx owner's manual

Yakima

Yakima 9MM STANDARD BIKE MOUNT instructions

Feniex

Feniex T3 instruction manual

Renault

Renault 77 11 423 180 Installation instruction

Kia

Kia E8300-4D000 manual

Brink

Brink 756843 installation instructions

Whispbar

Whispbar K085W Fitting instructions

v.link

v.link CI-VL2-PC-HSD manual

Viking

Viking Stack-Rack Assembly and use instructions

Aries

Aries 203015 installation manual

Choetech

Choetech AT0005 user manual

ZZ2

ZZ2 ZZAIR-PRO instruction manual

Holman

Holman 4A80L installation guide

Thule

Thule 2075 parts manual

Motorola

Motorola T325 quick start guide

TAUBENREUTHER

TAUBENREUTHER 16-3950 FITTING INSTRUCTION

DV8

DV8 FBJL-02 Product installation manual