Meanwell KNX-20E-640 User manual

http://www.meanwell.com

KNX-20E-640 Installation Manual

Introduction

The KNX Power Supply KNX-20E-640 is a 640mA power supply with high efficiency and a small footprint of only 3SU (52.5mm). The

device has a KNX bus choke output and an additional output for ancillary power. The -5℃~ +50℃wide temperature operating range

can meet all kinds of applications. LED indicators are used in case of normal operation, overload conditions and RESET operation. It is

perfectly suitable to power up any products labeled with the KNX trademark.

Features

•EIB/ KNX power supply with integrated choke

•Compact size with 3US (52.5mm) width

•Safety extra low voltage (SELV)

•180 ~ 264Vac input

•No load power consumption < 0.5W

•200ms mains failure back-up time

•Cooling by free air convection

•Isolation classⅠ

•LED indicator for normal operation, bus reset and bus overload

•Installed on DIN TS-35/7.5 or 15

•3 years warranty

•Protections: Short circuit/ Overload (short-circuit-proof)/ Over voltage

Display

The device is equipped with a reset push button, three LEDs and terminal blocks for the AC, KNX bus line and ancillary output.

KNX bus terminal (Red : BUS +V, Black : BUS -V)

Ancillary power terminal

RESET button

Power ON (Green)

Reset (Red)

Ⅰ> Ⅰmax (Red)

AC terminal (L,N, )

http://www.meanwell.com

Installation

1. Wiring

•Use wires with an adequate cross-section

•Use suitable mounting tools to do the wiring and mounting

•The maximum number of bus devices connected is 64

•The maximum length of a line segment is 350 m, measured along the line between the power supply and the furthest bus device

•The maximum distance between two bus devices cannot exceed 700 m

•The maximum length of a bus line is 1000 m, keeping into account all segments

Type

AC and ancillary power terminals

(L, N, , +V, -V)

KNX bus terminal

(BUS +V, BUS -V)

Solid wire

0.5 ~ 4.0mm

0.6 ~ 0.8Φ

Stranded wire

0.5 ~ 2.5mm2

------

American wire gauge

12 ~ 26AWG

20 ~ 22AWG

Wire stripping length

6.5mm (0.255")

5mm (0.196”)

Screwdriver

3mm Slotted

-----

Recommended tightening torque

8 kgf-cm (7 lb-in)

-----

2. Mounting and Connection

a. Insert the power supply onto the DIN rail (TS35/7.5 or TS35/15).

b. Connect the KNX, the connection to the KNX bus line is made with the terminal block (red: BUS +V/ black: BUS -V )

located on the left upper part of the front.

c. Connect the mains voltage, the connection to the AC is made with the terminal (L, N, ) located on the bottom.

Click

http://www.meanwell.com

3. MCB

Use a MCB (miniature circuit breaker) with an adequate current rating to protect the KNK device.

Model

B10

B16

C10

C16

KNX-20E-640

Note: These calculated values are based on MCB S201 series manufactured by ABB.

Function and Operation

The device does not require any configuration with ETS® (Engineering Tool Software) tool. Once the wiring is proper done, the “Power on”

LED will light up and the rest of the LEDs remain off to indicate that the unit is in operation condition.

Reset：To carry out a reset, press the RESET button for at least 20 seconds to reset the KNX power supply.

Fault：If the red LED (I > Imax) lights up with applied mains voltage, a fault is present. This means that the KNX output is overloaded or

shot-circuited. The problem can be solved by removing the cause of the short circuit or by reducing the number of KNX devices

connected to the line. Once the fault has been rectified, carry out a reset by pressing the RESET button for approx. 20 seconds.

Meaning of the LEDs

Power ON (GREEN)

Reset (RED)

I > Imax (RED)

Status

OFF

Ready for operation or

working normally

OFF

Resetting

OFF

Output current too high

OFF

Short-circuit or bus

reverse polarity

OFF

No mains voltage

Environmental Limitations

•Maximum ambient temperature must not exceed 50℃

•Always allow adequate ventilation clearances, 5mm left and right, 40mm above and 20mm below, around the unit in use to prevent it

from overheating

•Only install the unit in indoor environments

Cautions

•This unit must be installed by a qualified electrician

•It should be ensured that the supply can be isolated when connecting the unit.

Other Meanwell Power Supply manuals

Meanwell

Meanwell PWR24048 User manual

Meanwell

Meanwell SHP-10K-HV Series User manual

Meanwell

Meanwell MP450 User manual

Meanwell

Meanwell ELG-150-C Series User manual

Meanwell

Meanwell APV-25 User manual

Meanwell

Meanwell DRA Series User manual

Meanwell

Meanwell DR Series User manual

Meanwell

Meanwell MDR Series User manual

Meanwell

Meanwell DRP-3200 Series User manual

Meanwell

Meanwell LCM-25KM User manual

Meanwell

Meanwell DDR-15G-3.3 User manual

Meanwell

Meanwell DRS Series User manual

Meanwell

Meanwell LCM-25 User manual

Meanwell

Meanwell DR-15-12 User manual

Meanwell

Meanwell NDR-240 Series User manual

Meanwell

Meanwell NDR-75 Series User manual

Meanwell

Meanwell DDR-120A-12 User manual

Meanwell

Meanwell HEP-1000 User manual

Meanwell

Meanwell SHP-30K-HV Series User manual

Meanwell

Meanwell TDR-240-24 User manual

Meanwell

Meanwell ICL-16L Series User manual

Meanwell

Meanwell AP User manual

Meanwell

Meanwell RCP-2000 User manual

Meanwell

Meanwell KNX-40E-1280D User manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

HP 6200B Operating and service manual

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual