Maytag W10117890A User manual

AUTOMATIC WASHER

USE & CARE GUIDE

W10117890A

TABLE OF CONTENTS

WASHER SAFETY .................................................................. 3

INSTALLATION REQUIREMENTS ........................................ 5

Tools and Parts .................................................................. 5

Location Requirements ...................................................... 5

Drain System ..................................................................... 6

Electrical Requirements...................................................... 7

INSTALLATION INSTRUCTIONS ......................................... 8

Before You Start ................................................................. 8

Remove Shipping Materials ............................................... 8

Level the Washer ............................................................... 9

Connect Drain Hose ........................................................ 10

Connect the Inlet Hoses................................................... 11

Secure the Drain Hose..................................................... 13

Complete Installation.......................................................13

WASHER USE...................................................................... 14

Starting Your Washer ....................................................... 14

WASHER CARE ................................................................... 16

Cleaning Your Washer..................................................... 16

Water Inlet Hoses ............................................................ 16

Moving and Storage......................................................... 16

TROUBLESHOOTING ........................................................ 17

Washer and Components ................................................ 17

Washer Operation ........................................................... 17

Washer Results ................................................................ 18

ASSISTANCE OR SERVICE .................................................. 20

WASHER SAFETY

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

Read all instructions before using the washer.

■

Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with petrol, dry-

cleaning solvents, other flammable or explosive

substances as they give off vapours that could ignite or

explode.

■

Do not add petrol, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapours that could ignite or

explode.

■

Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water taps and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

this time.

■

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer

is used near children.

■

The appliance is not intended for use by young children or

infirm persons without supervision.

■

Before the washer is removed from service or discarded,

remove the door or lid.

■

Do not reach into the washer if the drum, tub or agitator is

moving.

■

Do not install or store the washer where it will be exposed to

the weather.

■

Do not tamper with controls.

■

Do not repair or replace any part of the washer or attempt

any servicing unless specifically recommended in this Use

and Care Guide or in published user-repair instructions that

you understand and have the skills to carry out.

■

See Installation Instructions for earthing requirements.

■

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified

person in order to avoid a hazard.

WARNING:

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. The parts supplied are in the

washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

Parts supplied:

Tools needed for securing the drain hose and leveling the washer:

Parts supplied:

Alternate Parts

Your installation may require additional parts. For information on ordering, please refer to the

toll-free phone numbers on the front page of the Use and Care Guide.

Location Requirements

Selecting the proper location for your washer improves performance and minimizes noise and

possible washer “walk.”

Your washer can be installed in a basement, laundry room, closet, or recessed area. See

“Drain System.”

IMPORTANT: Do not install or store the washer where it will be exposed to the weather.

Proper installation is your responsibility.

You will need:

■A water heater set to deliver 120°F (49°C) water to the washer.

■A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is

attached to the back of the washer. See “Electrical Requirements.”

■Hot and cold water faucets located within 3 ft (91 cm) of the hot and cold water fill

valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers

require 20-100 psi (138-690 kPa) for best performance.

■A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the

washer on carpeting is not recommended. Ventilation openings in the base must not be

obstructed by carpet.

■A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kg).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can

remain in the washer and can cause damage in low temperatures. See “Washer Care” for

information on winterizing.

■Pliers that open to 1⁹⁄₁₆"

(3.95 cm)

■Flat-blade screwdriver

■Flashlight (optional)

A. Water inlet hose (2)

B. Drain hose form

C. Drain hose extension

D. Drain hose coupling

E. Large flat washer (4)

F. Small flat washer (2)

G. Inlet hose adapter

H. Hose clamp (2)

■Adjustable or open end

wrench ⁹⁄₁₆" (14 mm)

■Level

■Wood block

■Ruler or measuring tape

A. Beaded tie strap

B. Front leveling feet with nuts (2)

ABCD

EFGH

If You Have: You Will Need to Buy:

Laundry tub or standpipe

taller than 96" (2.4 m)

Sump pump system (if not already available)

Overhead sewer Standard 20 gal. (76 L) 39" (99 cm) tall drain tub or utility

sink, sump pump and connectors (available from local

plumbing suppliers)

Floor drain Siphon break kit, Part Number 280129; additional drain

hose, Part Number 3357090

Water faucets beyond reach

of fill hoses

2 longer water fill hoses:

6 ft (1.8 m) Part Number 76314,

10 ft (3.0 m) Part Number 350008

Drain hose too short Drain hose kit, Part Number 280131

Lint clogged drain Drain protector, Part Number 367031

Recessed area or closet installation

The dimensions shown are for the recommended spacing allowed (A and B), except the closet

door ventilation openings. The dimensions shown for the closet door ventilation openings (C)

are the minimum required.

■Additional spacing should be considered for ease of installation and servicing.

■Additional clearances may be required for wall, door and floor moldings.

■Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce

noise transfer.

■If a closet door is installed, the minimum air openings in the top and bottom of the door

are required (C). Louvered doors with air openings in the top and bottom are acceptable.

■Companion appliance spacing should also be considered.

Drain System

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub

drain system, or the floor drain system. Select the drain hose installation method you need.

See “Tools and Parts.”

Standpipe drain system - wall or floor (views A & B)

The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum

carry-away capacity can be no less than 17 gal. (64 L) per minute. A 1¹⁄₄" (3.2 cm) diameter to

1" (2.5 cm) diameter standpipe adapter kit is provided. See “Tools and Parts.”

The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm)

from the bottom of the washer.

To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be inside the standpipe.

Secure drain hose with beaded tie strap.

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be

at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the

washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See “Tools

and Parts.”

The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer.

Additional hoses might be needed.

To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be below the top of the

wash tub. Secure drain hose with beaded tie strap.

A. Front view

B. Side view

C. Closet door with vents

ABC

19"

(48.3 cm)

(0 cm)

(0 cm) 27"

(68.6 cm) 1"

(2.5 cm) 25¹⁄₂"

(64.8 cm) 4"

(10.2 cm)

14" max.

(35.6 cm)

(7.6 cm)

24 in.

(155 cm )

48 in.

(310 cm )

39"

(99 cm)

39"

(99 cm)

28"

(71 cm)

Electrical Requirements

■A 220 volt, 60 Hz., AC only, 8- or 10-amp, fused electrical supply is required. A time-

delay fuse or circuit breaker is recommended. It is recommended that a separate circuit

serving only this appliance be provided.

■This washer is equipped with a power supply cord having a grounding plug.

■To minimize possible shock hazard, the cord must be plugged into a mating, grounding-

type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is

not available, it is the personal responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualified electrician.

■If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

■Do not ground to a gas pipe.

■Check with a qualified electrician if you are not sure the washer is properly grounded.

■Do not have a fuse in the neutral or ground circuit.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

GROUNDING INSTRUCTIONS

For a grounded, cord-connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING:

Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance – if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the appliance.

INSTALLATION INSTRUCTIONS

Before You Start

NOTE: To avoid floor damage, set the washer onto cardboard before moving across floor.

Remove Shipping Materials

Removing the shipping material is necessary for proper operation. If the shipping material is

not removed, the washer will make excessive noise.

1. Move the washer to within approximately 3 ft (90 cm) of its final location.

2. The washer must be in the upright position and not tilted before removing the shipping

material.

3. Locate the yellow shipping materials on the rear of the machine, near the bottom. Follow

the steps for your particular model, either the one with the straight power cord and cord

restraint or the looped power cord version.

Straight power cord

1. Remove power plug and yellow strap from machine base to release the rear leveling

system.

2. Firmly grasp the power cord and pull to completely remove the power cord, cord

restraint, and pin from the rear panel.

3. Confirm that the power cord restraint (A), and pin (B) are removed.

4. To remove the power cord from the cord restraint, push the power cord in, press TAB, and

then pull the power cord out.

Straight power cord

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

A. Power cord restraint B. Pin

Looped power cord

1. Firmly grasp the yellow shipping strap and pull until both ends are completely removed

from washer.

2. Check that two (2) cotter pins were removed with the shipping strap.

Level the Washer

Properly leveling your washer avoids excessive noise and vibration.

Install the Front Leveling Feet

1. Prop up the front of the washer about 4" (10.2 cm) with a wood block or similar object.

The block needs to support the weight of the washer.

2. Screw the locknut onto each foot to within 1" (2.5 cm) of the foot base.

3. Screw the feet into the threaded holes at the front corner of the washer until the nuts

touch the washer. Twist the feet to install.

NOTE: Do not tighten the nuts until the washer is level.

4. Tilt the washer back and remove the wood block. Gently lower the washer to the floor.

Looped power cord

A. Threaded holes for feet

(10.2 cm)

(2.5 cm)

Steps in Final Location

1. Slide the washer to its final location.

2. Tilt the washer forward until the rear of the washer is at least 4" (10.2 cm) off the floor. You

may hear the self-adjusting rear feet click into place. Lower the washer to the floor.

3. Check the levelness of the washer by placing a level on the top edges of the washer, first

side to side, then front to back.

4. If the washer is not level, move the washer out slightly, tip back, prop up the front of the

washer with the wood block and adjust the feet up or down as necessary by twisting the

feet. Turn the feet clockwise to raise the washer or counterclockwise to lower the washer.

Repeat steps 1 through 4 until washer is level.

5. After the washer is in its final location and level, use a ⁹⁄₁₆" or 14 mm open-end wrench to

turn the nuts counterclockwise on the feet tightly against the washer cabinet.

IMPORTANT: If the nuts are not tight against the washer cabinet, the washer may vibrate.

Connect Drain Hose

Proper connection of the drain hose protects your floors from damage due to water leakage.

Read and follow these instructions.

The drain hose is connected to your washer and is stored inside the washer cabinet.

Remove drain hose from washer cabinet

Gently pull the corrugated drain hose out of the washer from the top of the hose. Continue to

pull the hose until the end emerges. Do not force excess drain hose back into the rear of the

washer.

A. Self-adjusting feet

(10.2 cm)

Table of contents

Other Maytag Washer manuals

Maytag

Maytag MHWE450WJ User manual

Maytag

Maytag MHWE300VW11 User manual

Maytag

Maytag MVWC465HW2 User manual

Maytag

Maytag MVWB450WQ0 User manual

Maytag

Maytag Bravos W10092822A User manual

Maytag

Maytag BRAVOS XL MVWB750YW Assembly instructions

Maytag

Maytag MVW6230H Assembly instructions

Maytag

Maytag MAT15MN User manual

Maytag

Maytag MXS Series User manual

Maytag

Maytag MHWE950WJ Assembly instructions

Maytag

Maytag MHWE950W Series Parts list manual

Maytag

Maytag MHW7000AG0 User manual

Maytag

Maytag MVW18PD User manual

Maytag

Maytag SAV-1 User manual

Maytag

Maytag MAV-2 User manual

Maytag

Maytag Neptune TL FAV6800A Assembly instructions

Maytag

Maytag MAVT346AWW User manual

Maytag

Maytag MVWB300WQ0 User manual

Maytag

Maytag MAV-18 User manual

Maytag

Maytag PERFORMANCE SERIES User manual

Maytag

Maytag MTW6700TQ1 User manual

Maytag

Maytag Neptune MAH3000 User manual

Maytag

Maytag MAT12CS User manual

Maytag

Maytag Neptune SL-3 User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide