Maytag MLI7500AAW User manual
MLI7500AAW Maytag™ Cordless Electronic
Steam Iron
®
USER’SGUIDE
Table of Contents
Safety Instructions ....................................1-2
Controls .........................................................3
Features .........................................................4
Preparing to Iron...........................................5
Setting the Temperature...............................6
Heating the Iron.............................................7
Using Steam Features ..................................8
Using the Spray Function ............................9
After Use/Storage .......................................10
Maintenance.................................................11
Trouble Shooting ........................................12
Warranty.......................................................13
Congratulations on your purchase of a
Maytag™ Cordless Steam Iron! Your
satisfaction is very important to us.
Before operating this iron, please read these
instructions completely. This manual should
be kept for future reference. It contains
instructions to acquaint you with proper
operating procedures for your iron.
If you have questions, call or write us (include
your model and serial numbers and your
phone number):
Maytag Appliances Sales Company
Attn. CAIR®Center
P.O. Box 2370
Cleveland, TN 37320-2370
1-877-366-5426 USA
1-800-688-2002 CANADA
1-800-688-2080 USA TTY (for deaf,
hearing impaired, or speech impaired)
(Mon.-Fri., 8am-8pm Eastern Time)
Internet: http://www.maytag.com
10/02 MCS Part No. 16022001
1
IMPORTANT SAFEGUARDS
When using your cordless steam iron, basic safety precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
1. Use iron only for its intended use.
2. To protect against a risk of electric shock, do not immerse the iron in water or other
liquids.
3. The iron should always be turned OFF before plugging or unplugging cradle cord
from outlet. Never yank cord to disconnect from outlet; instead, grasp plug and pull
to disconnect.
4. Do not allow cord to touch hot surfaces. Retract cord into cord reel unit when
storing.
5. Always disconnect cradle cord from electrical outlet when filling iron with water and
when not in use. Be careful to avoid spilling water over iron when filling.
6. Do not operate iron with a damaged cord or if the iron or cradle has been dropped or
damaged. To avoid a risk of electric shock, do not disassemble the iron or cradle.
Incorrect reassembly can cause a risk of electric shock when the iron is used.
7. Close supervision is necessary for any appliance being used by or near children. Do
not leave iron unattended while connected to an electrical outlet or on an ironing
board. Always position iron carefully to prevent it from falling if ironing board is
accidentally bumped or if cord is pulled. When not in use, always place iron securely
into cradle.
8. Burns can occur from touching hot metal parts, the hot surface of the cradle, hot
water, or steam. Use caution when turning a steam iron upside down. There may
be hot water in the reservoir.
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not operate another high-wattage appliance on the
same circuit.
2. If an extension cord is absolutely necessary, a 12 ampere cord should be used.
Cords rated for less amperage may overheat. Care should be taken to arrange the
cord so that it cannot be pulled or tripped over.
SAVE THESE INSTRUCTIONS
2
Be sure that these precautions
are carefully followed.
SAFETY PRECAUTIONS
When retracting the electrical cord, keep
hold of the plug.
If the plug is not held,
the uncontrolled moving
plug may cause injury.
Be sure that your hands and arms do not
come into contact with the hot steam.
Touching hot steam
can cause burns.
Do not touch high heat areas, such as the
hot soleplate or support area.
Touching hot areas can cause burns.
Do not direct steam toward people or
toward clothes that are being worn by a
person.
Hot steam can cause burns.
Prevent the entry of dust and dirt into the
charging pins and contact points area. Be
sure that metal objects, such as pins or
wires, never come into contact with these
areas.
Touching the contact points with any pins or wires can
cause short-circuiting, electric shock and fire.
Do not tilt the iron or shake it rapidly back
and forth.
These actions can cause hot water to leak from the
water inlet/outlet spout, resulting in possible burns.
Do not use steel wool or other abrasives
to polish the charging pins.
This action may result in
faulty connections.
Do not press the burst of steam button
rapidly, over and over again.
If the burst of steam button is
pressed at intervals of less than
2 seconds, hot water droplets
may be discharged, possibly
causing burns.
Do not pour water onto the iron or cradle.
This action
may cause
a malfunction.
Be sure that the soleplate does not come
into contact with the surface of the iron
cradle or case.
This action may
deform or
damage the
surface of the
iron cradle or case.
3
CONTROLS
13
2
4
Temperature Control Button
Off/Auto Off Light
Temperature Indicator Lights
Burst of Steam Button
Steam Button
Spray Button
Ready Light
•Pressing this button will
discharge a powerful shot
of steam.
•This light will illuminate when the
appropriate operating
temperature is reached.
•During ironing, the ready light will
begin to flash whenever the
temperature of the iron starts to
decrease. If the temperature
continues to decrease, the light
will eventually turn off. When the
light begins to flash, place the
iron back on the cradle for
reheating. Once the soleplate
heats up to the appropriate
operating temperature, the light
will again illuminate.
•The selected light will continue
flashing until the preset
temperature is reached.
•Once the preset temperature is
reached, the light will stop
flashing and remain illuminated.
•If the iron is not on the cradle,
these lights will not be
illuminated.
•Leave button up for steam, press
down for a dry iron.
•Pressing this button will
discharge a mist of water from
the spray nozzle.
The “OFF / AUTO OFF” light will
flash when:
•The electrical plug is inserted into
the electrical outlet.
•The temperature is set to “OFF”.
•The auto-shutoff function is
activated.
•If the iron is left on the cradle with the power still on, it will automatically shut off after
approximately 10 minutes. The “Auto off” light will illuminate.
Press this button firmly, once the iron
has been placed on the cradle.
•Each time this button is pressed, the
flashing light will cycle to the next
temperature indicator, in the order
shown by the arrows in the diagram.
•In order to avoid a malfunction
caused by accidental button contact,
the iron has been designed so that
the activation of the temperature
control button requires additional
pressure.
4
FEATURES
How does a cordless iron work?
•The iron rests on a cradle that supplies the power to heat the iron.
•Each time you set aside the iron to adjust a garment on the ironing board, the iron should
be placed back on the cradle. This will allow the iron to quickly “heat” so the temperature
of the iron remains at the desired level.
FULL indicator
Spray nozzle
Anti-drip Control
Iron
Cradle
Case
Tank
Red tape
Lock/Release button
Soleplate
Handle
Temperature
control
Case latch
Controls
Cord (cord reel) Electrical plug
If the temperature of the
soleplate decreases significantly
during iron usage, this function
will be activated to stop the
production of steam.
Press this button to remove
the water tank.
Do not over-extend the cord
by pulling it farther than the
section marked by this red
tape.
Lid for water inlet /outlet
spout. This lid prevents debris
from entering the spout.
5
PREPARING TO IRON
1Preparation
1. Remove the case.
2. Pull the electrical cord out only to the
length required. Insert the plug all the
way into an electrical outlet.
120 V AC
Red tape
•Do not over-extend the cord farther
than the section marked by this red
tape.
2Filling with Water
It is not necessary to pour water into the
water tank if not using steam or water spray
features.
1. Press down the steam button to set the
iron to the “Dry” position.
2. Remove the tank and fill it with water, up
to the mark indicating “FULL”.
While pressing down
the release button,
remove the tank.
Fill with tap water
•Regions that have extremely hard
water should use a mixture of 50% tap
water and 50% distilled water.
•Do not use water treated by household
soft water systems, as it contains
minerals that are harmful to the iron.
•Do not fill the iron with water in excess
of the mark indicating “FULL”. If too
much water has been poured in,
steam will be discharged continuously
whenever the iron is placed on the
cradle.
3. Close the inlet/ outlet spout lid, then
reinstall the tank onto the iron.
Push water tank all the way in until it
clicks.
Click!
6
SETTING THE TEMPERATURE
1. Place the iron on the
cradle.
2. Press the steam
button down.
3. Press the
temperature control
button until the desired temperature
indicator light is flashing.
•The temperature setting cannot be
changed unless the iron is on the
cradle.
•Refer to the Fabric Guide (shown
below) to select proper temperature
setting.
•Irons heat up more quickly than they
cool down, so start with lower
temperature settings and gradually
increase as needed.
•When ironing fabric blends, select a
temperature setting for the fabric
component that requires the lowest
temperature.
•When ironing fabrics that are
especially susceptible to heat, first
“test the fabric” by ironing in an
inconspicuous area of the fabric.
Utilize a pressing cloth as needed.
•Be sure to read garment care labels
since using improper temperature
settings could damage fabrics.
Settings
Choose the appropriate setting to suit the
fabric.
Fabric Guide
Setting Synthetics Wool/Silk Linen/Cotton
Acrylic Silk Linen
Acetate Wool Cotton
Fabric Type Nylon Rayon
Velvet
Polyester
Temperature Low Medium High
Note: When ironing velvet, use steam but do not let the iron touch the fabric.
Test an inconspicuous area first before proceeding.
•The steam range is indicated for higher
temperature settings.
•When steam-ironing fabrics that require
lower temperature steam than is available
with the lowest steam setting, a pressing
cloth suitable for use with the particular
steam setting should be placed on top of
the fabric.
Press
Wait until the
selected light
begins to flash.
7
HEATING THE IRON
1. After setting the temperature, allow
the iron to preheat on the cradle. The
iron will be ready for use once the
ready light illuminates, approximately
1 - 2 minutes.
•If the temperature setting is changed
from high to low during iron operation,
the ready light will turn off and the
temperature indicator light will begin
flashing. The iron will be ready for use
once the ready light again illuminates
and the temperature indicator light
stops flashing.
•When the iron is removed from the
cradle, the temperature indicator
light will turn off.
Example: When “linen/cotton” has
been selected
2. Be sure that the iron is always placed
back on the cradle whenever you take
a break from ironing or when you
adjust clothes on the ironing board.
•The ready light will begin to flash
whenever the temperature of the iron
starts to decrease. If the temperature
continues to decrease, the light will
eventually turn off. When this occurs,
place the iron back on the cradle for
reheating.
•The iron will be ready to use once the
ready light illuminates.
•The most efficient ironing
performance will be obtained when
the iron is reheated briefly each
time the iron is placed on the cradle
while adjusting a garment during
normal ironing.
•When returning the iron to its cradle,
never place it in a sideways or
backwards position. The contact points
will become deformed and the iron will
not be able to heat properly.
•Steam may occasionally continue to
discharge for a short time after the iron
has been placed back on the cradle.
This is normal.
Place
correctly
Cuff Press
When used as a “dry” iron, the removal of
the water tank allows the iron to be used for
pressing hard to reach
areas such as sleeves,
cuffs and childrens clothes.
8
USING STEAM FEATURES
Steam
•Choose a
setting within
the steam range
on the
temperature control.
•Steam will help remove
stubborn wrinkles on
wool, cotton and linen
fabrics.
•To iron velvet, use
steam but do not let the
iron touch the fabric.
Burst of Steam
Be sure that the iron is operated
using the “linen /cotton” setting.
•Press the Burst of Steam button at
intervals of 2 - 5 seconds to apply powerful
shots of steam directly onto wrinkles.
•If the burst of steam button is pressed at
shorter intervals, hot water droplets may
be discharged.
•If shots of steam are not discharged during
initial usage, press the burst of steam
button several times.
•NEVER iron clothes while being worn.
•DO NOT use the burst of steam feature
with delicate fabrics.
•In the event that the steam/ bursts of steam are not easily discharged due to insufficient
water within the tank, refill the tank with water up to the mark indicating “FULL”.
(☞Refer to page 5.)
•If the bursts of steam decrease during usage, place the iron back on the cradle for reheating.
(If the burst of steam button has been operated more than 10 times consecutively, hot water
droplets may be discharged.)
•Do not place the iron on its side or upside down. This may cause water leakage and may
result in burns due to the escape of hot water.
9
USING THE SPRAY FUNCTION
•The spray button can be utilized with either the “Dry” or the “Steam” functions.
•The spray button should be pressed only while the iron is kept level.
•If the spray does not discharge upon initial usage, then
press the spray button several times.
•The spray function helps to smooth cotton and linen
fabrics, as well as stubborn wrinkles on other fabrics.
•Some fabrics may stain if sprayed with water, so consult the
garment care label carefully.
•When storing the iron after using the spray function, press the
spray button several times after the water has been drained
from the tank, to be sure that all water is completely removed
from within the spray unit.
Table of contents
Languages:
Other Maytag Iron manuals
