Marsh TD2100 User manual
Marsh Shipping Supply Co. LLC
Marsh TD2100 Electric Taper
Technical Manual
®
2
A wall-socket must be close to the product and readily accessible.
The overall system is protected against overload by the branch circuit
protection in accordance with the current edition of the NEC or CEC
Introduction
Specifications
Setup Instructions
Operating Instructions
Maintenance
Troubleshooting
The machine will not feed tape.
The ON/OFF switch is not illuminated.
The motor doesn’t run.
The machine doesn’t operate when a key is pushed.
The tape slips at the feed wheel.
The machine doesn’t stop feeding tape.
The cutter doesn’t cut the tape.
The tape is jamming or tearing.
The tape is cut, but the cutter blades don’t return to neutral position.
The tape is not the correct length.
The tape doesn’t stick to the carton.
The tape slips on the carton.
The heater doesn’t heat.
RepairRemoving the Right Side Cover
Attaching the Right Side Cover
Removing the Left Side Cover
Attaching the Left Side Cover
Removing the Timing Belt
Attaching the Timing Belt
Removing the Small Timing Pulley
Attaching the Small Timing Pulley
Removing the Large Timing Pulley
Attaching the Large Timing Pulley
Removing the Pinch Roller
Attaching the Pinch Roller
Removing the Weighted Brush Cover
Attaching the Weighted Brush Cover
Removing the Tape Channel Plate
Attaching the Tape Channel Plate
Removing the Tape Basket/Motor Cover
Attaching the Tape Basket/Motor Cover
4
5
6
9
12
14 14
15
15
17
17
18
18
19
19
19
20
20
21
22 23
23
25
25
27
27
28
28
29
29
30
30
33
33
35
35
37
37
Table of Contents
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
Need Parts? We have all parts on our
website with pictures and prices.
Visit:
http://www.propacksolutions.com/2100-
Electric_c_428.html
or call 877-776-7225 toll free.
3
39
39
41
41
43
44
46
46
48
48
50
50
52
53
54
54
56
56
58
59
61
62
64
73
74 74
74
Removing the Water Tank Holder
Attaching the Water Tank Holder
Removing the Movable Cutter Assembly
Attaching the Movable Cutter Assembly
Removing the Gearbox/Motor Mount with the Motor Attached
Attaching the Gearbox/Motor Mount with the Motor Attached
Replacing the Movable Cutter Blade
Replacing the Controller Board
Replacing the Encoder
Adjusting the Encoder
Replacing the Brush
Replacing the Thermostat Assembly
Replacing the Solenoid Spring
Replacing the Top Roller
Replacing the Free Spin Roller Assembly
Replacing the Ramp
Replacing the Tape Guide Assembly
Replacing the Fixed Blade
Replacing the Front Cover
Replacing the Feed Wheel
Replacing the Solenoid
Replacing the Motor
Parts List
Wiring Diagram
Addendum
Removing the Weighted Brush Cover
Attaching the Weighted Brush Cover
75 Correctly routing the tape and pressure plate
76Properly positioning the fixed blade holder
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
4
Introduction
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
Telephone:
(618)-343-1006
Fax:
(618)-343-1016
E-mail:
Website:
www.msscllc.com
Congratulations on the purchase of your new MARSH TD2100 gummed tape dispenser
from MARSH SHIPPING SUPPLY CO., LLC. We are confident you will be very pleased
with the operation and performance of this durable, quality built machine for many years
to come.
The TD2100 Electric Taper Technical Manual provides the necessary information about
the operation, maintenance, and repair of your new tape dispenser. However, Marsh
does have a policy of continual product improvement. So, Marsh reserves the right to
modify the information contained within the manual without prior notice.
The setup section was designed to simplify the setup of the machine and allow you to get
the machine up and running so that the machine can do what it is designed to do…
dispense gummed tape quietly, quickly and accurately.
The operating section provides information on the operation of the machine, i.e. keystroke
operation, programming repeat lengths, etc.
The maintenance section provides information about required care and maintenance of
the machines and further adjustments if required for your particular use.
This technical manual provides a troubleshooting and repair sections to help you with
possible operating problems and corrective actions. Should you require replacement
parts, please refer to the providedparts list and the corresponding exploded view
drawings.
For assistance, or if you would like to obtain information about any Marsh product,
contact your Marsh distributor or Marsh Shipping Supply Company, LLC at:
Marsh Shipping Supply Company, LLC
Address: 926 McDonough Lake Road
Collinsville, IL 62234 USA
5
Specifications
Net and Shipping Weight
:
26 pounds (11.8 kg); 32 pounds (14.5 kg)
Water Bottle Capacity: 70 ounces (2070 ml)
Tape: Dry gummed tape – paper or reinforced – between 1 to 3
inches (25.4 to 76.2 mm) wide, up to 1000 feet (304.8 m) long
and 9 (228.6 mm) inches max roll diameter
Electrical Requirements: 115 volts AC or 220 volts AC
50/60 Hz
4 amps at 115 volts
2 amps at 220 volts
Power Cord Length: 7 feet (2.3 m)
Dimensions:
Figure 1 – Tape Machine Dimensions
10.1 in
25.5 cm
11.9 in
30.1 cm
18.9 in
48.0 cm
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
6
Loading Tape
–
refer to
Figure
s
2 & 3
1. Open the top cover of the machine.
2. Adjust the tape guides, with the tape guide turnbuckle, wide enough to get the tape
between them.
3. Place the roll of tape into the machine.
4. Adjust the tape guides, with the tape guides turnbuckle, to hold the tape in the middle of
the machine with a 1/8” clearance on both sides.
5. Remove the pressure plate from the machine.
6. Feed the tape, gummed side down, over the top roller, under the tape guide flaps, and
then under the pinch roller, see Figure 3.
NOTE: For gummed side out tape (typically used in Europe), load the tape roll opposite
as shown and route the gummed side over the top roller.
7. Place the pressure plate over the tape and release the pinch roller.
8. Close the top cover.
Setup Instructions
Figure 2 – Loading Tape
Turnbuckle
Tape Guide Flap
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
7
Figure 4 – Filling the Water Bottle, Adjusting the
Brush Tank Water Level, Adjusting the Tape Weight
Figure 3 – Tape Routing
Duckb
ill
Valve
Water Bottle
Brush
Tank
Post
Retaining
Screw
Tape Weight
Water Bottle
Brackets
Pinch
Roller
Roll of Tape
Top Roller
Tape
Cutter
Pressure
Plate
Gummed Side Out Tape
Cleaning Gaps
Turnbuckle
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
8
Figure 5 – Adjustable Water Level Positions
Adjusting the Brush Tank Water Level – refer to Figures 4 and 5
1. Loosen the retaining screws on the water bottle brackets.
2. Move the water bottle brackets to the desired position to obtain the
desired water level in the brush tank, light weight tapes would
typically be set at the low position, Figure 5.
3. Both brackets should be at the same position.
4. Tighten the retaining screws on the water bottle brackets.
Adjusting the Tape Weight – Figure 4
1. Loosen the retaining screw.
2. Slide the tape weight forward for greater pressure, typically heavy
weight tapes which will apply more water on the tape.
3. Slide the tape weight backwards less pressure, typically light weight
tapes which will apply less water on the tape.
4. Tighten the retaining screw.
Filling the Water Bottle – Figure 4
1. Remove the water bottle from the machine.
2. Remove the duckbill valve from the water bottle.
3. Fill the water bottle with water.
4. Place the duckbill valve back into the water bottle.
5. Place the water bottle back onto the machine; verify that the post in the
brush tank is inserted through the duckbill valve.
Low
Medium
High
Water bottle bracket
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
9
Operating Instructions
Standard Keypad
Pre-Programmed Lengths and SHIFT – There are 20 common lengths of tape pre-
programmed into the memory of your TD2100 automatic tape dispenser. Simply press
one of the ten length keys and the length in black is dispensed. To dispense the lengths
in red press the SHIFT key then press the corresponding length key.
REPEAT SHORT and REPEAT LONG – It is possible to store any of the 20 pre-
programmed lengths into the convenient REPEAT SHORT or REPEAT LONG keys.
To do so, press PROGRAM, the desired length (red lengths require SHIFT key to be
pressed first) and then the REPEAT SHORT or REPEAT LONG your preference.
While in PROGRAM MODE no tape is dispensed, display flashes, and flashing stops
when programming is completed or PROGRAM is pressed to cancel mode.
RANDOM – The RANDOM key allows the user to dispense tape while pressed and the
machine will cut the tape when the RANDOM key is released.
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
10
TD2100 PREMIUM Keypad
- The Premium keypad offers all the same function as the
STANDARD keypad plus it is possible for you to dispense any length of tape from 5”
to 99” in 1” increments. The exception from the STANDARD keypad is there are 10
preset lengths versus 20. There are two versions of the PREMIUM keypad, Short and
Long. The Long version has longer pre-programmed lengths than the Short.
To dispense a length of tape 5” to 99” press the NUM LOCK key. The NUM LOCK
light is lit and the 0-9 keys are activated. Just press any two keys to get the desired
length. For example, press 07 for 7” piece of tape or 77 for a 77” piece of tape. These
“custom” lengths can be programmed in the REPEAT SHORT or REPEAT LONG
keys by turning on the NUM LOCK, press PROGRAM, press two keys of desired
length and then desired REPEAT key to store value. You must turn off the NUM
LOCK mode to verify the length is stored and displayed.
Marsh Shipping Supply Co., LLC. Collinsville, IL 62234 U.S.A. | Tel: 618.343.1006 | Fax: 618.343.1016 42901 09/21/2016
Other manuals for TD2100
3
Table of contents
Other Marsh Dispenser manuals
Popular Dispenser manuals by other brands
Silver King
Silver King Majestic SK12MAJ Technical manual and replacement parts list
Franke
Franke F3Dn Twin Service manual
STIEBEL ELTRON
STIEBEL ELTRON UltraHot Plus Operation and installation instructions
DAN DRYER
DAN DRYER 282 installation guide
Essity
Essity Tork 473208 manual
CBS
CBS SD300BU-88 COMPONENT MAINTENANCE MANUAL WITH ILLUSTRATED PARTS LIST
