MAPro VMX Three60 User manual
Marpo Kinetics, Inc.
258 LINDBERGH AVE, Livermore, A 94551 • (925) 606-6919 • www.marpokinetics.com
- VMX Three60 –
IMPORTANT
INFORMATION
TO SAFELY REMOVE PRODUCT
FROM THE PACKAGE,
FOLLOW THESE INSTRUCTIONS
FOR SAFETY, TWO OR MORE PEOPLE MUST ASSIST IN THE PACKAGE
REMOVAL AND PRODUCT INSTALLATION
IT IS BEST THAT THE REMOVAL OF THE PRODUCT FROM THE PACKAGE, BE
DONE NEAR THE AREA WHERE THE PRODUCT WILL BE PLACED FOR USE
THIS WILL ELIMINATE THE NEED TO MOVE THE PRODUCT AROUND AFTER
IT IS ASSEMBLED SHOULD THERE BE A NEED TO MOVE THE PRODUCT,
THERE MUST ALWAYS BE AT LEAST TWO PEOPLE DOING THIS OPERATION
TO AVOID ANY INJURIES TO PROTECT THE ROPE FROM SNAGS, IT MUST BE
KEPT WRAPPED UNTIL IT IS READY TO BE STRETCHED ONTO THE PULLEYS
REMEMBER, ALWAYS KEEP ALL BODY PARTS AWAY FROM PULLEYS OR ANY
MOVING PARTS AS THESE ELEMENTS CAN CAUSE SERIOUS INJURY
MINORS SHOULD NEVER BE ALLOWED TO OPERATE THE MACHINE WITHOUT
THE CONSENT AND CONSTANT SUPERVISION OF AN ADULT
Securing Equipment
All MARPO equipment must be secured to the floor to stabilize and eliminate rocking or
tipping This must be performed by a licensed contractor DO NOT use the equipment if it
is not set up and located on a solid, level surface
DO NOT install equipment on an uneven surface.
Use fasteners having a minimum of 500 lbs tensile capacity (3/8" grade 2 bolts or better)
If legs/frame does not contact surface, DO NOT pull down with anchors Shim any leg or
frame not in contact with surface using flat washers
1
Marpo Kinetics, Inc.
258 LINDBERGH AVE, Livermore, A 94551 • (925) 606-6919 • www.marpokinetics.com
1. Remove all wrapping material.
CAUTION: Do not use blades to cut wrapping material since it may damage the unit.
2. Remove all contents from each box:
1 MA N UN T
1 BOOM
1 CARR AGE
1 BOOM CAP
1 CROSS BAR
1 SET (LEFT AND R GHT) COVERS FOR BOOM BASE
1 JO NT NG BOX/STEP (PER STAT ON)
1 REAR JO NT NG LEG (PER STAT ON)
1 BOTTOM ROPE PULLEY (W TH BRACKET)
1 USER MANUAL
1 PACKAGE REMOVAL NSTRUCT ON
1 WORKOUT POSTER
2
Marpo Kinetics, Inc.
258 LINDBERGH AVE, Livermore, A 94551 • (925) 606-6919 • www.marpokinetics.com
3. One person should hold on to the MA N UN T while a second person should attach the
CROSS BAR using the provided 1/4-20 X 3” screws. Use a cardboard block provided
with the unit to prop up the unit while attaching the M D CROSS BAR. Have a second
person hold the unit from falling over while attaching the M D CROSS BAR. The anti-
skid tape of the M D CROSS BAR should be pointing to the ground. nsert screws with
1” OD fender washer from the bottom up through the M D CROSS BAR so the threads
protrude from the M D CROSS BAR upwards. Fasten provided 0.25-20 nut onto
protruding thread.
CAUTION: Leaving the product unsupported before the unit is attached to the
CROSS BAR could cause the unit to fall over and cause injury and/or product
damage
4. For all three units attach the BOTTOM ROPE PULLEY (W TH BRACKETS) to the
MA N UN T. Screws are temporarily attached to the frame of the MA N UN T.
5. Attach the units to the REAR JO NT NG LEG. The 1” OD fender washers go up against
the head of the screws. nsert screws from the bottom up so the threads protrude
upwards. Do not fully tighten the screws for now.
6. Attach the JO NT NG BOX to all 3 units starting with the center unit. The black and
yellow safety tape on the JO NT NG BOX must point up to serve as a step on surface.
When attaching the two outside units to the JO NT NG BOX you may need to reposition
the center unit until all three units touch the wall of the box. Afterwards, tighten all
screws on JO NT NG BOX and REAR JO NT NG LEG.
7. nstall the CARR AGE in the BOOM. To install the CARR AGE, slide the 4 metal
rollers of the CARR AGE inside the two barrels of the BOOM. Note the CARR AGE
PULLEY orients to the front of the unit. Remove the pulley from the CARR AGE and
install the rope on it. Make sure rope is not twisted when installing on the CARR AGE.
Afterwards, attach BOOM CAP to BOOM and slide carriage to the bottom slot in the
BOOM before proceeding.
8. Connect the BOOM to the MA N UN T with the 3/8-16 bolts, nuts and washers.
3
Marpo Kinetics, Inc.
258 LINDBERGH AVE, Livermore, A 94551 • (925) 606-6919 • www.marpokinetics.com
9. Connect PLAST C COVERS for Boom Base. Using provided hardware, fasten small
covers to the main covers, then fasten the top of the small cover to the boom.
The electronic display works with two AAA batteries. To replace the batteries, remove
the 4 screws that connect the D SPLAY TRAY to the main covers. Slowly pull the
D SPLAY TRAY away from the machine. Disconnect the display from the main
harness. To access the battery cover on the back of the D SPLAY remove the 4 machine
screws that connect the D SPLAY to the the D SPLAY TRAY.
4
Boom
Cap
Carriage
Handle
Boom
connection
Plastic Covers for
Boom Base
Marpo Kinetics, Inc.
258 LINDBERGH AVE, Livermore, A 94551 • (925) 606-6919 • www.marpokinetics.com
10. Once the machines have been leveled off with the ground, drill the anchor rods provided
with the user manual at the specified locations in the picture below. Anchor rods must be
drilled into the concrete with a minimum embedment length of 2" for optimal
performance.
5
Anchor rod minimum
embedment length: 2”
Table of contents
