Manitou Mattoc User manual
MATTOC TRAVEL ADJUST MANUAL
2
Table of Contents
Secon Page Number
Introducon & Required Tools 3-4
Secon 1 - Fork Disassembly 5-9
Secon 2 - Travel Adjust, 26” Forks 10
Secon 3 - Travel Adjust, 27.5” Fork 11
Secon 4 - Fork Assembly 12-17
Hayes Components USA
5800 W. Donges Bay Rd.
Mequon, WI 53092
Tel: 888.686.3472
Email: techsupport@hayesbicycle.com
Web: www.hayescomponents.com
Hayes Components Europe
Dirnismaning 20 a
85748 Garching (b. Munich)
Germany
Email: techsupportEU@hayesbicycle.com
Web: www.hayescomponents.com
3
MATTOC TRAVEL ADJUST MANUAL
INTRODUCTION
This manual is intended to guide the user through the steps necessary to internally adjust
the travel of the Maoc Pro and Expert forks. NOTE: This manual does not cover the
steps need to convert the fork from one wheel size to another. Please see the Maoc
Service Guide for instrucons on how to perform this.
Suspension forks by design can contain preloaded springs, gases and
uids under extreme pressures. Warnings contained in this manual must be observed to
avoid damage to fork, serious injury or even death.
We highly recommend that service to this fork be performed by a
cered bicycle mechanic. Failure to follow instrucons presented in this manual could
lead to serious injury or death. Any quesons about the servicing of this fork or the
manual itself should be directed to Manitou Customer Support at:
Phone: 888-686-3472
Email: techsupport@hayesbicycle.com
MATTOC TRAVEL ADJUST MANUAL
4
Below is a list of tools necessary for changing the travel of the Maoc fork.
Safety Glasses
Nitrile Gloves
Lint-Free Rags
Torque Wrench
Slickoleum™ Grease
Semi-bath Oil, 5/40w Synthec Oil - Manitou part number 85-0023
Maoc Service Tool Kit - Manitou part number 172-31133
This kit contains all tools below for servicing the Maoc fork:
- Maoc 8mm Thin Wall Socket
- Maoc Cassee Tool
- Maoc Flat Ground 24mm Socket
8mm Allen Wrench
8mm Allen Socket
2mm Allen Wrench
2mm Allen Socket
3mm Allen Wrench (oponal)
4mm Allen Wrench (oponal)
Fork/Shock Pump
REQUIRED TOOLS
5
MATTOC TRAVEL ADJUST MANUAL
SECTION 1 - FORK DISASSEMBLY
1. Remove air valve cap.
2. Using a 2mm Allen wrench, remove
the rebound damper knob.
1
2a
2b
MATTOC TRAVEL ADJUST MANUAL
6
3. Insert an 8mm Allen wrench into the
end of the rebound damper rod. Turn
wrench clockwise unl damper rod can
be pushed into fork casng.
3a
3b
3c
7
MATTOC TRAVEL ADJUST MANUAL
4. Using the Maoc 8mm Thin Wall Socket,
turn the compression rod clockwise unl
compression rod is disengaged from the
casng threads.
4
5. Remove casng from the fork. It is
recommended that this be done over a
drain pan as there is semi-bath oil in the
lower legs that will be released when
casng is removed.
5
6. Aach shock pump to the air valve on
the compression rod and use the pressure
release buon to release all air pressure
from the fork. If your shock pump does not
have a pressure release on it you can use
a 3mm Allen wrench to depress the valve
core and release the air.
Air pressure must be released
prior to disassembly of the fork. Failure to
properly and fully release air pressure could
result in serious injury or death.
6
MATTOC TRAVEL ADJUST MANUAL
8
7. With shock pump sll aached and
pressure release buon depressed,
compress the compression rod assembly
into the upper stanchion of the fork.
Compress rod unl boom out bumper is
contacng the end cap. If your shock pump
does not have a pressure release buon use
a 3mm Allen wrench to depress the valve
core while pushing compression rod into
stanchion.
8. Place Maoc Cassee Tool into the
compression rod assembly end cap.
9. Using an adjustable wrench or similar
tool, turn the cassee tool counter
clockwise to remove compression rod
assembly from fork stanchion.
7
8
9
9
MATTOC TRAVEL ADJUST MANUAL
10. Remove compression rod assembly
from fork.
11. Using the Maoc 24mm Flat Ground
Socket slowly remove the air cap from the
fork.
NOTE: A standard socket can be used as
well however the rounded edges of a
standard socket can cause the socket to
jump o of the air cap while turning causing
cosmec damage to the fork.
10a
10b
11a
11b
MATTOC TRAVEL ADJUST MANUAL
10
SECTION 2 - TRAVEL ADJUST, 26” FORKS
The below photos show the dierent travels achievable on the Maoc 26” forks by
adding and removing the travel spacers on the compression rod assembly. Travel
spacers are boxed in yellow below for reference. When seng the fork at 170mm you
will remove all travel spacers from the compression rod.
140mm
150mm
160mm
170mm (26” forks only!)
Table of contents
Other Manitou Bicycle Accessories manuals
Manitou
Manitou Mara Pro User manual
Manitou
Manitou Jack SL Dropper Seat Post User manual
Manitou
Manitou LUXE COMP User manual
Manitou
Manitou MARA PIGGYBACK User manual
Manitou
Manitou DORADO EXPERT 37MM User manual
Manitou
Manitou Axel Super 2004 User manual
Manitou
Manitou XVERT R User manual
Manitou
Manitou Mezzer Pro User manual
Manitou
Manitou R7 EXPERT User manual
Manitou
Manitou DORADO User manual
