M-system R8-FS16N User manual

R8-FS16N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9791 P. 1 / 5

DC CURRENT / VOLTAGE INPUT MODULE

(built-in excitation /16points, non-isolated)MODEL R8-FS16N

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

DC current / voltage input module......................................(1)

■MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•The equipment must be mounted inside a panel.

•The actual installation environments such as panel con-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrat-

ed in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■GENERAL PRECAUTIONS

•Before you remove or mount the unit, turn off the power

supply and input signal for safety.

•Do not touch the connector while power is on. The unit

may have a malfunction due to static electricity etc.

•Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ENVIRONMENT

•Indoor use

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

•Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to90% RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■EXCITATION SUPPLY

•Rated curent 3 A DC (rated current 3 A for internal fuse

(slow blow fuse i2t (A2sec) max. 5.04)

■AND ....

The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for sat-

isfying complete performance described in the data sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Conﬁrm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning

the grooves of both modules (A & B in the above ﬁgure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R8-FS16N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9791 P. 2 / 5

• Protective Cover

Groove

Hook

The protective cover is to be attached over the connected

I/O module

at the right end.

Align the hooks on the cover with the grooves of the module

and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the

hooks inward.

■HOW TO UNMOUNT THE MODULE ON DIN RAIL

Release the locking clamps and pull out straight the mod-

ule.

• Removing an intermediate module

Caution !

1 ) Be careful not to hurt your hand by pointed edges of

the internal communication bus connector.

2 ) I/O modules cannot hold tightly on the DIN rail by

themselves without power/network module.

Secure them to the position if necessary by using DIN

rail end plates.

R8-FS16N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9791 P. 3 / 5

COMPONENT IDENTIFICATION

Function Setting

DIP SW

Input Connector

Voltage / Current

DIP SW

SW1 SW2

■FRONT VIEW ■SIDE VIEW

RUN

39 40

Internal Bus Connector

Status Indicator LED

Input Status Indicator LEDs

Internal Bus Connector

■INDICATOR LED

LED

OPERATION

FUNCTION

Status OFF Stopping

Green ON Valid host communication

Green Blinking

Reading/writing conﬁguration

Red ON Setting error

Red Blinking Parameter error

Input

Status

OFF Input data in the range

Red Blinking Input data out of range

■PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgu-

rator Software (model: R8CFG):

•Input setting by channels (setting value, scaling, zero/

gain adjustments, selecting current/voltage)

•Common setting (loss of internal bus communication de-

tection time)

Programming by the PC Conﬁgurator is available via the

Power/Network Module.

Refer to the users manual for the R8CFG for detailed opera-

tion of the software program.

■MODULE ADDRESS

SW 1-1 through 1-4 determine the tenth place digit, while

SW 1-5 through 1-8 do the ones place digit of the address.

Address is selected between 0 to 24.

(Factory setting: 0)

MODULE

ADDRESS

SW1

x10 1234

x1 5 6 7 8

0 OFF OFF OFF OFF

1 OFF OFF OFF ON

2 OFF OFF ON OFF

3 OFF OFF ON ON

4 OFF ON OFF OFF

5 OFF ON OFF ON

6 OFF ON ON OFF

7 OFF ON ON ON

8 ON OFF OFF OFF

9 ON OFF OFF ON

■OPERATING MODE

(*)Factory setting

• Terminator DIP SW

TERMINATOR SW SW2

Without (*) OFF

With ON

Note: SW 2-1 through 2-4 and SW 2-4, 5, 7, 8 are unused. Be sure to set

unused SWs to OFF.

• Voltage / Current DIP SW

For voltage input, set the switch OFF.

For current input set the switch ON.

Note: To conﬁgure the input, setting from conﬁgurator software and the

setting of this switch are required.

R8-FS16N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9791 P. 4 / 5

■INPUT CONNECTOR ASSIGNMENT

39 40

NO. ID FUNCTION

1In 1 Input 1 (+)

2Input 1 (−)

3In 2 Input 2 (+)

4Input 2 (−)

5In 3 Input 3 (+)

6Input 3 (−)

7In 4 Input 4 (+)

8Input 4 (−)

9In 5 Input 5 (+)

10 Input 5 (−)

11 In 6 Input 6 (+)

12 Input 6 (−)

13 In 7 Input 7 (+)

14 Input 7 (−)

15 In 8 Input 8 (+)

16 Input 8 (−)

17 In 9 Input 9 (+)

18 Input 9 (−)

19 In 10 Input 10 (+)

20 Input 10 (−)

21 In 11 Input 11 (+)

22 Input 11 (−)

23 In 12 Input 12 (+)

24 Input 12 (−)

25 In 13 Input 13 (+)

26 Input 13 (−)

27 In 14 Input 14 (+)

28 Input 14 (−)

29 In 15 Input 15 (+)

30 Input 15 (−)

31 In 16 Input 16 (+)

32 Input 16 (−)

33, 34

35, 36 24V Excitation supply 24V

37, 38

39, 40 0V Excitation supply 0V

CONNECTION DIAGRAM

INTERNAL POWER

INTERNAL BUS

EXC. SUPPLY

−

INPUT 1

−

INPUT 2

−

INPUT 3

−

INPUT 4

−

INPUT 5

−

INPUT 6

−

INPUT 7

−

INPUT 8

−

INPUT 9

−

INPUT 10

−

INPUT 11

−

INPUT 12

−

INPUT 13

−

INPUT 14

−

INPUT 15

−

INPUT 16

+24V

BUS CONNECTOR

R8-FS16N

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9791 P. 5 / 5

EXTERNAL DIMENSIONS unit: mm (inch)

115(4.53)

6(.24)

7(.28)6(.24)7(.28)

[3(.12)] [4(.16)]

24(.94)[75(2.95)]

55(2.17)

DIN RAIL (35 mm wide)

WIRING INSTRUCTIONS

■MIL connector

PWB connector XG4A-4034 (Omron)

Recommended socket XG5N-401 (Omron)*1

Recommended contact XG5W-0231 (Omron)*1

Applicable wire size: : AWG22, 17 strands, (0.16 dia)

*1) Not included in the package. Refer to the speciﬁcations of the product.

Table of contents

Other M-system Control Unit manuals

M-system

M-system R7L-EC16B User manual

M-system

M-system R7M-EA16 User manual

M-system

M-system Devicenet R7F4HD-DAC32D User manual

M-system

M-system R3-SV8C User manual

M-system

M-system 73VR3100 User manual

M-system

M-system R6-NP1 User manual

M-system

M-system R7M-SV4-R User manual

M-system

M-system R7ML-DC16D User manual

M-system

M-system R7M-YS2 User manual

M-system

M-system R7M-EC8B/UL User manual

M-system

M-system R3-ND1 User manual

M-system

M-system R1M-A1 User manual

M-system

M-system R7C-DC16A User manual

M-system

M-system R3-NC2 User manual

M-system

M-system R7L-EC8B User manual

M-system

M-system R5-NM1 User manual

M-system

M-system R7C-RS4 User manual

M-system

M-system R7ML-EC16A User manual

M-system

M-system R7ML-YV2-R User manual

M-system

M-system R3-NMW1F User manual

M-system

M-system R6S-RS2 User manual

M-system

M-system EtherCAT R30GECT1 User manual

M-system

M-system R7 Series User manual

M-system

M-system R3-SV4B User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual