M-system R8-DCM16ALK User manual

R8-DCM16ALK

P. 1 / 5EM-9747 Rev.2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

NPN TRANSISTOR OUTPUT MODULE

(16 points, full and individual interlock) MODEL

R8-DCM16ALK

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

contents of the package you received as below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Transistor output module ..............................................(1)

■MODEL NO.

Conﬁrm that the model number described on the product is

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

•Theequipmentmustbemountedinsideapanel.

•

The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may affect

the protection level of this unit when it is integrated in

a panel system. The user may have to review the CE re-

quirements in regard to the whole system and employ ad-

ditional protective measures to ensure the CE conformity.

■GENERAL PRECAUTIONS

•Beforeyouremoveormounttheunit,turnoffthepower

supply and I /O signal for safety.

•Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ ENVIRONMENT

•Indooruse

•Whenheavydustormetalparticlesarepresentintheair,

install the unit inside proper housing with sufﬁcient ven-

tilation.

•Donotinstalltheunitwhereitissubjectedtocontinuous

vibration. Do not apply physical impact to the unit.

•Environmentaltemperaturemustbewithin-10to+55°C

(14to131°F)withrelativehumiditywithin30to90%RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■EXCITATION SUPPLY

•Inputconnector:Ratedcurent50mADCperchannel

•Outputconnector:Ratedcurent3ADC(ratedcurrent3A

for internal fuse (slow blow fuse i2t(A2sec)max.5.04)

■AND ....

•Theunitisdesignedtofunctionassoonaspowerissup-

plied,however,awarmupfor10minutesisrequiredfor

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Confirm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning the grooves of

both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R8-DCM16ALK

P. 2 / 5EM-9747 Rev.2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

■HOW TO MOUNT THE MODULE ON DIN RAIL

Release the locking clamps and pull out straight the module.

Caution !

1) Be careful not to hurt your hand by pointed edges of the internal

communication bus connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

R8-DCM16ALK

P. 3 / 5EM-9747 Rev.2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

COMPONENT IDENTIFICATION

OUT

19 20

IL ALL

IL1

IL2

SW1 SW2

SW3

SW5

SW4

SW7 SW6

X10 X1

SW9 SW8

RUN

Full Interlock

Indicator LED

Full interlock

Connector

Function Setting

DIP SW

Status Indicator LED

Discrete Output Indicator LED

Internal Bus Connector

Output Connectors

Full Interlock

Function Setting

DIP SW

Individual Interlock

Function 1 Setting

DIP SW

Individual Interlock

Function 2 Setting

DIP SW

FRONT VIEWLEFT SIDE VIEW RIGTH SIDE VIEW

Individual Interlock 1

Indicator LED

Individual Interlock 1

Connector

Individual Interlock no.

Setting Rotary SW

Individual Interlock 2

Indicator LED

Individual Interlock 2

Connector

■INDICATOR LED

LED

OPERATION

FUNCTION

Status OFF Stopping

Green ON Valid host communication

Green Blinking

Reading/writingcongura-

tion

RedON Setting error

RedBlinking Parameter error

Output OFF OFF

Green ON ON

Interlock OFF Interlock invalid

Interlock valid

Output ON

RedON Interlock valid

OutputOFF

■INPUT CONNECTOR ASSIGNMENT

PIN ID FUNCTION

No.

1 24V Excitation supply 24 V

2 IL Discrete input

3 0V Excitation supply 0 V

4 NC No connection

■OUTPUT CONNECTOR ASSIGNMENT

1 Do1 Output 1

2 Do2 Output 2

3 Do3 Output 3

4 Do4 Output 4

5 Do5 Output 5

6 Do6 Output 6

7 Do7 Output 7

8 Do8 Output 8

9 Do9 Output 9

10 Do10 Output 10

11 Do11 Output 11

12 Do12 Output 12

13 Do13 Output 13

14 Do14 Output 14

15 Do15 Output 15

16 Do16 Output 16

17, 18 0V Excitation supply 0V

19, 20 24V Excitation supply 24V

PIN ID FUNCTION

No.

R8-DCM16ALK

P. 4 / 5EM-9747 Rev.2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

■MODULE ADDRESS

ModuleaddresscanbesetwithSW1-1through1-4forthe

tens,andSW1-5through1-8fortheonesplacedigit.

Addressisselectedbetween0to31.(Factorysetting:0)

MODULE ADDRESS

SW1

0 OFF OFF OFF OFF

1OFF OFF OFF ON

2OFF OFF ON OFF

3OFF OFF ON ON

4OFF ON OFF OFF

5 OFF ON OFF ON

6OFF ON ON OFF

7OFF ON ON ON

8ON OFF OFF OFF

9ON OFF OFF ON

■OPERATING MODE

*Factorysetting

• Interlock Communication Logic Reversal

Setting internal communication bus logic.

INTERLOCK COMMUNICATION LOGIC REVERSAL SW2-1

Interlockfunctionsettingoff:1

Interlockfunctionsettingon:

normal=1,interlock=0

Interlockfunctionsettingoff:0(*)

Interlockfunctionsettingon:

normal=0,interlock=1

OFF

Caution:1and0valuesarevalidatedaslogicthroughinternal

communication bus logic.

• Output at The Loss of Communication

Setting for all output.

OUTPUT AT THE LOSS OF COMMUNICATION SW2-5

OutputHold(*)

(last data correctly rerceived is hold

OFF

Stopoutput(OutputxedatOFF) ON

• Terminator DIP SW

TERMINATOR SW SW2-6

Without(*) OFF

With ON

• Conguration Mode

CONFIGURATION MODE SW2-8

DIP switch setting (*) OFF

PC Conﬁgurator and communicaton ON

Caution:SW2-2through2-4and2-7areunused;besuretoturn

OFFunusedchannels.

■FULL INTERLOCK FUNCTION

It is available to apply full interlock function to all outputs

(Do1 through Do16)

FULL INTERLOCK FUNCTION SW3-1

OFF OFF

ON(*)(alloutputsOFFifinputOFF) ON

Caution:SW3-2isunused;be suretoturn OFFunused chan-

nels.

■INDIVIDUAL INTERLOCK

At output, it is available to apply interlock function to 2

points arbitrary.

• Individual interlock function 1

INDIVIDUAL INTERLOCK 1 SW4-1

SW6,7OFF OFF

SW6,7ON(*)

(InputOFFwithoutputOFF) ON

• Individual interlock function 2, channel

INDIVIDUAL INTERLOCK 1

CHANNEL

SW6 SW7

Ones Tens

ON 01through16

OFF 00,17through99

• Individual interlock function 2

INDIVIDUAL INTERLOCK 2 SW5-1

SW8,9OFF OFF

SW8,9ON(*)

(InputOFFwithoutputOFF) ON

• Individual interlock function 2, channel

INDIVIDUAL INTERLOCK 2

CHANNEL

SW8 SW9

Ones Tens

ON 01through16

OFF 00,17through99

Caution:SW4-2and5-2 areunused;be suretoturnOFF un-

used channels.

■PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgu-

ratorSoftware(model:R8CFG):

•Outputatthestartup

•Outputatthelossofcommunication

•Commonsetting(lossofinternalbuscommunicationde-

tection time)

TurnSW2-8ONtoallowprogrammingbythePCCongu-

rator via the Power / Network Module.

RefertotheusersmanualoftheR8CFGfordetailedopera-

tion of the software program.

R8-DCM16ALK

P. 5 / 5EM-9747 Rev.2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EXTERNAL DIMENSIONS unit: mm (inch)

24 (.94) [75 (2.95)]

115 (4.53)6 (.24)7 (.28) 6 (.24) 7 (.28)

DIN RAIL

(35 mm wide)

[3 (.12)] [4 (.16)]

55 (2.17)

CONNECTION DIAGRAM

INTERNAL POWER

INTERNAL BUS

EXC. SUPPLY

Do 1

Do 2

Do 3

Do 4

Do 5

Do 6

Do 7

Do 8

Do 11

Do 12

Do 13

Do 14

Do 15

Do 16

24V

Do 9

Do 10

BUS CONNECTOR

IL ALL FULL INTERLOCK

IL 1 INDIVIDUAL INTERLOCK 1

IL 2 INDIVIDUAL INTERLOCK 2

24V

IL ALL

24V

IL1

24V

IL2

Detecting

Circuit

Detecting

Circuit

Detecting

Circuit

WIRING INSTRUCTIONS

■e-CON connector (discrete input)

PWBconnectorXN2D-1474-S002(Omron)

RecommendedcableconnectorXN2A-1470(Omron)*1

Applicablewiresize:0.08mm2(AWG28)-0.5mm2(AWG20)

(Outersheathdiameter:max.1.5dia)

■MIL connector (discrete output)

PWBconnectorXG4A-2034(Omron)

RecommendedsocketXG5N-201(Omron)*1

RecommendedcontactXG5W-0231(Omron)*1

Applicablewiresize:AWG22,number ofconductor 17, di-

ameterofconductor0.16mm

*1.Notincludedinthepackage.Refertothespecications

of the product.

Table of contents

Other M-system Control Unit manuals

M-system

M-system R5T-DA4 User manual

M-system

M-system R3-PT4 User manual

M-system

M-system R7M-RS4 User manual

M-system

M-system R80FST4NJ User manual

M-system

M-system R3-ND1 User manual

M-system

M-system R7C-YS2 User manual

M-system

M-system R7L-SV4-R User manual

M-system

M-system R3-NMW1F User manual

M-system

M-system R7HL-YS2 User manual

M-system

M-system R7C-DC16A User manual

M-system

M-system R7D-DA16 User manual

M-system

M-system R7M-SV4-R User manual

M-system

M-system R3-NC3 User manual

M-system

M-system MECHATROLINK R7K4FML3-6-DAC32B User manual

M-system

M-system R7E-EA8 User manual

M-system

M-system R3Y-PA16 User manual

M-system

M-system R3-PD16 User manual

M-system

M-system R7ML-YV2-R User manual

M-system

M-system R7L-YV2 User manual

M-system

M-system EtherCAT R30GECT1 User manual

M-system

M-system R8-DCM16ALH User manual

M-system

M-system R30US2 User manual

M-system

M-system 73VR3100 User manual

M-system

M-system R7C-RS4 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual