M-system R3-NP1 User manual

R3-NP1

P. 1 / 4EM-8418 Rev.3

PROFIBUS-DP INTERFACE MODULE MODEL R3-NP1

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Network interface module............................................ (1)

■ MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■ CONFORMITY WITH EC DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices and connected wires may

affect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure CE conformity.

■ POWER INPUT RATINGS

Operational range & power consumption: Check the power

rating for the unit on the speciﬁcation label.

Rating 100 – 120V AC: 85 – 132V, 47 – 66 Hz, approx. 20VA

Rating 200 – 240V AC: 170 – 264V, 47 – 66 Hz, approx. 20VA

Rating 24V DC: 24V

10%, approx. 12W

■ UNPLUGGING THE MODULE

Before you remove the module from its base or mount it,

turn off the power supply for safety.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufﬁcient ven-

tilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output)

close to noise sources (relay drive cable, high frequency

line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■ AND ....

The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for sat-

isfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base Model R3-BSx, or Model R3-

BSWx for free I/O address capability.

Before mounting the Network Interface Module onto the

Base, be sure to conﬁgure the module as explained below.

■ NODE ADDRESS

See “COMPONENT IDENTIFICATION.”

■ NETWORK SLOTS ON THE BASE

With Model R3-BSx base, mount the I/O Modules from the

left end (I/O 1) to the right in order that the Network Mod-

ule assigns data areas from I/O 1.

Network Module(s) and Power Module are mounted basi-

cally at the right end though technically they could be

mounted in any position.

With Model R3-BSWx base, there is no limitation in mount-

ing positions as I/O address can be assigned freely to each

module using rotary switches equipped on the base.

I/O 1 I/O 2 I/O n

R3-NP1

P. 2 / 4EM-8418 Rev.3

COMPONENT IDENTIFICATION

SW3

SA1

SA2

RUN LED

■ FRONT VIEW ■ SIDE VIEW

ERR LED

Configuration Jack

Node Address Setting

Rotary SW, upper digit

Node Address Setting

Rotary SW, lower digit

Network Connector

■ PROFIBUS INTERFACE

PIN NO. SIGNAL SIGNIFICANCE

B_line

Not used

Network, B-line

RTS

GND

P5V

RTS signal

A_line

Not used

Network, A-line

Not used

■ FRONT ROTARY SW

• Node Address: SA1, SA2

Node Address is set in Hexadecimal.

■ SIDE DIP SW

• Dual Communication: SW3

When two network modules are mounted, one must be

‘Main’ (OFF) network and the other must be ‘Sub’ (ON) net-

work. For single communication, the network module must

always be set to ‘Main’ (OFF).

SW DUAL COMMUNICATION

MAIN (*) SUB

SW3-1 OFF ON

• Input Error Data: SW3

Hold: When the communication from an input module is lost

due to the input module error, the network module holds the

signal and stands by until the communication recovers.

Set to ‘0’: When the communication from an input module

is lost due to the input module error, the network module

outputs ‘0.’

SW INPUT ERROR DATA

HOLD (*) SET ‘0’

SW3-2 OFF ON

• LED Function: SW3

Functions assigned to the front RUN and ERR LEDs can

be selected.

When SW3-4 is OFF: R3 Network Status (*)

RUN ERR EXPLANATION

Green ON OFF Normal (Data_Exchange)

Green ON Green Flash External Diagnostics

OFF Green ON Error (No Data_Exchange)

When SW3-4 is ON: PROFIBUS Status

RUN ERR EXPLANATION

EXTERNAL

DIAGNOS-

TICS

OFF OFF No Power ---

ON (Orange) OFF No Connection No

Flash (Red) Yes

Flash

(Green/Orange)

OFF Para / Cfg No

Flash (Red) Yes

ON (Green) OFF Data_Exchange No

Flash (Red) Yes

(*) Factory setting

R3-NP1

P. 3 / 4EM-8418 Rev.3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

INTERNAL POWER

INTERNAL

COMM. BUS

CONFIGURATION JACK JACK

BUS CONNECTOR

*Not provided with ‘No Power Supply’ type module.

RUN +

RUN –

RUN CONTACT OUTPUT

U (+)

V (–)

POWER INPUT

PROFIBUS

D-SUB CONNECTOR

WIRING INSTRUCTIONS

■ SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt. Applicable

wire size: 0.75 – 1.25 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

130 (5.12)

27.5 (1.08) 109 (4.29)6.1

(.24) POSITIONING

GUIDE

TERMINAL

COVER

6–M3

SCREW

6.2

(.24)

■ DIMENSIONS mm (inch)

■ CONNECTION DIAGRAM

R3-NP1

P. 4 / 4EM-8418 Rev.3

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive

remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this

warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original

sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

I/O DATA DESCRIPTIONS

■ ANALOG DATA (models: R3-SV4, YV4, DS4, YS4 and US4)

16-bit binary data.

Basically, 0 to 100% of the selected I/O range is converted into 0 to 10000 (binary). Negative percentage is represented in 2’s

complements.

■ TEMPERATURE DATA (models: R3-RS4, TS4 and US4)

16-bit binary data.

With °C temperature unit, raw data is multiplied by 10. For example, 25.5°C is converted into 255.

With °F temperature unit, the integer section of raw data is directly converted into the data. For example, 135.4°F is con-

verted into 135.

Minus temperature is converted into negative values, represented in 2’s complements.

■ DISCRETE DATA (models: R3-DA16 and DC16)

Input 1 (Output 1)

Input 2 (Output 2)

Input 3 (Output 3)

: :

Input 16 (Output 16)

0 : OFF (open)

1 : ON (close)

Other M-system Control Unit manuals

M-system

M-system M6NPS2 User manual

M-system

M-system R3-NMW1F User manual

M-system

M-system R3S-DC8 User manual

M-system

M-system R3-SV8B User manual

M-system

M-system R3-NM1 User manual

M-system

M-system R3-NC3 User manual

M-system

M-system R7M-DC4G User manual

M-system

M-system R7M-EC8A/UL User manual

M-system

M-system R7M-TS4 User manual

M-system

M-system R30MS4 User manual

M-system

M-system LONWORKS R3-NL2 User manual

M-system

M-system R3Y-PA16 User manual

M-system

M-system R7L-EC8A User manual

M-system

M-system R7F4DD-DC16A-H User manual

M-system

M-system R7ML-YS2 User manual

M-system

M-system R3-GC1 User manual

M-system

M-system R7M-EC8A User manual

M-system

M-system R3-PD16 User manual

M-system

M-system R3-CT4A User manual

M-system

M-system R8-DCM16ALH User manual

M-system

M-system R3-PA4 User manual

M-system

M-system R3Y-SS8N User manual

M-system

M-system R30CT4E User manual

M-system

M-system R7M-CT4E User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual