M-system F2DL User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5424 Rev.6 P. 1 / 2

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

• Install lightning surge protectors for those wires connect-

ed to remote locations.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 80mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

• Be sure that the ventilation slits are not covered with ca-

bles, etc.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 30 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Body

Zero Adj.

Span Adj.

Connection

Diagram

Specifications

Euro Type

Connector Terminal Block

INSTALLATION

Set the unit so that its DIN rail adaptor is at the bottom.

Hang the upper hook at the rear side of the unit on the DIN

rail and push in the lower. When removing the unit, push

down the DIN rail adaptor utilizing a minus screwdriver

and pull.

DIN Rail

35 mm wide

Spring Loaded

DIN Rail Adaptor

CURRENT LOOP SUPPLY

(with square root extractor; non-isolated) MODEL F2DL

F2DL

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-5424 Rev.6 P. 2 / 2

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

1234

5678

107 (4.21) [1.5 (.06)]

DIN RAIL

35mm wide

22.5 (.89)

75 (2.95)

• When mounting, no extra space is needed between units.

■CONNECTION DIAGRAM

–

OUTPUT

POWER

–

MONITOR

(4 – 20mA DC)

2-WIRE

TRANSMITTER

WIRING INSTRUCTIONS

■EURO TYPE CONNECTOR TERMINAL

Applicable wire size: 0.2 to 2.5 mm2

Stripped length: 7 mm

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

7 – 8 with a multimeter.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 30 minutes.

1) ZERO: Apply 1% input and adjust output to 10%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 1% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 30 minutes. Apply 0%, 4%,

16%, 36%, 64% and 100% input signal. Check that the out-

put signal for the respective input signal shows 0%, 20%,

40%, 60%, 80% and 100% within accuracy described in the

data sheet. When the output is out of tolerance, recalibrate

the unit according to the “ADJUSTMENT PROCEDURE”

explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Other M-system Control Unit manuals

M-system

M-system R7M-RS4 User manual

M-system

M-system R5T-DA4 User manual

M-system

M-system R30YV4 User manual

M-system

M-system R7M-EA8 User manual

M-system

M-system R7HL-DC16B User manual

M-system

M-system R30CT4E User manual

M-system

M-system R3-RR8 User manual

M-system

M-system M6NPS1 User manual

M-system

M-system R7D-EA16 User manual

M-system

M-system R7C-DC16B User manual

M-system

M-system R7ML-EC16A User manual

M-system

M-system R7M-EC8A User manual

M-system

M-system R3-PA2 User manual

M-system

M-system R3S-DC8 User manual

M-system

M-system R7L-SV4-R User manual

M-system

M-system R8-NECT1 User manual

M-system

M-system EtherCAT R7I4DECT-1-PA8A User manual

M-system

M-system R30BS User manual

M-system

M-system R3-AS4 User manual

M-system

M-system R7HL-YS2 User manual

M-system

M-system R3-PT4 User manual

M-system

M-system R7ML-DC16D User manual

M-system

M-system R3S-RR8 User manual

M-system

M-system R6D-TS2 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual