Luxli TIMPANI2 User manual
QUICKSTART GUIDE
2
Precautions
• Keep this product away from water and ammable gases or liquids.
• Use only the correct, recommended voltage.
• Do not attempt to disassemble or repair this product.
• Clean this product with only a soft, dry cloth.
• To avoid damage to this product, be careful not to overtighten or improperly thread any of the
threaded ttings.
• All images are for illustrative purposes only.
Firmware Upgrade
Firmware updates are available through the Composer app. Refer to the Timpani’s full user manual
available at www.luxlilight.com for information and instructions.
Troubleshooting
• If you encounter any problems, rst try turning the device off and then on.
• If the problem persists, remove the batteries or power supply for 15 seconds,and then restart.
• Go to luxlilight.com to make sure you have the most recent rmware update.If a new rmware
version is available, follow the instructions on how to download it to your light.
• Contact Luxli support at 212-594-2353 or at www.luxlilight.com.
3
Front:
1. Diffuser
2. Diffuser thumbscrews
3. Tilt lock handle
4. Tilt control screw
Overview
5. Center mounting screw
6. Outer mounting screw
7. Locking handle
8. 5/8 in. receiver
3
2
4
21
86 75
4
Back:
1. Removable handle
2. 4-pin power input
3. Manufacturer’s service port
4. 5-pin DMX input
5. 5-pin DMX output
6. Bluetooth antenna
7. User interface (see Interface Overview p. 8)
DC 12.5–30 V SERVICE DMX IN DMX OUT
MODE
TIMPANI2
1
65432 7
5
Also included:
• 4-pin XLR cable
• AC cable (3-Prong US - C5 Connector)
• Photometric calibration results data sheet
Power supply:
1. 4-pin power output
2. V-mount battery plate
3. Battery release button
4. AC power input
1
2
3
4
6
Setting Up the Timpani2
Attaching the Tilt Lock Handle
The tilt lock handle can be attached to either side of the Timpani.To attach the handle,follow these steps:
1.
Place the Timpaniand yoke facedown on a
at surface.
2.
Use the included hex key to remove one of the
tilt control screws,and replace it with the tilt lock
handle.Screw in the handle so the threads are
engaged, but don’t tighten it.
3.
Use the hex key to tighten the control screw on
the other side of the yoke.Tighten it enough
until there is some resistance while tilting the
Timpaniin the yoke.
4.
Tighten the handle until the yoke is locked and
secure.
Note: If the yoke seems too loose when the tilt lock
handle is disengaged, use the hex key to slightly
tighten the control screw opposite the handle.
7
Powering the Timpani2
Battery Power
1. Connect the 4-pin XLR cable to the power supply and the Timpani.
2. Slide a V-mount battery into the power supply’s battery plate until it locks into place.
To remove the battery, press the battery release,and slide it off the plate.
AC Power
1. Connect the 4-pin XLR cable to the power supply and the Timpani.
2. Connect the AC cable to the power supply and a power outlet.
Important! If the power supply is connected to both a 26 V battery and an AC power source, the power
supply will draw from the 26 V battery instead of the AC power.
To preserve battery life, connect a 26 V battery to the power supply only when you intend to use it.
8
Interface Overview
1 . Intensity Dial
In all operation modes, the Intensity dial adjusts to the intensity from 100% to 0% in 1% increments.
In all operation modes, press the Intensity dial to toggle between the set intensity and 0%.
2 . Power Button
Press to power on or off.
3 . Mode Selector
Cycles through the ve operating modes: CCT, HSL, Filter, HFR, and Effects.
4 . Function Buttons
The function buttons implement the action or access the menu indicated on the LCD screen next to
the button.
5 . Adjustment Dial
In all operation modes, the Adjustment dial changes the value of the highlighted function.
MODE
1 2 3 4 5
9
User Interface
1 . Intensity
2 . Bluetooth Indicator
3 . Functions
Displays the active actions for each operating
mode or screen.The button next to the function
implements the function.
4 . Menu Button
Switches to the main menu (see Main Menu
p. 13).
5 . Power Display
• Batteries with SMBUS data
communication:
The Timpanidisplays an estimated time
remaining at the top of the screen.
• Batteries without SMBUS data
communication or AC power:
The Timpanidisplays the actual voltage
of the power source.This allows you to
gauge the remaining battery power.
32%
3900K
+/- GREEN
0%
CCT
32% 24.2V
32% 3h 31m
32% 24.2V
1 2 3
4
5
10
1 . Intensity
2 . CCT
• Select any color temperature from 2800 to
10,000 K in 50 K increments.
• Press the Adjustment dial to toggle
between 3200 and 5600 K.
3 . Tint (+/− Green) Screen
• Sets the green/magenta saturation level
in 1% increments from +100% to -100%.
1 . Crosshair
• Shows current position on the color graph
2 . Hue
• Adjusts in 1 degree increments.
3 . Saturation
• Adjusts in 2% increments.
4 . White Point
• Adjusts Base White Point from 3000 to
10,000 K in 50 K increments.
CCT Mode
HSL Mode
32%
3900K
+/- GREEN
0%
CCT
32% 24.2V
100
SAT
HUE
169
WHITE P.
6500K
32% 24.2V
1
1
4
32
2 3
Other manuals for TIMPANI2
1
This manual suits for next models
1
Table of contents
Other Luxli Lighting Equipment manuals
Luxli
Luxli TIMPANI2 User manual
Luxli
Luxli Timpan-1x1 User manual
Luxli
Luxli ORCHESTRA Series User manual
Luxli
Luxli ORC-TAIKO-2x1 User manual
Luxli
Luxli CELLO 2 User manual
Luxli
Luxli ORC-CELLO-10-DK User manual
Luxli
Luxli VIOLA 2 User manual
Luxli
Luxli ORC-CELLO-M2 User manual
Luxli
Luxli SFT-50R User manual
Luxli
Luxli Taiko User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
