Luxier SS-C01-TB User manual

1SS-C01 Rev. C 072021

Luxier

SS-C01-TB (Brushed Nickel)

SS-C01-TC (Chrome)

SS-C01-TM (Matte Black)

SS-C01-TO (Oil Rubbed Bronze)

Specications:

Shower head ow rate: maximum 1.8 gpm at 80 psi

Plumbing connection: standard 1/2” pipe tting

Rainfall Shower System

IMPORTANT!

• Read and understand this instructions completely before installation. Failure to follow these

instructions could prevent the valve from working properly. Consult a professional installer if needed.

• This installation guide is subject to change without notice, please contact us to request the most

updated version of this installation guide.

• This is a general installation guideline, actual installation may vary. It is recommended the

installation is performed by a trained and experienced installer.

• Please follow all local building and plumbing codes.

• Proper pressure must be maintained for the pressure balance valve to work properly. Make sure

water pressure is about the same on both hot and cold water side.

• Product drawings in this installation guide is for illustration purpose only. Actual product may vary

depends on model.

• Always take extra precautions and wear appropriate safety equipment when installing this product.

• Unpack and inspect the parts from the package for shipping damage and make sure all parts are

included in the package. Keep the product in its package until you are ready to install.

• Make sure the installation site is clean and free of dust and debris.

2SS-C01 Rev. C 072021

Luxier

Thank you for purchasing Luxier products. Please read the information below and keep this

installation guide for future reference. If you require assistance, please contact our customer service

department at 1-877-711-8828, Monday - Friday 9AM - 5PM Paci c Time or by email at

[email protected].

Limited Lifetime Warranty (For USA Only)

The manufacturer warrants this product to be leak and drip free during daily normal household use

for as long as it is owned by the original purchaser of this product. Please keep a copy of the original

invoice as proof of purchase.

Should a malfunction occur within the warranty period, Luxier USA will, as its option, (1) repair or

replace the defective part(s) or product at no charge; (2) issue a refund of the purchase price paid

for the product (Valid within 30 days from the date of purchase); or (3) issue a credit to be applied

against the purchase of a new Luxier product. Shipping/delivery charges may apply and are in Luxier

USA’s sole discretion.

This limited warranty shall not apply to goods which have been subject to accident, negligence,

improper installation, product abuse, product misuse, or use of cleaners containing abrasives, alcohol

or other organic solvents, whether performed by a contractor, service company, or yourself, are

excluded from this warranty.

Our responsibility under this warranty is limited to only to replacement parts and no other costs.

Luxier USA will not be responsible for labor charges and/or damage incurred by installation, repair or

replacement, nor for any indirect incidental or consequential damages, losses, injury or costs of any

nature relating to this faucet. Except as provided by law, this warranty is in lieu of and excludes all

other warranties, conditions, and guarantees, whether expressed or implied, statutory or otherwise,

including without restriction those merchantability of  tness for use.

This limited warranty is non-transferable. This limited warranty only applies to products purchased

and installed in the United States. This limited warranty covers the original consumer purchase only

and does not include business, commercial or industrial use of this product. To obtain service under

the Limited Warranty, please contact Luxier USA at [email protected]. The Luxier USA Customer

Care Department will determine whether to repair or replace your product, issue a refund, or issue a

credit.

Recommended Tools and Materials

1. Safety Glasses 6. Adjustable Wrench

2. Teon (PTFE) Tape 7. Screwdriver Sets

3. Plumber’s Putty and Caulking 8. Torch

4. Tube Cutter 9. Hacksaw

5. Marker / Pencil

3SS-C01 Rev. C 072021

Luxier

01 Shower Head

02 Shower Arm

03 Flange

04 Valve Body

05 Rubber Gasket

06 Cap

07 Hot Water Stop Valve Assembly

08 Cold Water Stop Valve Assembly

09 Pressure Balance Cartridge

10 Cartridge Nut

11 Stem Extension

12 Threaded Nipple

13 Protective Cover*

14 Temporary Screws*

15 Protective Sleeve*

16 Escutcheon

17 O-Ring

18 Handle

19 Tub spout

20 Plunger

21 Spring

21 Screw

23 Stop Valve Nut

*Is NOT used in nal installation

Parts Diagram & Dimensions

13 1/4”

4 1/2”

2 1/2”

7 5/16”

4 15/16”

5 1/2”

2 9/16”

3”

7 7/8”

* Drawings not to Scale. All Measurements are Approximate *

1/2” NPT

20 21

13*

14* 15*

4SS-C01 Rev. C 072021

Luxier

Installation

2. Connect the valve to the plumbing system with proper

ttings. Perform a dry t before soldering pipes to the

valve. (Fig. C)

WARNING: Exposure to high temperature will damage

the cartridge (9) and stop valves (7, 8). Remove these

parts before soldering.

3. After the pipes are soldered, install the stop valves (7,

8), cartridge (9), stem (11), and threaded nipple (12) back

onto the valve body. NOTE: Make sure the cartridge is

installed in the upright position. The “UP” marking on the

cartridge should point upward. (Fig. C1)

4. Pressure test and ush the valve. NOTE: Pressure must

be approximately equal on both hot and cold side for the

valve to function properly. (Fig. D)

• Install a 1/2” iron pipe plug (not included) on the

shower and tub outlet.

• Turn the valve to ON position and check all connections

for leaks for about a minute.

• Turn the valve to OFF position after pressure test.

Make sure the pipes are free of debris or sediments

and remove both 1/2” plugs.

5. Install the tub spout pipe after pressure test. The 1/2”

male threaded nipple should extend about 4 3/16” from

the nished wall as shown in Fig. D1. NOTE: Apply some

PTFE tape on the male end of the threaded nipple before

connecting it to the pipe in the wall.

Finished Wall

Protective Cover

Recommended

2 11/16” - 3 7/16”

WARNING: Remove all parts before soldering

Stop Valve (7, 8)

Cartridge (9)

30”

48”

min. 8”

* Drawing not to Scale

(Shower)

DOWN

(TUB)

HOT

COLD

Pressue Balance Cartridge

5.06”

1. Position valve body in the wall. It is recommended the valve to be about 48” above the nished oor

and shower outlet to be about 30” above the valve (Fig. A1) The nished wall should be set between the

markers on the temporary protective cover. The recommended depth is 2 11/16” to 3 7/16”. (Fig. A) Make

sure the UP outlet is pointed upward. (Fig. B)

NOTE: Valve access hole on the wall should be 6” in diameter and outlet hole for shower arm is about

1 1/4” in diameter.

Mounting Hole

Cold WaterHot Water

5SS-C01 Rev. C 072021

Luxier

Installation (Cont.)

7. Remove the handle and the escutcheon plate and set

them aside. Remove the threaded nipple (12) and the stem

extension (11) from the valve body. Use a hacksaw to trim

the threaded nipple (12) and stem extension (11) based

on the measurement taken in step 5 gure E1 as shown in

gure F. (NOTE: Do not trim the stem extension (11)

and threaded nipple (12) directly on the cartridge

because it will damage the cartridge. Trim the pieces

separately, do not trim both parts at the same time. It

is best to cut o only small amount of the brass stem

and test t the handle.)

8. Re-install the threaded nipple (12) and stem extension

(11) assembly to the valve body. Carefully slide the

escutcheon plate onto the valve and attach the handle

assembly shown in gure G.

9. Slide the ange (3) onto the shower arm (2) and apply

PTFE tape to both ends of the shower arm. Attach the

shower arm to the plumbing and slide the ange on the

wall. Attach the shower head (1) as shown in Fig. H.

(NOTE: Do not over tighten the connections.)

10. Apply some PTFE tape to the thread on the tub

spout pipe and install the spout as shown in Fig. I. The

installation is now complete.

11. Turn on the water and check for leaks at all

connections. Pull the diverter knob on the spout to divert

the water to the shower head. (Fig. J)

12. Turn on the water and check for leaks at all

connections. The installation is now complete.

11 12

5. Remove and discard the protective sleeve (15) and cover (13) from the valve. Slide the escutcheon

onto the valve as shown in Fig. E. Place the handle assembly on the stem extension and turn the handle

clockwise to install the handle. If there is a gap when the handle is attached to the valve measure and

write down the distance of the gap between the handle and the escutcheon plate as shown in Fig. E1.

6SS-C01 Rev. C 072021

Luxier

Operation

1. Turn the handle counter-clockwise from the OFF position

to the BLUE dot (cold water) to start the water ow. Continue

turning the handle to the RED dot (hot water) for achieve

the maximum hot water temperature. (CAUTION: Scalding

may occur if the control is set to maximum temperature.) It is

strongly recommended to set the handle halfway between the

BLUE and RED dots as the starting point. Gradually turn the

knob to set the desired water temperature.

2. Pull the diverter knob on the spout to divert water to the

shower head.

3. To turn o the water, return the handle to the OFF position.

COLD (blue)

HOT (red)

Troubleshooting

Problem

Shower valve produces loud humming / vibrating noise when water is running

Possible Cause

1. Debris or sediment inside the cartridge, valve body, or plumbing system

2. One or both the plungers inside the stop valves may have shifted (mis-aligned) during transport

Solution: Clean Out Debris and Reset the Plungers

1. Shut o water to the valve

2. Remove Handle and Escutcheon

3. Remove the Threaded Nipple, Stem Extension, and Cartridge Nut and pull out the Cartridge

4. Clean and make sure the Cartridge is free of debris and sediments

5. Remove both Stop valves with an adjustable wrench. (CAUTION: Be careful removing the Plungers

and the tiny Springs when removing the Stop Valves. See Fig. 1)

6. Clean out any remaining debris or sediments inside the valve body

7. Re-install the Stop Valves Assemblies (including the Plungers and Springs) and use a large at head

screwdriver, turn both screws on the stop valves clockwise to close the stop valves completely. Once

the valves are closed, turn the screws counterclockwise to open both valves again. Make sure to fully

open the valves for maximum water ow. This step will reset the Stop Valves. (See Fig. 2)

8. Re-install the Cartridge and assemble the parts

9. Turn of water to the valve and test the unit to complete the service

Plunger

Spring

7SS-C01 Rev. C 072021

Luxier

Maintenance Guide

Please follow the cleaning material manufacturer’s instructions. Damage caused by improper

treatment will not be covered by product warranty. In addition, pay attention to the following points:

• Regular cleaning can prevent mineral build up on faucet spout.

• Carefully read the cleaner product label to ensure the cleaner is safe for use on the material.

• Test the cleaner on a small area before using on the entire surface.

• Use a mild detergent such as liquid dishwashing soap and warm water for cleaning.

• Do not use abrasive / harsh chemical when cleaning the  xture as they will damage and dull the

 nish.

• When using spray cleaners, spray  rst onto a soft cloth or sponge. Never spray directly onto the

faucet as droplets can enter openings and gaps and cause damage.

• After cleaning, rinse thoroughly with clean water to remove any cleaner residue.

Service the Valve and Pressure Balance Cartridge

NOTE: To maintain the performance of the shower valve. It is recommended to clean the pressure

balance cartridge at least once a year. More frequent cleaning is needed if the water has high mineral

content.

1. Remove shower trims (#16, #17, #18)

2. Turn o water supply at the stop valves (#7 and #8) by using a large at head screwdriver and turn

the valve clockwise to shut o the water.

3. Remove the threaded nipple (#12), stem extension (#11), and cartridge nut (#10) and pull out the

cartridge (#9) with a pair of pliers.

4. Use commercially available hard water scale remover to clean the valve. Dilute the solution as

instructed on the cleaner. Soak the valve for about 5 minutes in the solution and clean it with a soft

brush. Thoroughly wash o any cleaning solution and debris on the cartridge.

5. After cleaning, follow the above steps in reverse order to assemble the valve.

This manual suits for next models

Table of contents

Popular Bathroom Fixture manuals by other brands

DURAVIT

DURAVIT C.1 C15240 0090 Instructions for mounting and use

Heatstore

Heatstore HSTRL500WTN Installation and operating instructions

Sunshower

Sunshower PURE SOLO manual

Delabie

Delabie Delabie Sporting 714700 manual

Kohler

Kohler K-13056 Homeowner's guide

ESS

ESS Container TCL-11 installation manual

Mustee

Mustee 22C installation instructions

VITRA

VITRA V-Flow manual

baliv

baliv DUK-80.30 T manual

Malmet

Malmet B105BT Operation, maintenance and installation manual

bathstore

bathstore Transition H1690MM Installation, Care & Adjustment Instructions

BELLOSTA

BELLOSTA Edward 0800/M Installation instruction

baliv

baliv DU-5160 manual

Franke

Franke PRTR0006 Installation and operating instructions

Gessi

Gessi RILIEVO 59011 manual

noken

noken VITAE 100188525-N299998810 manual

Allen + Roth

Allen + Roth 1142VA-30-201 manual

Britex

Britex HBDA installation guide