LUCCI Air AIRFUSION BALI Installation guide

v1.0-AU (09/2020)

LUCCI

AIRFUSION BALI

DC CEILING FAN

⚫INSTALLATION

⚫OPERATION

⚫MAINTENANCE

⚫WARRANTY INFORMATION

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE

INSTALLATION AND FAN OPERATION.

AIRFUSION BALI Installation Instructions

1 | P a g e

THANK YOU FOR PURCHASING

Thank you for purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power

which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and

silent operation.

Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to

65% more energy than ceiling fans with traditional AC motors.

Silent operation – This DC fan motor is programmed with a stabilised current which efficiently reduces motor

noise.

Low operating temperature – The DC power is managed effectively which brings down the motor operating

temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the

longevity of the motor.

6 speed remote control - Regular AC ceiling fans usually come with only 3 speeds, this DC fan comes

complete with a 6 speed remote, which gives a greater choice of comfort levels.

SAFETY PRECAUTIONS

1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

2. Children should be supervised to ensure that they do not play with the appliance.

3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring

rules.

WARNING:

FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION

MUST BE INCORPORATED INTO THE FIXED WIRING IN

ACCORDANCE WITH THE WIRING RULES.

As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum

electrical safety of this standard.

Please note warranty will be void if installation is without a means for an

all-pole disconnection incorporated in the fixed wiring in accordance with

the wiring rules.

AIRFUSION BALI Installation Instructions

2 | P a g e

Example: If a fan is connected to a circuit that can be isolated via an all-

pole safety switch at the switchboard, then this is considered to be an

all-pole disconnection to the ceiling fan electrical circuit, meeting the

requirements of clause 7.12.2 of AS/NZS 60335.1.

A single-pole switch on the active of the receiver input of remote

control must also be included in the wiring, and located the same

room as the ceiling fan.

4. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.

Contact your local government for information regarding the collection systems available. If electrical

appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water

and get into the food chain, damaging your health and well-being.

5. The structure to which the fan is to be mounted must be capable of supporting a weight of 45 kg.

6. The fan should be mounted so that the blades are at least 2.1m above the floor.

7. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2

walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in

a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty.

Mounting the fan in a situation where it is subject to water or moisture is dangerous and may increase the

risk of damage, injury or electrical shock.

8. Must be assembled and installed by a licensed electrician.

9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling

fan and contact the manufacturer, its service agent or suitably qualified persons.

10. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,

its service agent or suitably qualified persons.

11. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a

sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension

system shall be performed by the manufacturer, its service agent or suitably qualified persons.

AIRFUSION BALI Installation Instructions

3 | P a g e

PARTS LIST

•Unpack your ceiling fan carefully. Remove all parts and hardware.

•Lay out all the components on a smooth surface and make sure there are no components missing before

assembling. If parts are missing, return the complete product to the place of purchase for inspection or

replacement.

•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product

which appears damaged in any way. Return the complete product to the place of purchase for inspection,

repair or replacement.

•Examine all parts, you should have the following:

Fig. 1

AIRFUSION BALI Installation Instructions

4 | P a g e

INSTALLING THE FAN

TOOLS REQUIRED:

- Phillips / flat head screwdriver

- Pair of pliers

- Adjustable spanner

- Step ladder

- Wire cutter

- Wiring, supply cable as required by local provincial and national wiring codes and regulations

INSTALLING THE MOUNTING BRACKET

•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the

blade to the nearest objects or walls.

•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 45

kg, with two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig.

NOTE: The bracket screws provided are for use with wooden structures only. For structures other

than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the

mounting surface and the surrounding environment.

Mounting bracket x1

Fan Blades x5

Canopy Cover x1

Fan blade bracket x5

Down rod and ball joint x1

Blade mounting screw x8 (1 spare)

Down rod coupling housing

cover x 1

Blade and bracket assembly screw

and washer x 20 sets (1 Spare set)

Fan motor assembly x1

Mounting bracket Screw x2

Light kit x1 (18W GX53 lamp is

pre-installed in the light kit)

Blade balancing kit x1 set

Remote receiver and Remote controller, battery, holder x 1 set

Fig. 2

45 KG

AIRFUSION BALI Installation Instructions

5 | P a g e

ANGLED CEILING INSTALLATION

This fan hanging system supports a maximum 10 degree angled ceiling installation. (Fig. 3)

INSTALLING THE DOWN ROD (Fig. 4)

Fig. 3

10°

1. Remove the ball joint (2) and dowel pin (3) by loosening the set screws (4) from the down rod (6). Remove

the hitch pin (9) by removing the lock clip (10). NOTE: Do not discard keep these parts, they are required

to reassemble later. (Fig. 4.1)

2. Loosen the set screws (11) on the down rod coupling housing (8). (Fig. 4.2)

3. Carefully feed the fan wires (1) up through the down rod (6). (fig. 4.3)

4. Assemble the down rod (6) into the down rod coupling housing (8), by inserting and line up the down rod

coupling housing holes with the down rod holes and insert the hitch pin (9) and secure with the lock clip (10).

(Fig. 4.3)

5. Secure the down rod (6) by tightening the set screws (11). (Fig. 4.4)

Fig. 4.1

Fig. 4.2

Fig. 4.3

Fig. 4.4

AIRFUSION BALI Installation Instructions

6 | P a g e

INSTALLATION OF BLADE (Fig. 5)

1. Assemble the fan blades to the fan blade bracket by tightening the 4 blade screws and washers. Take

note the correct side of the blades with the marking “THIS SIDE UP” is on the screw head side. (Fig. 5.1).

2. Install the fan blade assembly to the fan assembly by the 2 screws and spring washer set. (Fig. 5.2)

3. Repeat the same process for the other blades.

Ensure all screws are tightened evenly to reduce the chance of warping or unbalancing. Take care not to over

tighten the screws, as this can damage the blades.

6. Insert the decorative cover (7) onto the down rod (6) to cover the down rod coupling housing (8).(Fig. 4.5)

7. Insert the canopy (5) over the down rod (6) and install the ball joint (2) and dowel pin (3) back onto the

down rod (6) and secure by tightening the set screws (4). (Fig. 4.5 and Fig. 4.6)

Fig. 4.5

Fig. 4.6

THIS SIDE UP

Fig. 5.1

AIRFUSION BALI Installation Instructions

7 | P a g e

INSTALLATION OF LIGHT KIT (Fig. 6)

NOTE: The light kit must be installed by a licensed electrician.

•Connect the wires of light kit to the fan assembly via the quick connector.

•Install the light kit on the fan assembly then secure it by turning clockwise.

Fig. 6

Fig. 5.2

AIRFUSION BALI Installation Instructions

8 | P a g e

INSTALLATION OF LAMP (Fig. 7)

•NOTE: The GX53 lamp is pre-installed in the light kit. Follow the below if it is required to replace the lamp.

•Remove the lamp shade from the light kit.

•Replace the GX53 lamp with a new one. Do not exceed the maximum power rating.

•Install the lamp shade back onto the light kit.

HANGING THE FAN

Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on

the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig. 8)

Fig. 8

Fig. 7

AIRFUSION BALI Installation Instructions

9 | P a g e

ELECTRICAL WIRING DIAGRAM THE FAN

PREPARE AND COMPLETE THE ELECTRICAL WIRING --- WIRING DIAGRAM (FIG. 9)

WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A LICENSED

ELECTRICIAN.

NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED WIRING.

NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN

ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN PROGRAMMING

THE REMOTE AND RECEIVER TO PAIR TOGETHER.

Ensure the motor earth wire is connected to the single earthing terminal block “1” in the diagram (Fig. 9)

From mains supply to mounting bracket terminal block: (Fig. 9)

1. Connect the live supply wire to the “L” terminal of the terminal block on the mounting bracket.

2. Connect the neutral supply wire to “N” terminal of the terminal block on the mounting bracket.

3. Connect earth wire to the earth terminal of the terminal block on the mounting bracket.

From mounting bracket to receiver and motor : (Fig. 9)

4. Connect the supply wiring from the mounting bracket to the input of the DC motor driver/receiver.

5. Connect the output wires of DC motor driver/receiver to the input wires of the fan motor and the light kit.

6. Connect the earth wire from the Fan motor to the earth terminal block from the mounting bracket.

DC motor and Light Kit

input wiring connector.

Receiver output wires to

DC motor and Light kit

Fan motor

earth wire

Earth wire

terminal from

mounting bracket

Fig. 9

Table of contents

Other LUCCI Air Fan manuals

LUCCI Air

LUCCI Air BREEZE 8 Installation guide

LUCCI Air

LUCCI Air GRENADA Series User manual

LUCCI Air

LUCCI Air AIRFUSION MOTO LD-MOTO-52 Installation guide

LUCCI Air

LUCCI Air AIRFUSION CLIMATE III Installation guide

LUCCI Air

LUCCI Air AIRLIE HUGGER Installation guide

LUCCI Air

LUCCI Air AIRFUSION AIRMOVER Installation guide

LUCCI Air

LUCCI Air AIRFUSION CAROLINA Owner's manual

LUCCI Air

LUCCI Air POLIS 216162 Owner's manual

LUCCI Air

LUCCI Air AIRFUSION OSTUNI LD-MF-56 User manual

LUCCI Air

LUCCI Air Airfusion Radar User manual

LUCCI Air

LUCCI Air METT User manual

LUCCI Air

LUCCI Air ATLANTA User manual

LUCCI Air

LUCCI Air AIRFUSION SLIPSTREAM User manual

LUCCI Air

LUCCI Air SUMMIT Series User manual

LUCCI Air

LUCCI Air OSPREY 216170 Owner's manual

LUCCI Air

LUCCI Air NEWHAVEN 216150 Owner's manual

LUCCI Air

LUCCI Air FIJIAN II Series User manual

LUCCI Air

LUCCI Air AIRFUSION BREEZE Installation guide

LUCCI Air

LUCCI Air AIRFUSION MARINER User manual

LUCCI Air

LUCCI Air Airfusion Akmani Series Guide

LUCCI Air

LUCCI Air AIRFUSION FRASER Series User manual

LUCCI Air

LUCCI Air AIRFUSION AKMANI Installation guide

LUCCI Air

LUCCI Air AIRFUSION UNIONE-56 ORB User manual

LUCCI Air

LUCCI Air Nordic User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual