Lock Control SL-166A User manual
Page 1
27
90
3.5
39
32
160
Use for 90 ~180 open hollow metal or solid wooden doors.
Built-in microcontroller.Automatic current output control
according to the door leaf position. The currentis being
lowered to 210mA after 6 seconds of door leaf positioning
in order to cut down power consumption and lower the
temperature of the lock body.
Special wearable design. Mechanic life of more than
200,000 times.
Adjustable wiring methods according to the environment.
Adjustable lock time( 0 sec. & 3 sec. ).
1 set of push button control contact is available.
Lock indicator is available for lock status.
Features
SL-166A(B) Dead Bolt Lock Installation Manual
Unit: mm
Accessories
Lock body X 1 5-PIN Connector
M5X25mm X 2Screws
M4X15mm X 4Screws
M5X8mm X 4Screws
M4X8mm X 8Screws
X2 Shims(small)
For strike plate
X2 Shims(large)
For lock body
Bolt
14mm (Throw) X 12.7mm (Diameter)
Safety Measures
(1)Fail-safe electric lock
(2)Built-in photo couplers door open
push button input contact.
Door will lock again automatically when
door is not open within 6 seconds.
Specifications
Door position reed contact (0.25A@30VDC)
Lock status sensor
Maximum 41 ( )Room temperature 30
Operation temperature
DC 12V 10%
Power supply
Temperature 0-70 ,Humidity85%Rh max
Operation environment
0,3 sec.( Adjustable)
Delay Time
Mechanic life More than 200,000 times
Operation current Standby:210mA 10%;
Operation:570mA 10%
Current and Temperature Chart
Current
(MA)
Time (sec.)
Time (sec.)
Temperature
Start
Stand-by
Door Close
Door Lock
Delay Timer
If delay time of 3 seconds.
Door closed whenpower is on.
5
60
50
40
30
20
Adjusting before installation
Unscrew the top cover, adjust delay time.
Adjusting automatic locktime:
(Reset after adjusting)
0SEC. 3SEC.
1
(Default)
Wiring direction according to the
environment.
3
OR
2
The wires through the
rubber hole
Connections
Attention: There are only 2 screws on the back of the panel.
Push button contact as dry contact. NO voltage input to prevent
damage to the unit.
Current input
Screws
Strike plate X1
Push button input contact
COM.
N.O.
N.C.
Red:
Brown:
Green:
Blue:
Purple:
Yellow:
Door position detection reed is only able to sustain load of
0.25A@30VDC. An external relay is suggested if higher current
to control.
SL-166A has NC and COM contacts
( Environment: Room temperature 30 ,
Humidity 60% Rh,DC12V )
Lock Control - Kouterbaan 63 - 1840 Malderen - Belgium - Tel. +32 52 57 43 02 - [email protected] - www.lockcontrol.be
Page 2
-
+
AP-10
DC 12V
1A
PUSH BUTTON
RED
READER
BROWN
GREEN
Wiring Diagram
Maximum distance as 6mm.
It is unable to lock if the
spacing is exceeding 6mm.
Attention
Installation
N.O.
COM
N.C.
It is suggested to use an external relay (COM & NC)
if it is exceeding the load of output contact.
-
+
COM
NCNO
R
Br P
Blu
Example
Door position detection output
When door is closed, bolt strikes
after delay time count, detection
output is COM and N.O. connected.
Load External power
Diode
Page 2
The unlock operation temperature of the lock is normally within 41 .
It is considered normal if the temperature is within 41 .
1. Please check power supply (DC-12V)
(600mA current is needed to activate).
.
Please check the power supply.
Continuous locking ( bolt strikes and retracts) when the door is closed.
1. The spacing gap is too wide (>6mm) between the unit and the magnetic panel which is unable to detect
the correct position.
2. Insufficient of current output or malfunction of the power if this event occurred in a sudden when the lock
has been installed for ages.
No operation after installation.
FAQ
The lock is hot.
N.O.
COM
N.C.
(Not available for SL-166A)
When door is not closed, bolt does
not strike, detection output is COM
and N.C. connected.
161
33
28
91
41
141
28
161
Lock Control - Kouterbaan 63 - 1840 Malderen - Belgium - Tel. +32 52 57 43 02 - [email protected] - www.lockcontrol.be
2. Please check if there is short circuit of the push button contact.
3. Please make sure to place strike plate on the lock and aim the bolt hole with the bolt.
Please make sure the position of the magnet is right before testing the electric lock.
This manual suits for next models
1
Other Lock Control Door Lock manuals
