Linksys NSLU2 - Network Storage Link NAS Server User manual
Model No.
Quick Installation Guide
A Division of Cisco Systems, Inc.
®
WIRED
NSLU2 (EU/UK/LA)
Network Storage Link
Package Contents
• One NSLU2 - Network Storage Link
for USB 2,0 Disk Drives
• One Power Adapter
• One 6 ft. Ethernet Cable
• One Setup Wizard CD with User Guide
(English Only) in PDF format
• One Quick Installation
•OneDeviceStand
for USB 2,0 Disk Drives
2
1Connect the Network Storage Link
APlug the included Ethernet
cable into the Network
Storage Link’s Ethernet port.
Then, connect the other end
to your hub or switch.
BConnect the USB storage
devices.
If you are using a USB flash
memory device (USB Key),
insert it in the Disk 2 port.
This Quick Installation will explain how to physically connect the Network
Storage Link to the network and how to set up the Network Storage Link for
basic operation.
Before you install the Network Storage Link, make sure these requirements
have been met:
• TCP/IP protocol is installed on your PCs
• a port is available on a hub or switch (to connect to the network)
• you have a USB flash drive and/or a USB hard disk drive (to store data)
If these requirements have been met, then proceed to Step 1.
A
B1
NOTE: The flash drive must be inserted
into the Disk 2 port. It will not work if it
is inserted into the Disk 1 port.
IMPORTANT: The Network Storage Link
is not hot-swappable. Make sure that
the Network Storage Link is powered off
before you connect or disconnect any
USB flash or hard disk drive.
3
If you are connecting a USB
hard disk drive, you can
connect it to either port;
however, Linksys recommends
that you connect the first hard
disk drive to the Disk 1 port.
APlug the power cord into the
Network Storage Link's power
port. Then connect the other
end to an electrical outlet.
BTo power on the Network
Storage Link, press the power
button once. (It is located near
the bottom of the front panel.)
CThe Network Storage Link will
run a brief self-test (2 or 3
seconds) before actually
booting up. During the self-test,
all of the Network Storage Link's
LEDs will be lit or flashing.
When the self-test is complete,
the Ready/Status LED will flash
continuously, and the Ethernet
LED will flash occasionally as
the Network Storage Link is
booting up. This should take
approximately 1-3 minutes.
When boot-up is complete, the
Ready/Status LED and the
Ethernet LED will be
continuously lit.
C
B2
D
4
• If a flash memory or USB disk
is connected to the Disk 2
port, the Disk 2 LED should
be lit.
• If a USB hard disk drive is
connected to the Disk 1 port,
the Disk 1 LED should be lit.
• If the Network Storage Link
repeatedly beeps, there is a
hardware problem. Refer to
the Troubleshooting section
of the User Guide on the CD-
ROM for possible solutions.
Proceed to Step 2.
NOTE: For details about
removing or changing USB
storage devices, refer to the User
Guide on the CD-ROM.
5
A
AInsert the Setup Wizard CD-
ROM into your PC’s CD-ROM
drive.
The Setup Wizard should
run automatically, and the
Main Menu
screen should
appear. If it does not, click
Start
and then
Run
. In the field
provided, enter
D:\SetupUtility.exe
(if “D” is the
letter of your CD-ROM drive).
BClick the Setup button.
CThe Setup Wizard will
automatically search for any
Network Storage Link that is
currently on your network or
attached to your PC. If it fails to
detect the Network Storage
Link or if an Network Storage
Link has been installed since
the Setup Wizard’s last search,
click Search Again to locate
the Network Storage Link.
Select the Network Storage Link
that you want to set up. Then
click the Yes button to change
any of the Network Storage
Link’s settings.
DYou will be asked for your
password. For security
purposes, enter the current
password for the Network
Storage Link. The default is
admin. Click OK.
C
2Set up the Network Storage Link
D
6
AThe IP Settings screen will
appear. If you already have a
router or other DHCP server
automatically assigning IP
addresses, then select
Automatically obtain an IP
address (DHCP) and click Next.
Proceed to Step F.
If you want to set the Network
Storage Link’s IP address and
network information, then
select Set IP configuration
manually and enter the
following information:
• IP Address. Enter the Network
Storage Link’s IP address, and
make sure that it is on the
same local area network
(LAN) segment as the PC
running the Setup Wizard.
• IP Mask. Enter the Subnet
Mask, which must match the
subnet mask of the other
devices on your network. The
default is 255.255.255.0.
• Gateway. This field is left
blank by default. However, if
you have a router on your
network, enter its IP address in
this field.
Click the Next button.
E
7
AOn the Date/Time Settings
screen select your local time
zone. Then set the current date
and time. Click Next.
BReview the Network Storage
Link’s settings. If they are
correct, click Save. If you would
like to change them, click Back
to return to a previous screen.
CA screen will appear and ask
you to confirm that you want to
save new settings. To save
these changes, click OK, or
click Cancel to return to the
previous screen.
DIf the USB hard disk drive was
not previously used with a
Network Storage Link, then its
format must be changed. The
message shown in Figure I will
be displayed. To change the
USB hard disk drive's format so
that it can be used in the
Network Storage Link, click OK.
To leave the USB hard disk drive
unchanged, click Cancel, and
you will not be able to store
data on the hard disk drive.
F
G
IMPORTANT:The Network Storage
Link’s format is NOT compatible with
Windows. You cannot swap USB hard
disk drives between Windows systems
and Network Storage Links.
H
I
8
AOn the Congratulations
screen, click Exit to exit the
Setup Wizard.
Congratulations! The installation of
the Network Storage Link
is complete.
NSLU2-QIG-UK-40610NC KL
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2004
Cisco Systems, Inc. All rights reserved.
J
For additional information or troubleshooting
help, refer to the User Guide on the CD-ROM
or the Technical Support Insert. You can also
e-mail for further support.
Website
http://www.linksys.com/international
Modelnr.
Installationsvejledning
A Division of Cisco Systems, Inc.
®
WIRED
NSLU2 (DK)
Network Storage Link
Pakkens indhold
• En NSLU2 - Network Storage Link til
USB 2.0-diske
• En strømforsyning
• Et Ethernet-kabel på 2 meter
• En cd-rom med guidet konfiguration
og brugervejledning (kun på engelsk)
i pdf-format
• En installationsvejledning
• Et enhedsstativ
til USB 2.0-diskdrev
2
1Tilslut Network Storage Link
ASlut det medfølgende
Ethernet-kabel til Ethernet-
porten på Network Storage
Link. Slut derefter den anden
ende af kablet til din hub eller
switch.
BTilslut USB-lagerenhederne.
Hvis du bruger en USB-
flashhukommelse (USB Key),
skal du slutte den til Disk 2-
porten.
Denne installationsvejledning beskriver, hvor du fysisk skal slutte Network
Storage Link til netværket, og hvordan du skal konfigurere Network Storage
Link til basisdrift.
Inden du installerer Network Storage Link, skal du kontrollere, at disse krav
overholdes:
• TCP/IP-protokol skal være installeret på dine pc'er
• en port skal være tilgængelig på en hub eller switch (for tilslutning til
netværket)
• du skal have et USB-flashdrev og/eller en USB-harddisk (til lagring af
data)
Hvis disse krav overholdes, kan du fortsætte til trin 1.
A
B1
BEMÆRK: Flashdrevet skal sluttes
til Disk 2-porten. Det vil ikke fungere,
hvis du slutter det til Disk 1-porten.
VIGTIGT: Network Storage Link er
ikke ”hot-swappable”. Kontroller, at
der er slukket for Network Storage
Link, før du tilslutter eller frakobler et
USB-flashdrev eller en harddisk.
Other manuals for NSLU2 - Network Storage Link NAS Server
4
Table of contents
Languages:
Other Linksys Storage manuals
Linksys
Linksys NAS200 User manual
Linksys
Linksys WCF12 - Wireless-B Network CompactFlash Card Original operating instructions
Linksys
Linksys NSS4100 - Gigabit Storage System Operation manual
Linksys
Linksys NMH Series User manual
Linksys
Linksys NMH Series User manual
Linksys
Linksys NAS200 Operation manual
Linksys
Linksys NAS200 User manual
Linksys
Linksys NSS4000 Series Service manual
Linksys
Linksys NSS4100 - Gigabit Storage System User manual
Linksys
Linksys WCF12 - Wireless-B Network CompactFlash Card User manual
