Lightolier C6CW SERIES User manual

GASKET

CLEAT

MULLION

OUTLET BOX SCREWS

MOUNTING PLATE

CANOPY

1/4-20 BOLTS

CLEAT

FIG. 1 FIG. 2

FIG. 3

FIG. 4

CAUTION: For wet locations, in accordance with Underwriters Laboratories

requirements, a line of caulking compound such as acrylic or silicone must be

placed around the perimeter of CANOPY to seal water away from the

outlet box and back openings.

INSTALLATION OF WALL CYLINDER TO OUTLET BOX

(Fig. 1, 2, 3, & 4)

STEP 1: Attach MOUNTING PLATE to outlet box with OUTLET BOX

SCREWS.

STEP 2: Pass supply leads through opening in CANOPY and CLEAT.

STEP 3: Attach CANOPY, CLEAT/GASKET to MOUNTING PLATE with (2)

¼-20 BOLTS.

STEP 4: Make Connections. Bare Copper and/or green insulation wire(s)

must be connected to SUPPLY GROUND. Connect WHITE BALLAST LEAD

to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to

HOT SUPPLY LEAD. Use wire nuts (local hardware items).

STEP 5: Install SET SCREWS loosely. Place cylinder over CLEAT and

tighten (2) SET SCREWS.

INSTALLATION OF WALL CYLINDER TO POST OR OTHER

VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)

STEP 1: CLEAT can also be mounted directly to any flat surface

such as MULLION. In this case, use of CANOPY is optional. Bring

supply leads through CLEAT and install CLEAT to wall. For wet

locations, in accordance with Underwriters Laboratories requirements,

a line of caulking compound such as acrylic or silicone must be

placed around the perimeter of EXTRUDED ARM to seal water away

from the wireway and back openings.

STEP 2: Proceed with Step 4 and 5 above.

INSTALLATION OF REFLECTOR TRIM TO CYLINDER (Fig. 4)

Follow installation instructions in Reflector Trim Instruction Sheet IS:C4T4V.

CAUTION:

 DO NOT ENERGIZE THE LAMP UNTIL REFLECTOR

TRIM IS COMPLETELY INSTALLED.

 INSTALL ONLY T-6 TUBULAR SINGLE-ENDED

CREAMIC ARC TUBE METAL HALIDE LAMP.

A COMPANY

631 Airport Road, Fall River, MA 02720

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain

these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:C6CW

Page 1 of 2

A0604

INSTALLATION PROCEDURE FOR: C6CW SERIES 6” DIA. H.I.D. WALL MOUNT CYLINDER

USED WITH C6T6V SERIES FLANGLESS REFLECTOR TRIM (ORDER SEPARATELY)

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURES’ REFLECTOR

TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

APERTURE CONE

ASSEMBLY

FIG. 5

TO REPLACE BALLAST (Fig. 5 & 6)

Before changing the ballast, switch off the main power supply to the fixture.

STEP 1: Remove APERTURE CONE ASSEMBLY from REFLECTOR

HOUSING by grasping inside of cone and pulling down.

STEP 2: Remove lamp.

STEP 3: Pull REFLECTOR HOUSING down until CLIPS stop at the bottom

lip of LOWER HOUSING. Press CLIPS inward to remove REFLECTOR

HOUSING.

STEP 4: Detach LAMPHOLDER from REFLECTOR HOUSING by

squeezing LAMPHOLDER SPRING.

STEP 5: Remove WING NUTS, then separate UPPER HOUSING from top

of Lower HOUSING to access BALLAST/PLATE ASSEMBLY.

STEP 6: Turn SCREW counterclockwise to lossen SUPPORT BRACKET.

Repeat with other (2) screws. Carefully remove BALLAST/PLATE

SSEMBLY from UPPER HOUSING.

STEP 7: Detach BALLAST SUPPORT BRACKET by removing (2)

BALLAST SUPPORT BRACKET SCREWS.

STEP 8: Replace BALLAST. Reattach BALLAST/BALLAST SUPPORT

BRACKET, BALLAST/PLATE ASSEMBLY to UPPER HOUSING.

STEP 9: Align STUDS with holes in LOWER HOUSING, then tighten firmly

with WING NUTS.

STEP 10: Reverse installations from Step 4 to Step 1. For additional

instructions if needed, see Reflector Trim Instruction Sheet IS:C4T4V.

TO REPLACE LAMP (Fig. 5 & 6)

Before replace the lamp, switch off the main power supply to the fixture.

STEP 1: Remove APERTURE CONE ASSEMBLY from REFLECTOR

HOUSING by grasping inside of cone and pulling down.

STEP 2: Replace lamp. Follow lamp manufacturer’s directions for proper

care and handing of lamp.

STEP 3: Replace cone into reflector housing.

A COMPANY

631 Airport Road, Fall River, MA 02720

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:C6CW

Page 2 of 2

A0604

INSTALLATION PROCEDURE FOR: C6CW SERIES 6” DIA. H.I.D. WALL MOUNT CYLINDER

USED WITH C6T6V SERIES FLANGLESS REFLECTOR TRIM (ORDER SEPARATELY)

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURES’ REFLECTOR

TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

Table of contents

Other Lightolier Light Fixture manuals

Lightolier

Lightolier WX4 User manual

Lightolier

Lightolier Calculite ProSpec PB3H3070 User manual

Lightolier

Lightolier Lytecaster 2000AIC User manual

Lightolier

Lightolier Prospec 26190 User manual

Lightolier

Lightolier Coffaire II CFA2GPF217 User manual

Lightolier

Lightolier Lytecel LIS6G20LW132 User manual

Lightolier

Lightolier Lytespan 7515 User manual

Lightolier

Lightolier 4X4 MATRIX SERIES Instructions for use

Lightolier

Lightolier Calculite DD User manual

Lightolier

Lightolier Coffaire II CFH1GPF User manual

Lightolier

Lightolier Tangent FXT4P User manual

Lightolier

Lightolier Calculite DR User manual

Lightolier

Lightolier Lytecaster 1100AICM User manual

Lightolier

Lightolier 1101FIC User manual

Lightolier

Lightolier Lytecaster 1129 User manual

Lightolier

Lightolier Pendalyte 404722XU3 User manual

Lightolier

Lightolier 40750UC User manual

Lightolier

Lightolier MD*COFFER MDCG2BX User manual

Lightolier

Lightolier Lytecaster 1062LV User manual

Lightolier

Lightolier Calculite ProSpec PA3A7050 User manual

Lightolier

Lightolier Calculite C6T6VN User manual

Lightolier

Lightolier VRB SERIES 1'x4 User manual

Lightolier

Lightolier Lytecaster 384X User manual

Lightolier

Lightolier Lytecaster 1024 User manual

Popular Light Fixture manuals by other brands

Emos

Emos CLASSIC ZY1431T manual

Westinghouse

Westinghouse Outdoor Lighting Fixture owner's manual

Hedler

Hedler C 12 silent Operation manual

Blizzard Lighting

Blizzard Lighting Puck: CSI manual 

Energetic Lighting

Energetic Lighting ELYSL-5004 Series installation instructions

Lightmaxx

Lightmaxx Shaft 5R user manual

Triarch

Triarch 31083 Assembly instructions

Philips

Philips 32614 Series user manual

IKEA

IKEA TIVED Assembly instructions

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH user manual

Martin

Martin MAC 250 Krypton user manual

Cooper Lighting

Cooper Lighting Halo L3232E Specification sheet

Stageline

Stageline ODW-2410RGBW instruction manual

Light Sky

Light Sky Tornado Series user manual

ArtFox

ArtFox Beam 15R extreme manual

GLG

GLG multispot 330 user manual

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Assembly instructions

SELF Electronics

SELF Electronics FLEX instruction manual