Life Span SP700 User manual
Product may vary slightly from the item pictured due to model upgrades
Read all instructions carefully before using this product. Retain this owner’s manual for
future reference.
SP700 OWNER’S MANUAL
2
SP700
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS 3
2. EXPLODED DIAGRAM 5
3. PARTS LIST 7
4. ASSEMBLY INSTRUCTIONS 9
5. ADJUSTMENT 12
6. EXERCISE GUIDE 13
7. WARRANTY REGISTRATION 15
3
SP700
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this spinning bike.
It is important your spinning bike receives regular maintenance to prolong its useful life. Failing to
regularly maintain your spinning bike may void your warranty.
1. Keep children and pets away from the Spinning Bike at all times. DO NOT leave
unattended children in the same room with the machine.
2. Handicapped or disabled persons should not use the Spinning Bike without the
presence of a qualified health professional or physician.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Before beginning training, remove all within a radius of 2 meters from the machine. DO
NOT place any sharp objects around the Spinning Bike.
5. Position the Spinning Bike on a clear, level surface away from water and moisture.
Place mat under the unit to help keep the machine stable and to protect the floor.
6. Use the Spinning Bike only for its intended use as described in this manual. DO NOT
use any other accessories not recommended by the manufacturer.
7. Assemble the machine exactly as the descriptions in the instruction manual.
8. Check all bolts and other connections before using the machine for the first time and
ensure that the trainer is in the safe condition.
9. Hold a routine inspection of the equipment. Pay special attention to components which
are the most susceptible to wear off, i.e. connecting points and wheels. The defective
components should be replaced immediately. The safety level of this equipment can
4
SP700
only be maintained by doing so. Please don't use the Spinning Bike until it is repaired
well.
10.NEVER operate the Spinning Bike if it is not functioning properly.
11.This machine can be used for only one person’s training at a time.
12.Do not use abrasive cleaning articles to clean the machine. Remove drops of sweat
from the machine immediately after finishing training.
13.Always wear appropriate workout clothing when exercising. Running or aerobic shoes
are also required.
14.Before exercising, always do stretching first.
15.The power of the machine increases with increasing the speed, and the reverse. The
machine is equipped with adjustable knob, which can adjust the resistance.
WARNING: BEFORE BEGINNING THIS OR ANY EXERCISE PROGRAM,
CONSULT YOUR PHYSICIAN F I R S T. THIS IS ESPECIALLY IMPORTANT
FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-
EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE
USING THE SPINNING BIKE. THANE ASSUMES NO RESPONSIBILITY FOR
PERSONAL INJURY OR PROPERTY DAMAGE SUSTA I N E D BY OR
THROUGH THE USE OF THIS PRODUCT
5
SP700
2. EXPLODED DIAGRAM
6
SP700
56
57
58
59
60
57
57
61
42
53
53
51
39
29
33
49
50
54
42
64
65
38 37 33
26
27
28
39
29
40
30
31
41
22
33
35
68
67
66
26
42
62
63
45
46
47
48
10
33
52
55
32
43
51
44
36
34
70
71
7
SP700
3. PARTS LIST
NO NAME QUANTITY SPEC
1 STOPPER 4 φ40*35/(M8X25)
2NUT 4
GB/T 41-2000 M8
3 CARRIAGE BOLT 4 GB/T 12-1988 M8*55
4 REAR STABILIZER 1 WELDING
5 END CAP 1 4 配80*40*1.5管
6 FLAT WASHER 4
GB/T 95-2002 8
7 DOMED NUT 4 GB/T 802-1988 M8
(H=16mm)
8 PEDAL 1 YH－21X（9/16"）
9 FRONT STABILIZER 1 WELDING
10 MAIN FRAME 1 WELDING
11 L SHAPE KNOB 4 M10*23
12 FIXING NUT 2 Q235/32*12
13 FIXING SHAFT 1 φ22*19
14 END CAP 2 1 70*30*1.5
15 FLAT WASHER 1 2 φ45*φ10.5*5
16 VERTICAL SEAT POST 1 WELDING
17 SEAT POST 1 WELDING
18 SEAT 1 DD-2681
19 HANDLEBAR POST 1 WELDING
20 BOLT 1 2
GB/T 5780-2000 M8*40
21 WHEEL 2 φ69X26
22 LOCK NUT 6 GB/T 889.1-2000 M8
23 FIXING SHAFT1 1 φ22*21
24 END CAP 1 38*38*1.5
25 HANDLE BAR 1 WELDING
26 SCREW 8 GB/T 15856.1-2002 ST4.2X16
27 OUTER CHAIN COVER 1 572*249*52
28 BELT 1 5PK1180MM
29 FIXING NUT 1 2
GB/T 6177.2-2000 M10*1.25
30 RIGHT CRANK 1 170*27
31 CHAIN WHEEL 1 φ200*24
32 INNER CHAIN COVER 1 336*242*3
33 BEARING 4 6004ZZ
34 AXIS 1 φ20*156
35 SHORT FIXING TUBE 1 φ25*2.5*9
36 LONG FIXING TUBE 1 φ25*φ20.5*41
8
SP700
NO NAME QUANTITY SPEC
37 FIXING NUT 1 φ28*M20*1
38 LEFT CRANK 1 170*27
39 CRANK END CAP 2 φ23*7.5
40 BOLT 2 4 GB/T 70.3-2000 M8*15
41 SCREW 1 4
GB/845-85 ST4.2X9.5
42 BOLT 3 5 GB/T 70.1-2000 M6*35
43 LEFT LITTLE COVER 1 249*237*23.5
44 RIGHT LITTLE COVER 1 249*230*26
45 SHAFT 1 φ25*42
46 BEARING 2 6203ZZ
47 FLAT WASHER 1 1 GB/T 95-2002 10
48 SHAFT NUT 1 φ18*11
49 SHAFT SLEEV 1 φ28*φ19*5
50 LITTLE CHAIN WHEEL 1 φ64*23
51 FLYWHEEL HOLDER 2 129*56.5*15
52 FLYWHEEL SHAFT 1 φ49*77.5
53 FLAT WASHER 2 8
GB/T 95-2002 6
54 CNC FLYWHEEL 1 φ460*15(20KG)
55 BOLT 4 4 GB/T 70.1-2000 M6*12
56 NUT 1 2
GB/T 41-2000 M6
57 BOLT 5 4 GB/T 70.1-2000 M6*12
58 ADJUSTING METAL 1 156*14.5*δ1.5
59 BLOCK 1 161*21*19
60 WOOLLY BLOCK 1 155*15.5*6
61 BOLT 6 2 GB/T 5780-2000 M5*10
62 NUT 2 1 φ16*14
63 SPRING 1 1 φ1.0X55
64 PLASTIC SLEEVE 1 45*45*1.5
65 TENSION CONTROL KNOB 1 M10*225
66 BREAK COVER 1 95*70*38.5
67 SPRING 2 1 δ1.8X40
68 FIXING NUT2 1 15.5*15.5*δ5（M10)
69 PLASTIC SLEEVE 1 1 80*40*1.5
70 CRANK COVER 1 φ56*28
71 BOLT 7 1 GB/T 70.1-2000 M6*20
72 HAND SUPPORT 2 120*65
73 STICKER 2 100*55
74 BOLT5 4GB/T 70.3-2000 M6*18
75 SUPPORT SHEET 2δ2
76 COMPUTER 1 JS-204
77 SENSOR 1L＝120
9
SP700
4. ASSEMBLY INSTRUCTIONS
STEP 1: PREPARATION
A. Before assembling make sure that you will have enough space around the item.
B. Use the present tooling for assembling.
C. Before assembling please check whether all needed parts are available (at the above of this instruction
sheet you will find an explosion drawing with all single parts (marked with numbers) which this item
consists of.
STEP 2:
1. Remove the bolts and nut from the
bottom tube
2. Attach the Front Stabilizer (pt.9) to the
Main Frame (pt.10) using two sets of
Ø8 Flat Washers (pt.6), M8 Domed Nut
(pt.7) and M8*55 Carriage bolt (3).
3. Attach the Rear Stabilizer (pt.4) to the
Main Frame (pt.10) using two sets of
Ø8 Flat Washers (pt.6), M8 Domed Nut
(pt.7) and M8*65 Carriage bolt (3).
10
SP700
STEP 3:
STEP 4:
1. Slide the Vertical Seat Post (pt.16) into
the seat post housing on the main frame
(pt.10).
2. Slide the Seat Post (pt.17) into the
Vertical Seat Post (pt.16),then Secure
using a flat washer 1 (15) and L Shape
knob (11).You will have to slacken the
knurled section of the L Shape Knob
(pt.11) and pull the knob back and then
select the desired height. Release the
knob and retighten the knurled portion.
3. Now fix the Seat (pt.18) to the Seat
Post (pt.17) as shown, and tighten the
bolts around the screws under the seat.
1. Slide the Handlebar Post (pt.19) into
the handlebar post housing on the main
frame(pt.10). You will have to slacken
the knurled section of the L Shape
Knob (pt.11) and pull the knob back
and then select the desired height.
Release the knob and retighten the
knurled portion.
2. Fix the Handlebar (pt.25) with a flat
washer 1 (15) and L Shape knob (11)
ATTENTION: YOU SHOULD FIX THE
HANDLEBAR TIGHTLY
Table of contents
Other Life Span Exercise Bike manuals
Life Span
Life Span EXER-58 User manual
Life Span
Life Span EXC-100 User manual
Life Span
Life Span EXER-80 User manual
Life Span
Life Span RBX-100 User manual
Life Span
Life Span DT-3C User manual
Life Span
Life Span R5i User manual
Life Span
Life Span LFE01 Cyclestation 3 User manual
Life Span
Life Span RC 99 User manual
Life Span
Life Span X-03 User manual
Life Span
Life Span R3 User manual
Life Span
Life Span RC-81 User manual
Life Span
Life Span SP750 User manual
Life Span
Life Span Ampera Office Bike User manual
Life Span
Life Span SP-300 User manual
Life Span
Life Span XT-35 User manual
Life Span
Life Span RC 80 User manual
Life Span
Life Span C3-DT User manual
Life Span
Life Span SP-650 User manual
Life Span
Life Span SM-410 User manual
Life Span
Life Span R7000i User manual
