LG LD-4204T1 User manual
DISHWASHER
Please read this manual carefully before operating your
dishwasher. Retain it for future reference.
OWNER'S MANUAL
MODEL : LD-1420T1
MFL30149772 2009.2.24 8:55 AM ˘`1 ‰¯¿ł–•¡˙¨‰”
ONTENTS
C
SAFETY AND CAUTION 3
INSTALLATION INSTRUCTIONS 5
PARTS NAME 9
FUNCTION OF CONTROL BUTTON 10
BEFORE USING FOR THE FIRST TIME 12
HOW TO USE AND OPERATE 13
OPERATING SEQUENCE 18
PROGRAM 19
USER MAINTENANCE INSTRUCTIONS 20
TROUBLE SHOOTING GUIDE 21
SPECIFICATION
MFL30149772 2009.2.24 8:55 AM ˘`2 ‰¯¿ł–•¡˙¨‰”
3
AFETY AND CAUTION
S
• Please read this manual carefully before using
the dishwasher for the first time.
• This manual contains very important notes
regarding the installation, use and maintenance
of your dishwasher.
• The manufacturer can not be responsible for
problems caused by ignoring these safety and
caution instructions.
• This dishwasher is designed for normal
household use.
• Do not use the dishwasher for industrial and
commercial use, or other purpose.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Check packaging and dishwasher immediately
for signs of transport damage. If the appliance
is damaged, do not put it into use but contact
your supplier without delay.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
During installation
• Electrical connection must be in accordance
with the rating label.
• Electrical safety is only guaranteed when the
earth system of your house is in accordance
with the related local regulations.(Do not use
an extension cable or cord.)
• If the hot water exceeds 65ºC, adjust the water
heater setting. If the hot water temperature can
not be maintained below 65ºC, the dishwasher
must be connected to cold water.
• If power supply cord is damaged, it must only
be replaced by the manufacturer or its service
agent or a similar qualified person in order to
avoid a hazard.
• This appliance must be positioned so that the
plug is accessible.
• The appliance is to be connected to the water
mains using new hose-sets and that old hose-
sets should not be reused.
• The door should not be left in the open
position since this could present a tripping
hazard
During use
• Only suitable household utensils should be
placed in the dishwasher.
(Please avoid utensils; that are non-
heatresistant, metal decorated, etc.)
• Do not use any kinds of solvent in your
dishwasher. They may cause an explosion or
fire.
• Do not spray water on the appliance.
It may cause the failure of electric parts or
electric shock.
• Do not push down or sit on the inner door
when the door opened. It may cause the
deformation or failure of your dishwasher.
• Do not use the detergent for hand washing.
The detergent for dishwasher should be used
for normal operation.
• This appliance is fitted with a safety function
that automatically stops the operation of the
dishwasher when it is exposed to heavy
disturbance on its mains.
• Dishwasher detergents are strongly alkaline.
They can be extremely dangerous if
swallowed. Avoid contact with skin and eyes
and keep children away from the dishwasher
when the door is open.
Check that the detergent receptacle is empty
after completion of the wash cycle.
Child Safety
• Controls may be locked using “Child Lock”
mode to prevent from all the setting from
being changed by a child.
• Keep children away from detergents and rinse-
aids.
• Do not allow children to operate the
dishwasher.
• Young children should be supervised to ensure
that they do not play with the appliance.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
- When using your dishwasher, follow basic precautions,
including the following:
MFL30149772 2009.2.24 8:55 AM ˘`3 ‰¯¿ł–•¡˙¨‰”
AFETY AND CAUTION
S
4
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown, grounding
will reduce the risk of electric shock by providing a path of least resistance for electric
current. This appliance is equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is installed
and grounded in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or service
representative if you are in doubt whether the appliance is properly grounded.
Do not modify the plug provided with the appliance; if it will not fit the outlet
have a proper outlet installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the
cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the appliance.
CAUTION
MFL30149772 2009.2.24 8:55 AM ˘`4 ‰¯¿ł–•¡˙¨‰”
5
NSTALLATION INSTRUCTIONS
I
Unit:mm
Step 1 :
PREPARE CUPBOARD OPENING Step 2 :
PREPARATION FOR ELECTICAL WIRING
1
2
3
This appliance must be supplied with
correct rating voltage and hertz as shown
on instruction manual, and connected to
an individual, properly earthed branch
circuit, protected by a minimum 15 amp
circuit breaker or time delay fuse.
Wiring must be 2 wire with Earth.
The power plug must be in a accessible
location adjacent to and not behind the
dishwasher and within 1.2 meters of the
dishwasher side.(See page 7 Fig.A)
The power plug must be correctly
earthed, if in doubt, have it checked by a
qualified Electrician. No other appliance
should be connected to the same plug
outlet by a double adapter or similar
plug.
CAUTION
For personal safety, remove house
fuse or open circuit breaker before
installation. Do not use an extension
cord or adapter plug with this
appliance. Electrical and earthing
connections must comply with the
national electrical code/provincial and
municipal code and/or other local
codes.
Any bare wood surrounding the
dishwasher should be sealed with a
waterproof paint or sealant to prevent
swelling.
WARNING
A qualified electrician/plumber or competent person should carry out any electrical/plumbing
work required to install this appliance.
1
2
3
4
This dishwasher is designed to fit the size
shown as below.
Select a location as close to sink as
possible for ease of connection to the
water and drain pipes.
To ensure good drainage, the dishwasher
should not be installed more than 3 meters
away from the sink.
If dishwasher is installed in a corner, a
minimum of 5cm of space is required
between the washer and an adjacent
cabinet or wall.
MFL30149772 2009.2.24 8:55 AM ˘`5 ‰¯¿ł–•¡˙¨‰”
NSTALLATION INSTRUCTIONS
I
6
Step 3 :
PREPARING THE DISHWASHER
FOR INSTALLATION
1
2
Lay the dishwasher on its back.
Adjust the legs to the required height
as shown in below figure.
Step 4 :
INSTALLING THE
DISHWASHER IN CUPBOARD
1
2
Before sliding the dishwasher into the
cupboard opening, all necessary height
and balancing adjustments should be
made using a spanner.
Slide the dishwasher into the cabinet
opening carefully. Make sure that the
drain hose inside the cabinet is not
kinked or stretched.
CAUTION
If the height of the cupboard is below
850mm, you should remove the top table
by unscrewing the 2 screws. (Two of rear)
Adjust
leg
MFL30149772 2009.2.24 8:55 AM ˘`6 ‰¯¿ł–•¡˙¨‰”
7
NSTALLATION INSTRUCTIONS
I
Step 5 :
DRAIN LINE CONNECTION
1
2
3
If the end of drain hose does not fit to
the drain line, use a rubber
connector(not supplied) that is
resistant to heat and detergent.
This should be available from a
plumbing shop or DIY merchants.
There are two typical connections as
shown in Figure A, B.
The “S” trap spigot must be drilled out
cleanly and free of obstruction to its
maximum internal diameter, if used for
drainage.
To prevent siphoning, one of the following
methods must be used:
When the drain hose is connected to a
sink “s” trap or waste disposal unit, the
hose must be looped up to the underside
of the bench top and secured.
When the drain hose is connected to a
separate standpipe, it is essential that an
airtight connection be made.
Refer to Fig.B
Drain hose Extension
Extend drain hose as shown below.
Fig. A
Fig. B : Drainage connection - stand pipe.
CAUTION
When you connect or extend drain hose,
make sure that drain hose is not kinked.
(Bends should have a 40 mm radius.)
MFL30149772 2009.2.24 8:55 AM ˘`7 ‰¯¿ł–•¡˙¨‰”
NSTALLATION INSTRUCTIONS
I
8
Step 6 :
WATER SUPPLY CONNECTION
1
2
Connect the water supply hose to the
water tap as shown.(Some models
consist of an inlet valve and hose.)
This dishwasher may be fed with either
hot or cold water. If the water can not be
maintained below 65ºC, the dishwasher
must be connected to cold water.
When connecting, the sealant tape or
sealing compound to avoid water leaks.
Make sure that the line is not kinked or
sharply bent.
Step 7 :
FINAL CHECK AND ASSEMBLING
1
2
Securely hand tighten supply hose to the
water supply.
Plug the power supply cord into an earthed
electrical point and switch on.
After installing and prior to using the
dishwasher with crockery, we recommend
that you use the dishwasher on ‘Quick’
mode to rinse through. At this stage it is
useful to ensure that there are no operating
problems or water leaks.
When the dishwasher is used for the first,
there may be a loud noise, if this happens,
turn off the power and restart the
dishwasher.
Step 8 :
HOW TO LEVEL THE DISHWASHER
After installing the dishwasher, you may
notice a slight sticking of the door to the
dishwasher, when you open or close the door.
If this does happen you need to adjust the level
of the dishwasher.
• If the door slants to the right, see fig, C and
follow these instructions:
1) Unscrew(counter-clockwise) the left leg of
the back side and correct the level.
2) Check the opening of door and repeat if
necessary until the door opens and closes
properly.
• When the product is correctly leveled, There
should be no slant , stickiness or friction
sound.
• If the door slants to the left, see fig. D and
follow these instructions:
1) Check the opening of door if there still
remains sticky or friction sound.
2) Check the opening of door and repeat if
necessary until the door opens and closes
properly.
• When the product is correctly leveled, There
should be no slant , stickiness or friction
sound.
Fig. C
Fig. D
Case 1. In case the door is slanted to the right
Case 2. In case the door is slanted to the left
MFL30149772 2009.2.24 8:55 AM ˘`8 ‰¯¿ł–•¡˙¨‰”
9
ARTS NAME
P
1. Control Panel
2. Door Handle
3. Front Cover
4. Lower Cover
5. Display Window
6. Power Button
7. Drain Hose
8. Inlet Hose
9. Power Cord
10. Adjustable Leg
11. Upper Rack
12. Cutlery Rack
13. Detergent And Rinse Aid Dispenser
14. Vapor Vent Cover
15. Upper Spray Arm
16. Lower Spray Arm
17. Filter ASM
18. Lower Rack
MFL30149772 2009.2.24 8:55 AM ˘`9 ‰¯¿ł–•¡˙¨‰”
UNCTION OF CONTROL BUTTON
F
10
Program
Program
• To select a program, press this button.
UV
• If you want to sterilize the dishes, press UV button.
• After drying cycle, the UV lamp will turn on to perform the sterilization function.
Indicator
• Child Lock.
• Refill with rinse aid.
Time Left
• Before starting, the display window shows the running time of the selected program.
• After starting, the display window shows the remaining time.
• If the dishwasher has a trouble, the trouble type is displayed.
“OE”, “FE”, “IE”, “EI”, “HE”, “CE”, “LE”, “tE”
• If this error letters are displayed, please refer to the trouble shooting guide page 22 and follow the guide.
Beep On/Off
• The dishwasher must be switched on.
• The beep on/off function can be set by pressing the Half Load and Spray button simultaneously for a few seconds.
Then, a “On” will appear in the display.
• The beep on/off function is automatically canceled when power failure occur.
MFL30149772 2009.2.24 8:55 AM ˘`10 ‰¯¿ł–•¡˙¨‰”
This manual suits for next models
1
Table of contents
Other LG Dishwasher manuals
LG
LG LDF7932WW User manual
LG
LG LDP679# series User manual
LG
LG SDWB24W3 User manual
LG
LG LDT680 Series User manual
LG
LG DFB227 Series User manual
LG
LG LDF9932 User manual
LG
LG LDT7808ST User manual
LG
LG LDF6920WW User manual
LG
LG LDF9810ST - Fully Integrated 6 Wash Cycles... User manual
LG
LG LDF567 Series User manual
