LevelOne IGP-0802 User manual

IGP-0802

8-Port Industrial Gigabit Ethernet PoE Switch,

8PoE Outputs, 802.3at PoE+, 200W

User Manual

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received; including interference that may

cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55022 class A for ITE, the essential protection requirement of

Council Directive 2004/108/EC on the approximation of the laws of the Member States

relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible that

information in this document is not up-to-date. Please check with your local

distributors for the latest information. No part of this document can be copied or

reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Power connection:

This industrial Fast Ethernet 8 port POE switch is equipped with 4 x 10/100/1000M PSE port, each port can

deliver 30W POE power. It comes with a 6 pin terminal block. It can be connected with 48-56VDC power

source. Always Make sure to use 56VDC for IEEE802.3at or 30W power connection.

WARNING –any exceeded input voltage will not make this unit function and may damage this unit.

To make power connection –Follow the printed polarity for V1+, V1-,

V2+, V2-, and ground. Connect positive wire to V+ , connect negative

wire to V-, also connect neutral wire to the ground screw as shown .

Relay -- You may use 24V@1A relay connection to your external

device for special purpose. When 2 powers are connected, the relay is

in OPEN mode. When any power source fails, the relay change to

SHORT status.

Power connecting procedure:

STEP 1 –Pull out 6 pin terminal block.

STEP 2 –Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.

STEP 3–Plug back 6 pin terminal block to its place.

WARNING –

Always ground the power source to maintain a clean power input. Due to too many cheap made power

supplies, it creates too much noise, and it will cause the power input fluctuates when connect to this

unit. To avoid this, always ground the power source to gain a clean power input.

Din Rail Bracket x 1

Wall mount bracket x 2

6 pin Terminal Block x1

Installation package:

This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted

bracket are included.

LED indicator:

PW1

ON -- when V1+, V1- is connected

PW2

ON -- when V2+, V2- is connected

Green LED ---

ON =Link

Flash = TX/RX.

Relay LED Amber

ON one power is connected

OFF two powers are connected

Amber LED ---

ON = POE detected

OFF = POE not detected

Flash = POE detecting.

Specification:

IEEE Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet

IEEE 802.3z 1000Base-X Gigabit Ethernet

IEEE802.3x Flow Control and Back Pressure,

IEEE802.3af for POE

IEEE802.3at for POE+

Switch Architecture

Back-plane (Switching Fabric): 16Gbps

Data Processing

Store and Forward

Flow Control:

IEEE 802.3x Flow Control and Back Pressure

Jumbo Frame

9KB

MAC address Table Size

Packet Buffer Size

Network Connector :

8xRJ-45 10/100/1000BaseT(X) auto negotiation,

8x POE+ 802.3at/af PSE port

Auto MDI/MDI-X function, Full/Half duplex

Network Cable

UTP/STP above Cat.5e Cable

EIA/TIA-568 10-ohm (100m)

Protocol

CSMA/CD

LED

PW1(Power 1) Green,

PW2(Power 2) Green,

SW(relay) Amber,

TX/RJ-45 port:

LNK (Link/Active) Green,

Amber: POE Detected

Housing

Heavy Metal Housing

Reserve polarity protection

Present

Overload current protection

Present

Power Supply

Redundant Dual DC 48V-56V Power Input

POE input 48-56VDC

Power Consumption

5.76W@48 VDC full load, Without POE

Alarm Relay Contact

Relay outputs with current carrying capacity of 1 A

@24VDC,

Relay in short circuit mode when 2 powers are

connected. in open circuit mode when only one

power supply is connected

POE power

POE power per port 30watts. Maximum 36Watts

Maximum total power 200Watts with 56VDC input,

Supports IEEE802.3af/at

Removable Terminal Block

Provide 2 Redundant power , Alarm relay contact ,6

Wire range: 0.34mm^2 to 2.5mm^2

Solid wire (AWG):12-24/14-22

Stranded wire(AWG): 12-24/14-22

Torque:5lb-In/0.5Nm/0.56Nm

Wire Strip length: 7-8mm

Operating Temperature

-20℃~70℃fully tested. ( T model -40°C to 75°C

also available)

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40℃~85℃

MTBF (mean time between failure)

510,304 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Metal ,IP30 Protection

Case Dimension (L x W x D)

142mmx36.2mmx105mm (LxWxD)

Installation mounting

DIN Rail mounting and Wall Mounting

Certifications:

EN55022/24

ITE equipment

EN55011

Industrial, Scientific and Medical (ISM) equipment

Safety

IEC EN60950-1

EMC/EMS

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

EN 50155 / EN 60068-2-6

Vibration

EN 50155 / EN 60068-2-27

Shock

EN 50155 / EN 60068-2-32

Free Fall

Housing Dimension:

Table of contents

Other LevelOne Network Router manuals

LevelOne

LevelOne WBR-6600 User manual

LevelOne

LevelOne WBR-6004 User manual

LevelOne

LevelOne FNS-7000A User manual

LevelOne

LevelOne IES-0810 User manual

LevelOne

LevelOne GEL-2670 User manual

LevelOne

LevelOne IFE-0501 User manual

LevelOne

LevelOne GTL-2660 User manual

LevelOne

LevelOne WGR-8031 User manual

LevelOne

LevelOne WAC-2003 User manual

LevelOne

LevelOne IGP-0501 User manual

LevelOne

LevelOne DC-202 User manual

LevelOne

LevelOne GSW-0807 User manual

LevelOne

LevelOne WBR-6003 User manual

LevelOne

LevelOne FBR-1161 User manual

LevelOne

LevelOne WBR-3470 User manual

LevelOne

LevelOne MDU-2400FXC User manual

LevelOne

LevelOne FHU-0803TXD User manual

LevelOne

LevelOne POI-3000 User manual

LevelOne

LevelOne GSW-5150 User manual

LevelOne

LevelOne GEU-0807 User manual

LevelOne

LevelOne WBR-3600 User manual

LevelOne

LevelOne IGP-0521 User manual

LevelOne

LevelOne GSW-2473 User manual

LevelOne

LevelOne FSW-0511 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview