LevelOne GSW-5150 User manual

48-Port Fast Ethernet TP + 3-Port Gigabit Ethernet TP/SFP

GSW-5150

User's Guide

Ve r. 1 . 0 . 0 - 0 8 0 3

REV:1.0.0

71035980

Specications are subject to change without notice. Level One is a registered trademark of

Digital Data Communications Co., Ltd. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specications may be reproduced in any form or by any means or used to

make any derivative such as translation, transformation, or adaptation without permission

FCC STATEMENT

The 48-Port Fast Ethernet TP+ 3-Port Gigabit Ethernet TP/SFP Switch has been tested

and found to comply with the limits for a class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.



EC DECLARATION OF CONFORMITY (EUROPE)

In compliance with the EMC Directive 89/336/EEC, Low

Voltage Directive 73/23/EEC, this product meets the

requirements of the following standards:

EN55022

EN55024

EN60950

SAFETY NOTICES

Caution:

Do not use this product near water, for example, in a wet

basement or near a swimming pool.

Avoid using this product during an electrical storm. There

may be a remote risk of electric shock from lightning.



TABLE OF CONTENTS

Package Contents........................................................................................1

Chapter 1: Introduction of the Product.....................................................2

1.1 Overview of the product.........................................................................2

1.2 Features...............................................................................................................2

Chapter 2: Installation..................................................................................3

2.1 Mounting the Switch on a Desk..........................................................................3

2.2 Mounting the Switch in a Rack...........................................................................4

2.3 Mounting the SFP module..................................................................................5

2.4 Power on.............................................................................................................5

Chapter 3: Identifying External Components..........................................5

3.1 Front Panel..........................................................................................................5

3.2 Rear Panel...........................................................................................................6

Appendix A: Specications........................................................................7

GSW-5150 48-Port Fast Ethernet +3-Port Gigabit

Package Contents:

The following contents should be found in your box:

 One Switch

 One power cord

 This User's Guide

 Rubber footpads for Desk-mount

 Rack-mount kit for installing the switch in a 19-inch rack

Note:

If any of the above contents is damaged or missing, please contact the retailer

from whom you purchased the GSW-5150 Gigabit Ethernet Switch for assistance.

GSW-5150 48-Port Fast Ethernet +3-Port Gigabit

Chapter 1: Introduction of the Product

This chapter describes the features of the GSW-5150 Gigabit Ethernet Switch.

1.1 Overview of the product

The GSW-5150 Gigabit Ethernet Switch provides you with a high-performance,

low-cost, easy-to-use, seamless and standard upgrade to boost your old

network to 1000Mbps. Increase the speed of your network server and backbone

connections, make Gigabit connection to a server or uplink a network necessarily.

The GSW-5150 features a non-blocking switching architecture that forwards

and filters packets at full wire-speed for maximum throughput. MAC address

auto-learning and auto-aging, IEEE802.3x flow control for Full Duplex mode

and backpressure for Half Duplex mode. It is compatible with all 10,100, and

1000Mbps Ethernet devices because it is standard-based.

The GSW-5150 is plug-and-play and no conguration is required. Auto MDI/MDIX

cable detection on all ports eliminate the need for crossover cable or Uplink port.

Each port can be used as general ports or Uplink ports, and any port can be

simply plugged into a server, a hub, a router or a switch, using the straight cable

or crossover cable. Diagnostic LEDs which display link status and activity, allowing

you to quickly detect and correct problems on the network.

1.2 Features

 Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z standards

 48 10/100Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX

 2 10/100/1000Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX

GSW-5150 48-Port Fast Ethernet +3-Port Gigabit

 1 SFP(Small Form Pluggable) module interface



Supports Auto MDI / MDIX cable detection on all ports eliminate the need for

crossover cable or Uplink port.

 Non-blocking switching architecture that forwards and lters packets at fullwire

-speed for maximum throughput.

 Supports MAC address auto-learning and auto-aging



Supports IEEE802.3x ow control for full-duplex model and backpressure for

half-duplex transfer model



LED indicators for monitoring power, link, activity, speed

 Internal power supply

Chapter 2: Installation

2.1 Mounting the Switch on a Desk

Before place the Switch on a desk, attach four rubber footpads to the utes on the

Switch bottom, then lay the Switch on the desktop, where can be have as much as

5kg placed on top.

Note:

Make sure there is a grounded AC outlet within 1.5 meters, and working well.

Make sure there is free space for radiating heat and air.

Make sure not to place anything to heavy on top of the switch.

GSW-5150 48-Port Fast Ethernet +3-Port Gigabit

2.2 Mounting the Switch in a Rack

The dimension of GSW-5150 is designed according to the standard 19'' rack-

mountable steel case of Electronic Industries Association.

Turn off all the equipment connected to the Switch before mounting it in the rack,

then rivet the two ’ L’ brackets onto each side of the Switch, fasten it with screws in

the rack.

Figure 2-1 Rivet the ‘L’brackets onto the Switch

29 30 31 3233 34 35 363738 3940 41 4243 44 45 464748

246810 1214 1618 2022 242526 27 28

1357911 13 15 17192123

24681012141618202224262830323436384042444648

33353739414345

1357911131517272931

192123

SFP

Link/Act

GIGA1GIGA2

GIGA1

GIGA2

GSW-5150

48-Port Fast Ethernet TP+ 3-Port

Gigabit EthernetTP/SFP Switch

PWR

2930313233343536373839404142434445464748

2468101214161820222425262728

1357911131517192123

24681012141618202224262830323436384042444648

33353739414345

1357911131517272931

192123

SFP

Link/Act

GIGA1GIGA2

GIGA1

GIGA2

GSW-5150

48-PortFast EthernetTP+ 3-Port

GigabitEthernetTP/SFPSwitch

PWR

Figure 2-2 Fasten the Switch in the rack

GSW-5150 48-Port Fast Ethernet +3-Port Gigabit

2.3 Mounting the SFP module

The front panel of the GSW-5150 consists of a SFP module, which support The

Hot Plug- And- Draw. Should xed the SFP into SFP pluggable when use the SFP

module.The switch could identify and Cong the SFP module automatically.

2.4 Power on

GSW-5150 Switch is powered by AC power supply. Powering on the Switch, it will

automatically initialize and its LED indicators should respond as follows:

All of the LED indicators will ash momentarily for one second, which represent

a resetting of the system.

2) The power LED indicator will remain ON.

Chapter 3: Identifying External Components

This Chapter describes the front panel, rear panel and LED indicators of the

Switch.

3.1 Front Panel

The front panel of the GSW-5150 consists of switch LED indicators, 48

10/100Mbps RJ-45 ports ,2 10/100/1000Mbps RJ-45 ports and 1 SFP module.

Figure 3-1 GSW-5150 Switch Front Panel sketch

GSW-5150 48-Port Fast Ethernet +3-Port Gigabit

 LED indicators

The LED indicators include Power, Link/Act, 1000Mbps and 100Mbps LED

indicators, which are used for monitoring and pre-troubleshooting of the Switch.

The following section shows the LED indicators for the Switch along with an

explanation of each indicator.



Power LED: This indicator will light solid red when the Switch powers up. If the

LED is not lit, please check the power supply and connection.



1000M LED: The corresponding gigabit port LED indicator will light solid green

when the gigabit port connected to a 10/100/1000Mbps device. It ashes

green when data is being transmitted or received on the working connection.



100M LED: The corresponding 100M port LED indicator will light solid green

when the 10/100M port connected to a 100Mbps device. It flashes green

when data is being transmitted or received on the working connection.



SFP LED: The SFP LED indicates SFP module Link/Active status. The LED

indicator will light solid green when the SFP port connected correctly It ashes

green when data is being transmitted or received on the working connection.

3.2 Rear Panel

The rear panel of the GSW-5150 only features a power receptacle, which is an AC

power receptacle. Connect the female of the power cord head here, and the male

head to the AC power outlet.

10 0- 24 0V 5 0-6 0H z 0. 6A

Figure 3-2 GSW-5150 Switch Rear Panel sketch

Other manuals for GSW-5150

Table of contents

Other LevelOne Network Router manuals

LevelOne

LevelOne WGR-8031 User manual

LevelOne

LevelOne GSW-0507 User manual

LevelOne

LevelOne WAC-2003 User manual

LevelOne

LevelOne GEL-2461 User manual

LevelOne

LevelOne NetCon FBR-4000 User manual

LevelOne

LevelOne WBR-6603 User manual

LevelOne

LevelOne FSW-1650 User manual

LevelOne

LevelOne POI-3000 User manual

LevelOne

LevelOne WAC-2000 User manual

LevelOne

LevelOne PLI-2020 User manual

LevelOne

LevelOne GEU-2429 User manual

LevelOne

LevelOne NetCon WBR-3408 User manual

LevelOne

LevelOne GEU-0822 User manual

LevelOne

LevelOne FSW-0511 User manual

LevelOne

LevelOne FBR-1100TX User manual

LevelOne

LevelOne WBR-3470 User manual

LevelOne

LevelOne WAB-3000 User manual

LevelOne

LevelOne GBR-4001 User manual

LevelOne

LevelOne WBR-6801 User manual

LevelOne

LevelOne GSW-2457 User manual

LevelOne

LevelOne WBR-6003 User manual

LevelOne

LevelOne FBR-1700TX User manual

LevelOne

LevelOne PLI-2030 User manual

LevelOne

LevelOne FHU-0803TXD User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview