LevelOne FSW-1650 User manual

FSW-1650

FSW-2450

User Manual

16/24 10/100 Rackmount Switch

V3.0..0906

Specifications are subject to change without notice. LevelOne is a registered

trademark of Digital Data Communications Asia Co., Ltd. Other brands and

product names are trademarks or registered trademarks of their respective

holders.

No part of the specifications may be reproduced in any form or by any means or

used to make any derivative such as translation, transformation, or adaptation

without permission from Digital Data Communications Asia Co., Ltd. All rights

reserved.

FCC STATEMENT

The Switch has been tested and found to comply with the limits for a class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

¾Reorient or relocate the receiving antenna.

¾Increase the separation between the equipment and receiver.

¾Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

¾Consult the dealer or an experienced radio/TV technician for help.

EC DECLARATION OF CONFORMITY (EUROPE)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/

EEC, this product meets the requirements of the following standards:

¾EN55022

¾EN55024

¾EN60950

SAFETY NOTICES

Caution:

Do not use this product near water, for example, in a wet basement or near a

swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk

of electric shock from lightning.

Package Contents:

The following contents should be found in your box:

¾One FSW-1650 / FSW-2450 Switch

¾One power cord

¾This User's Guide

¾Mounting screws and two “L” planks

)Note:

Make sure that the package contains the above items. If any of the

listed items are damaged or missing, please contact with your

distributor.

CONTENTS

Chapter 1 Introduction of the Product ...........................................1

1.1Overview of the product ............................................................... 1

1.2Features.......................................................................................1

1.3IEEE 802.1p QoS.........................................................................2

Chapter 2 Installation.......................................................................3

2.1Mounting the Switch on a Desk....................................................3

2.2Mounting the Switch in a Rack.....................................................3

2.3Power on......................................................................................4

Chapter 3 Identifying External Components..................................4

3.1Front Panel................................................................................... 4

3.2Rear Panel...................................................................................5

Appendix A: Specifications.............................................................6

Appendix B: Troubleshooting.........................................................7

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Chapter 1 Introduction of the Product

This chapter describes the features of the model of FSW-1650/FSW-2450

16/24- port 10/100 Rackmount Switch. FSW-1650 and FSW-2450 just

differ in the number of LED indicators and ports, all figures in this guide

are of FSW-2450.

1.1 Overview of the product

FSW-1650/FSW-2450 6/24-port 10/100 Rackmount Switch provides

16/24 10/100Mbps Auto-Negotiation RJ45 ports. Each port of the FSW-

1650/FSW-2450 supports auto MDI/MDI-X function, eliminating the need

for crossover cables or Uplink ports. The Switch is Plug- and-Play and

any port can be simply plugged into a server, a hub or a switch, using

straight cable or crossover cable.

The LevelOne FSW-1650/FSW-2450 16/24-port 10/100 Rackmount

switch provides you with a low-cost, easy-to-use, high-performance,

seamless and standard upgrade to improve your old network to a

100Mbps network. It will boost your network performance up to full duplex

data transfer.

1.2 Features

¾Complies with IEEE802.3, IEEE802.3u standards

¾Support IEEE 802.1p QoS

¾16/24 10/100M Auto-NegotiationRJ45portssupporting Auto-

MDI/MDIX

¾Supports IEEE802.3X flow control for full-duplex mode and

backpressure for half-duplex mode

¾LED indicators for monitoring power, link, activity, speed (FSW-2450)

¾Standard 19” rack-mountable steel case

¾Internal power supply

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

1.3 IEEE 802.1p QoS

The FSW-1650/2450 16/24-Port 10/100M switch supports 802.1p priority

queuing Quality of Service, which is an implementation of the IEEE

802.1p standard. With 802.1p QoS function, you can reserve

bandwidth for important functions that require a large bandwidth or have a

high priority, such as VoIP (voice-over Internet Protocol), web browsing

applications or video conferencing. The switch has separate hardware

queues on every physical port which packets from various applications

are mapped to and assigned a priority to. The illustration below shows

how 802.1p priority queuing is implemented on the switch.

The switch has two priority queues labeled 0 and 1. The untagged

packets and the eight IEEE 802.1p priority levels defined by the standard

are mapped to the two class queues used on the switch. Class 1 has

the higher priority of the two priority queues on the switch. The untagged

packets and eight priority tags, specified in IEEE 802.1p are mapped to

the switch’s priority as follows:

The untagged packets and priority 0,1,2 and 3 are assigned to the

switch’s class 0 queue.

Priority 4,5,6, and 7 are assigned to the switch’s Class 1 queue.

The Switch uses WRR( Weighted Robin Round) for scheduling. WRR

queue-scheduling algorithm schedules all the queues in turn and every

queue can be assured of a certain service time. The default weight

value of Class 0 queue and Class 1 queue is 1 to 8.

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Chapter 2 Installation

2.1 Mounting the Switch on a Desk

Before placing the Switch on a desk, attach four rubber feet to the flutes

on the Switch bottom, then lay the Switch on the desktop,

where it is able to withstand 5kg of weight.

)Note:

Make sure there is a grounded AC outlet within 1.5 meters, and

working well. Make sure there is free space for radiating heat

and air.

Make sure not to place anything to heavy on top of the switch.

2.2 Mounting the Switch in a Rack

The dimension of FSW-1650 / FSW-2450 is designed according to the

standard 19” rack-mountable steel case of Electronic Industries

Association.

Powers off all the equipment connected to the Switch before mounting it

in the rack, then rivet the two “L” brackets onto each side of the Switch,

and fasten it with screws in the rack.

Figure 2-1 Rivet the ‘L’brackets onto the Switch

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Figure 2-2 Fasten the Switch in the rack

2.3 Power on

The FSW-1650/FSW-2450 16/24-port 10/100 Rackmount switch is

by power cord. Powering on the Switch, it will be automatically initialized

and the LED indicators should respond as follows:

1) All of the LED indicators will flash momentarily for one second,

which represent a resetting of the system.

2) The Power LED indicator will light up.

Chapter 3 Identifying External Components

This Chapter describes the front panel, rear panel and LED indicators of

the Switch.

3.1 Front Panel

The front panel of FSW-2450 consists of switch model, switch LED

indicators, and 24 10/100Mbps RJ-45 ports.

FSW-1650/FSW-2450 10/100 Rackmount Switch User's Guid

Figure 3-1 FSW-2450 Switch Front Panel sketch

3.2 Rear Panel

The rear panel of FSW-2450 only features an electrical outlet, which is an

AC electrical outlet. Connect the female of the power cord head here, and

the male head to the AC power.

Figure 3-2 FSW-2450 Switch Rear Panel sketch

LED indicators

The LED indicators include Power, Link/Act LED indicators, which are

used for monitoring and pre-troubleshooting of the Switch. The following

section shows the LED indicators of the Switch along with an explanation

of each indicator.

Figure 3-3 FSW-2450 Switch LEDs sketch

¾Power LED: This indicator will light solid red when the Switch

powers up. If the LED is not lit, please check the power supply and

connection.

¾LINK/ACT LED: The LED indicates Link/Active status. The

corresponding LED indicator will light solid green when connected to

a network device. It flashes green when data is being transmitted or

received on the working connection.

¾100Mbps: The corresponding gigabit port LED indicator will light

solid green when it's working on 100Mbps speed, not lit when

working on 10Mbps speed.

Other manuals for FSW-1650

This manual suits for next models

Table of contents

Other LevelOne Network Router manuals

LevelOne

LevelOne FSW-0811 User manual

LevelOne

LevelOne WBR-3470 User manual

LevelOne

LevelOne PLI-2020 User manual

LevelOne

LevelOne FHU-0803TXD User manual

LevelOne

LevelOne FNS-7000A User manual

LevelOne

LevelOne NetCon FBR-4000 User manual

LevelOne

LevelOne WBR-6013 User manual

LevelOne

LevelOne IFE-0501 User manual

LevelOne

LevelOne PLI-2030 User manual

LevelOne

LevelOne FNS-7000B User manual

LevelOne

LevelOne FEU-2410 User manual

LevelOne

LevelOne FSW-2441TX User manual

LevelOne

LevelOne FBR-1403TX User manual

LevelOne

LevelOne IES-0810 User manual

LevelOne

LevelOne FSW-0809 User manual

LevelOne

LevelOne HomePlug Pro PLI-3210 User manual

LevelOne

LevelOne WBR-6006 User manual

LevelOne

LevelOne NetCon WBR-3408 User manual

LevelOne

LevelOne WBR-3601 User manual

LevelOne

LevelOne WBR-6603 User manual

LevelOne

LevelOne FRT-2101TX User manual

LevelOne

LevelOne WBR-3402TX User manual

LevelOne

LevelOne WBR-6003 User manual

LevelOne

LevelOne WBR-6802 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview