Ledj LEDJ225 User manual

www.prolight.co.uk

OUTDOOR TRI PAR

USER MANUAL

Order code: LEDJ225

Outdoor Tri Par Safety

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

INPUT VOLTAGE OF 110~240V

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Outdoor Tri Par Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Do not expose to ammable sources or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the LEDJ carton the following items:

1, Outdoor Tri Par 2, Instruction manual 3, Power cable

Technical Specications:

DMX channels: 6

12 x Ultra Bright 3W Tri-colour LEDs

IP rated power in/out sockets

IP rated DMX in/out sockets

400Hz icker free

IP rating: IP-65

Beam angle: 25 degrees

Power supply: 110~240V - 50~60Hz

Power consumption: 68W

Dimensions: 260 x 240 x 209mm

Weight: 3.7Kgs

Operating modes: 1, Static colour

2, Colour change

3, Colour fade

4, Master/slave

5, DMX

Overview:

1, DMX input

2, DMX output

3, LED display

4, Power input

5, Power output

6, Mode selection button

7, Enter button

8, Function up button

9, Function down button

Outdoor Tri Par Technical specications

Operation:

There are 5 different operation modes to choose from:

1) Static colour mode 2) Colour change mode 3) Colour fade mode

4) Master/slave 5) DMX mode

1, Static colour mode

Mode button - Press the “MODE” button under the LED display, to show “C000”, then press the

“ENTER” button to choose one of the static colours using the “UP” and “DOWN” buttons.

The “C1” represents Red, “C2” = Green, “C3” = Blue and “CF” = strobe.

The two digits after it are the brightness 00 to 99 or in “CF” they are the strobe speed.

Examples: If you set C1, C2 and C3 to zero, the Outdoor Tri Par will have no LEDs on (blackout).

If you set C1 to 99 and C2 and C3 to zero, the Tri Par will be 100% Red.

NOTE: For static selection of Red, Green, and Blue, ensure that the unwanted

colours are set to “00”.

2, Colour change mode

Mode button - Press the “MODE’ button until the LED display shows “J000”, then press the

“ENTER” button to choose one of the colour changing modes using the “UP” and “DOWN” buttons.

The colour change programmes are as follows:

1, “J300” = RGB, 2, “J700” = 7 colour, 3, “JF00” = Strobe,

Now press the “ENTER” button again and you can then select the colour change speed using the

“UP” and “DOWN” buttons. The speed settings are from 00-99 (00 = slow, 99 = fast)

3, Colour fade mode

Mode button - Press the MODE button until the LED display shows “F000”, then press the

“ENTER” button to choose one of the colour fading modes using the “UP” and “DOWN” buttons.

The colour fade programmes are as follows:

1, “F300” = RGB, 2, “F700” = 7 colour, 3, “FF00” = Strobe,

Now press the “ENTER” button again and you can then select the colour fade speed using the

“UP” and “DOWN” buttons. The speed settings are from 00-99 (00 = slow, 99 = fast)

4. Master/slave mode

Link the units together using a 3-pin DMX cable, then press the “MODE” button to select one of the

above modes. On the Slave units press the mode button until the LED display shows “SLAV”. The

Slave units will then follow in sequence with the Master unit.

Note: To conrm the setting in any of the above mode always press the “ENTER” button a

nal time so that the LED display stops ashing.

Outdoor Tri Par Operation

5, DMX addressing mode

To access the DMX address mode, press the “MODE” button until the LED display shows “A001”,

and use the “UP and “DOWN” buttons to select the desired DMX address and press the

“ENTER” button to conrm the setting. Then follow the DMX channel assignment and function

table below.

6 Channel DMX chart

Outdoor Tri Par Operation

Channel

Value

000-255

0-4

5-84

85-169

170-255

0-255

Function

Master dimmer

Red (0 - 100%)

Green (0 - 100%)

Blue (0-100%)

No function

Colour macro

Colour jump

Colour fade

Strobe

Outdoor Tri Par DMX Set up

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Outdoor Tri Par can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a 3-pin XLR connector for data input/

output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Further exterior extension

DMX cables can be purchased

from all LEDJ dealers.

Please quote:

LEDJ140 - 1M

LEDJ142 - 2M

LEDJ143 - 5M

LEDJ144 - 10M

DMX cables can be purchased

from all LEDJ dealers.

Please quote:

LEDJ91 - 1M

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Outdoor Tri Par DMX Set up

Table of contents

Other Ledj Lighting Equipment manuals

Ledj

Ledj Stage Par CZ200 Dual White User manual

Ledj

Ledj ECO LED Par 56 User manual

Ledj

Ledj STAR15 User manual

Ledj

Ledj PERFORMER 54 RGBW LEDJ250 User manual

Ledj

Ledj LEDJ251 User manual

Ledj

Ledj Omni Tri-9 User manual

Ledj

Ledj LEDJ24 User manual

Ledj

Ledj Spectra QX40 Pixel MKII Exterior Fixture User manual

Ledj

Ledj LEDJ472 User manual

Ledj

Ledj Spectra Par LEDJ88 User manual

Ledj

Ledj minibar TC User manual

Ledj

Ledj Artisan 1000 User manual

Ledj

Ledj Stage Par CZ 120 RGBA User manual

Ledj

Ledj Libretto Mini Bi-CCT Profile User manual

Ledj

Ledj Event Spot Bar RGBW User manual

Ledj

Ledj LEDJ02 User manual

Ledj

Ledj Aspect XL User manual

Ledj

Ledj Slimline 7HEX6 Series User manual

Ledj

Ledj Mini Pix 4 Batten User manual

Ledj

Ledj Spectra Batten LEDJ76 User manual

Ledj

Ledj FLEX30 User manual

Ledj

Ledj Stage Par CZ200 3200K User manual

Ledj

Ledj LEDJ252C User manual

Ledj

Ledj LED RGB 252 User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions