Ledj BlockBuster 6 User manual
www.prolight.co.uk
BlockBuster 6
(Order code: LEDJ73)
LEDJ BlockBuster 6 Safety
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
LEDJ BlockBuster 6 Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
LEDJ BlockBuster 6 Operations
Operation
When the power is turned on, the LCD display will be as below:
Press the “MODE” button to activate the main menu: Built-in programme, Auto run, DMX mode,
Slave mode and Sound mode.
• Built-in programme: Runs one of the 14 built-in programmes
• Auto run: Runs the built-in programmes one after another in a continuous loop
• DMX mode: Control by external DMX controller
• Slave mode: The unit in this mode can be linked to run with another unit set to Master
mode.
• Sound mode: Programmes are activated to the sound by the built-in microphone
1) A programme is a sequence of different steps, with the BlockBuster 6 you can select up to 14
different programmes. Press the “set up” and the UP/DOWN buttons to select between pro
grammes(00-14) and select the desired programme value (step time and ash).
For example: Press the “set up” button to move the cursor to select 02 and then desired Sp
(step time) or Fs (ash speed).
• SP: Step time value from 001 - 100 • FS: Flash speed from value 00 - 100
2) Auto run
Runs 14 programmes in a continuous loop, the frequency means the speed of the run
times can be set via the UP and DOWN buttons.
3) DMX mode:
You can control the units individually using your DMX controller
a) The control board allows you to assign the DMX address which is dened as the rst channel
from which the BlockBuster 6 will respond from the controller. For address setting, press the
“set up” button until the display shows as follows:
WELCOME
TO USE
FLOOD LED
324 RGB
ONE SECOND
02.SLOW D
S001 F012
AUTO RUN
FQN:00
DMX MODE
ADDR:001
LEDJ BlockBuster 6 Operations
b) DMX-protocol
The control board allows you to set 5, 8, 11 or 20 DMX channels for different applications.
Press the “set up” button until the display is as follows:
Set the desired channels (5, 8, 11 or 20) Via the UP and DOWN buttons
1, Set for 20 Channels:
The dimmer occupies the rst channel when DMX value is smaller than 251, the ash occupies
the second channel, each spot occupies 3 channels, six spots occupy 18 channels and the full
unit occupies 20 channels.
2, Set for 11 channels:
The dimmer occupies the rst channel when the DMX value is smaller than 251, the ash
occupies the second channel, every 2 spots occupy 3 channels, six spots occupy 9 channels
and the full unit occupies 11 channels.
3, Set for 8 channels:
The dimmer occupies the rst channel when the DMX value is smaller than 251, the ash
occupies the second channel, every 3 spots occupy 3 channels, six spots occupy 6 channels
and the full unit occupies 8 channels.
4, Set set 5 channels:
The dimmer occupies the rst channel when the DMX value is smaller than 251, the ash
occupies the second channel, six spots occupy the same 3 channels, and the full unit
occupies 5 channels.
5, During any of the four above DMX modes the rst DMX channel value must be between 251
and 255.
DMX MODE
CH NO:20
LEDJ BlockBuster 6 DMX-Protocol
CH1 CH2 CH3 CH4 CH5
251 - 255
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
0-10
11-21
22-32
33-43
44-54
55-65
66-76
77-87
88-98
99-109
110-120
121-131
132-142
143-153
154-164
165-175
176-186
187-197
198-208
209-219
220-230
231-255
BLACKOUT
RED
YELLOW
GREEN
CYAN
BLUE
PURPLE
WHITE
SLOW DREAM
FAST DREAM
COLOUR FADE
COLOUR CHANGE
FLOW 1
FLOW 2
FLOW 3
FLOW 4
DOUBLE FLOW 1
DOUBLE FLOW 2
MULTI COLOUR
2 COLOUR FLOW 1
2 COLOUR FLOW 2
SOUND ACTIVE
NOT USED
FLASH
0-225
(0-28HZ)
FLASH
0-225
(0-28HZ)
SPEED
0-255
SPEED
0-255
FLASH
0-225
(0-28HZ)
COLOUR
0-255
SENSITIVITY
0-255
(32 grade)
MODE DMX
VALUE
4, Slave mode:
Press the MODE button repeatedly until the display shows Slave Mode. The unit will now
follow another that is set to Master Mode
5, Sound mode:
Adjust the audio level input by pressing the UP and DOWN buttons. The range is 0-31
SOUND
SENS:31
DMX-Protocol
NOT USED
NOT USED
NOT USEDNOT USED
LEDJ BlockBuster 6 Specications
Specications:
• 324 high intensity LED’s
• Red 108, Green 108, Blue 108 (total 324)
• LED beam angle: 30 degree’s
• Dimensions: 800 x 100 x 75mm
• Weight: 5.5kg
• Power in: 240v ~ 50Hz
• Power consumption: 35 watts
Table of contents
Other Ledj Lighting Equipment manuals
Ledj
Ledj Archi BAR 48 User manual
Ledj
Ledj LEDJ377 User manual
Ledj
Ledj STRATOS SPOT User manual
Ledj
Ledj Mini Pix 9 Panel User manual
Ledj
Ledj Rapid QB1 RGBW Battery Uplighter User manual
Ledj
Ledj Pixel Bar LEDJ73A User manual
Ledj
Ledj STAGE BAR 16 User manual
Ledj
Ledj LEDJ P85 User manual
Ledj
Ledj Aspect User manual
Ledj
Ledj minibar TC User manual
Ledj
Ledj HBR 1D User manual
Ledj
Ledj Aspect XL User manual
Ledj
Ledj ALU ZOOM PAR 64 User manual
Ledj
Ledj SPECTRA PAR 7T3 User manual
Ledj
Ledj Spectra Flood 18HEX10 User manual
Ledj
Ledj STAGE CLOUR QUAD User manual
Ledj
Ledj Slimline 1T100 User manual
Ledj
Ledj STAGE PAR 64 User manual
Ledj
Ledj Slimline 3HEX12 Series User manual
Ledj
Ledj LEDJ352A User manual
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
