Ledj LEDJ186 User manual

Order code: LEDJ186

UV 50W COB Flood

1 x 50W UV COB LED

User Manual

Optional

IR remote

Order ref:

LEDJ90E

www.prolight.co.uk UV 50W COB Flood User Manual

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.

• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.

• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary

fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.

• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand

thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.

Donotendangeryourownsafetyandthesafetyofothers!

Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.

• Neverletthepowercablecomeintocontactwithother

cables.Handlethepowercableandallmainsvoltage

connectionswithparticularcaution!

• Neverremovewarningorinformativelabelsfromtheunit.

• Donotopentheequipmentanddonotmodifytheunit.

• Donotconnectthisequipmenttoadimmerpack.

• Donotswitchtheequipmentonandoffinshortintervals,

asthiswillreducethesystem’slife.

• Onlyusetheequipmentindoors.

• Donotexposetoammablesources,liquidsorgases.

• Alwaysdisconnectthepowerfromthemainswhen

equipmentisnotinuseorbeforecleaning!Onlyhandle

thepower-cablebytheplug.Neverpullouttheplugby

pullingthepower-cable.

• Makesurethattheavailablevoltageisbetween

110~240V,50/60Hz.

• Makesurethatthepowercableisnevercrimpedor

damaged.Checktheequipmentandthepowercable

periodically.

• Iftheequipmentisdroppedordamaged,disconnectthe

mainspowersupplyimmediatelyandhaveaqualied

engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic

temperatureuctuation(e.g.aftertransportation),

donotconnectpowerorswitchitonimmediately.

Thearisingcondensationmightdamagetheequipment.

Leavetheequipmentswitchedoffuntilithasreached

roomtemperature.

• Ifyourproductfailstofunctioncorrectly,stopuse

immediately.Packtheunitsecurely(preferablyinthe

originalpackingmaterial),andreturnittoyourProLight

dealerforservice.

• Onlyusefusesofsametypeandrating.

• Repairs,servicingandpowerconnectionmustonlybe

carriedoutbyaqualiedtechnician.THISUNITCONTAINS

NOUSERSERVICEABLEPARTS.

• WARRANTY:Oneyearfromdateofpurchase.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

www.prolight.co.uk UV 50W COB Flood User Manual

Product overview & technical specications

Thispowerful50WUVFloodwillllavarietyofvenueswithanoutstandingUVglow.Theseunitshavearugged,

metalhousingandmeasureonly130mmindepthforeasytransportationandinstallation.

Theyarealsoconvectioncooledforsilentoperationandfeaturea85°beamangle.The4pushbuttonLED

menuorincludedIRremotealloweasyaccesstothefunctionsincludingDMX,master/slave,soundactive

andstandalonemodes.

•1x50WUVCOBLED

•Beamangle:85°

•1.1kHzrefreshrate

•DMXchannels:1or2selectable

•Standalone,soundactiveandmaster/slavemodes

•0-100%dimmingwithvariablestrobe

•Bracketallowsformultipleriggingand

oorstandingapplications

•Rearcontrolpanelandrubberfeetallowthe

paneltositatontheoorforuplighting

•4pushbuttonmenuwithLEDdisplay

•SideentryXLRandpowerconnections

•IECpowerin/outsockets

•3-pinXLRin/outsockets

•Fancooled

•SuppliedwithIRremote(LEDJ90E)

UV Spectra Batten

Specications UV 50W COB Flood

Powerconsumption 56W

Powersupply 110~240V,50/60Hz

Fuse F1A250V

Dimensions 284x248x130mm

Weight 2.8kg

Ordercode LEDJ186

248mm 130mm

284mm

www.prolight.co.uk UV 50W COB Flood User Manual

01-Bracket

02-Brackettighteningknobs

03-Earthpoint

04-LEDdisplay

05-Functionbuttons

06-DMXinputsocket

07-DMXoutputsocket

08-IECpowerinsocket

09-IECpoweroutsocket

10-FuseF1A250V

0810 0903 07 06

ENTER DOWN

MODE

POWER IN POWER OUT DMX OUT DMX IN

www.prolight.co.uk

50W COB FLOOD

PUSH

Technical specications

Inthebox:1 x xture,

1 x IR remote,

1 x power cable &

1 x user manual

www.prolight.co.uk UV 50W COB Flood User Manual

Operating instructions

DMX channel mode:

ToaccesstheDMXchannelmode,pressthe“MODE”buttonontherearoftheunittoshowA001

ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe

desiredDMXaddress.Nowpressthe“ENTER”buttontochooseoneofthe1or2DMXchannelmodes

usingthe“UP”and“DOWN”buttons,andpressthe“ENTER”usethe“UP”and“DOWN”buttonstoset

whattheunitshoulddoifitlosesDMXsignal.

bLC-TheunitwillblackoutifDMXsignalislost.

Soun-TheunitwillgointosoundactivemodeifDMXsignalislost.

HoLd-TheunitwillholdthelastDMXcommandifDMXsignalislost.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

Static mode:

Toaccessstaticmodepress“ENTER”untilthedisplayshowsC-00ontheLEDdisplay.

Toadjustthebrightnessusethe“UP”and“DOWN”buttonstoselectbetweenC-00~C-99.

Pressthe“ENTER”buttontoconrmthesetting.Nowusethe“UP”and“DOWN”buttonstoadjustthe

ashspeedbyselectingbetweenF-00~F-99.Pressthe“ENTER”buttontoconrmthesetting.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

Slave mode:

Pressthe“MODE”buttonontherearoftheunittoshowSLAUontheLEDdisplayandpressthe

“ENTER”buttontoconrmthesetting.Theunitwillnowruninsequencewiththemasterunit.

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.

Sound active mode:

Toaccessthesoundactivemode,pressthe“MODE”buttonontherearoftheunittoshowSU00

ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe

soundsensitivitylevelfromSU.00~SU.99andpressthe“ENTER”buttontoconrmthesetting.

Value: 00 - 99 (00 = low, 99 = high)

Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

Channel Value Function

1000-255 Masterdimmer(0-100%)

Channel Value Function

1000-255 Masterdimmer(0-100%)

2000-255 Flashspeed(slowtofast)

1 channel mode: 2 channel mode:

Staticmode C-00~C-99Brightness(0-100%)

F-00~F-99Flashspeed(slow-fast)

Slavemode SLAV

Soundactivemode SU00~SU99

Menusystem

DMXmode 1CH,2CH

Addresssetting A001~A512

IRfunction Iron -IROn

IroF -IROff

www.prolight.co.uk UV 50W COB Flood User Manual

Operating instructions & DMX setup

Included IR remote functions:

Button functions:

DMX address examples:

TosettheDMXaddress;

• Pressthe“S”button,theLEDxturewillilluminate

infull,youcannowstarttosettheDMXaddress

• Selecttherequired3digitDMXaddress

(eg001or136or275)theunitwillthenash

toconrmtheaddresshasbeenset

• Nowpressthe“DMXMODE”buttontosavethenewaddressintothememory

Important notes:

• SettheDMXaddressoneachxturebeforepluggingintotheDMXcontroller

• TheIRremotecannotbeusedwhenthexture(s)arebeingcontrolledwithaDMXcontroller

• ThemaximumIRtransmitterdistanceis10m-PleasemakesurethatyouhavetheIRremote

aimeddirectlyatthefrontpanelofeachxturetobeprogrammed

• Ifyoudonotpressthe“DMXMODE”buttonafteryouhavechangedtheDMXaddresswhenyou

powerdownthextureitwilllosetheaddressyouhaveset

Setting the DMX address:

TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”

from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel

indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas

addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105

and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe

chainstartsat107.

01-Blackout

02-TosetthebrightnessoftheLEDeither

select20%,50%or100%oralternatively

youcanusethe‘+’and‘-’buttons

03-Flashoff

04-TosettheashspeedoftheLEDeither

select20%,50%or100%oralternatively

youcanusethe‘+’and‘-’buttons

05-SetstheLEDxtureintoDMXmode

06-SetstheLEDxtureintosoundactivemode

07-SetstheLEDxtureintoslavemode

08-SetstheDMXaddressfortheLEDxture

1 2 3

4 5 6 0

7 8 9

D SL S

OFF 20% 50% 100%

STROBE

OFF 20% 50% 100%

DIMMING

SLAVE SET ADDRSOUND ACTIVEDMX MODE

05 08

Included

IR remote

Order code:

LEDJ90E

www.prolight.co.uk UV 50W COB Flood User Manual

DMX 512:

DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent

xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.

DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”

XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).

DMX linking:

DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether

andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.

ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest

cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe

DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein

aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda

DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,

nomatterwhereitislocatedintheDMXchain.

DATA cable (DMX cable) requirements (for DMX operation):

ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.

YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,

seeimagebelow.

Also remember that DMX cable must be daisy chained and cannot be split.

Notice:

Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables

shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs

outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.

DMX setup

FurtherDMXcablescanbe

purchasedfromallgoodsound

andlightingsuppliersor

ProLightConceptsdealers.

Pleasequote:

CABL10 – 2m

CABL11 – 5m

CABL12 – 10m

www.prolight.co.uk UV 50W COB Flood User Manual

Special note:

Line termination:

Whenlongerrunsofcableareused,

youmayneedtouseaterminatoron

thelastunittoavoiderraticbehaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures

maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa

3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

Terminationreducessignaltransmission

problemsandinterferance.itisalways

advisabletoconnectaDMXterminal,

(resistance120Ohm1/4W)betweenpin2

(DMX-)andpin3(DMX+)ofthelastxture.

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (socket)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup & WEEE notice

Correct Disposal of this Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries

with separate collection systems)

Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof

withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe

environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother

typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.

Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir

localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally

saferecycling.

Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe

purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

This manual suits for next models

Table of contents

Other Ledj Light Fixture manuals

Ledj

Ledj spectra flood 18T3 User manual

Ledj

Ledj spectra flood 18T3 User manual

Ledj

Ledj Rapid QB1 User manual

Ledj

Ledj Spectra Par 12T3 User manual

Ledj

Ledj Spectra Batten User manual

Ledj

Ledj Spectra Batten User manual

Ledj

Ledj Spectra Par 12HEX10 User manual

Popular Light Fixture manuals by other brands

Emos

Emos CLASSIC ZY1431T manual

Westinghouse

Westinghouse Outdoor Lighting Fixture owner's manual

Hedler

Hedler C 12 silent Operation manual

Blizzard Lighting

Blizzard Lighting Puck: CSI manual 

Energetic Lighting

Energetic Lighting ELYSL-5004 Series installation instructions

Lightmaxx

Lightmaxx Shaft 5R user manual

Triarch

Triarch 31083 Assembly instructions

Philips

Philips 32614 Series user manual

IKEA

IKEA TIVED Assembly instructions

Lightolier

Lightolier LP200 specification

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH user manual

Martin

Martin MAC 250 Krypton user manual

Cooper Lighting

Cooper Lighting Halo L3232E Specification sheet

Stageline

Stageline ODW-2410RGBW instruction manual

Light Sky

Light Sky Tornado Series user manual

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U specification

Lightolier

Lightolier Lytespan 83ED17S specification

Lightolier

Lightolier Calculite CS8226 specification