Larson Electronics EPL-MBC-1MLED-2023 Manual

EPL-MBC-1MLED-2023

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

EPL-MBC-1MLED-2023 Instruction Guide

150 Watt Magnetic Explosion Proof LED Light

Thank you for your purchase of the Larson Electronics EPL-MBC-1MLED-2023 Portable Explosion Proof LED

Light. Please follow the steps below in order to operate and maintain this product.

IMPORTANT

READ CAREFULLY BEFORE OPERATING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE EPL-MBC-1MLED-2023 MUST BE OPERATED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

FOR PERSONAL SAFETY, ALWAYS CONFIRM THE RATING OF ANY KNOWN HAZARDOUS OR POTENTIALLY

HAZARDOUS LOCATION WHERE THE LIGHT IS TO BE USED.

WARNING: TO PREVENT IGNITION OF A HAZARDOUS ATMOSPHERE, THE SUPPLY CIRCUIT SHOULD BE

DISCONNECTED WHEN INSTALLING OR PERFORMING ANY MAINTENANCE ON THIS UNIT.

WARNING: WHEN INSTALLING THIS LIGHT IN HAZARDOUS LOCATIONS, CHECK THE OPERATING

TEMPERATURE LIMITS PRIOR TO INSTALLATION TO BE SURE IT CONFIRMS TO THE ENVIRONMENTAL

TEMPERATURE RESTRICTIONS AND NEC CLASSIFICATIONS. CHECK THE FIXTURE’S METAL NAMEPLATE FOR

TEMPERATURE (T) RATINGS.

WARNING: DO NOT SCRATCH OR CHIP THE FRONT LENS. TURN THE POWER OFF BEFORE STARTING

INSTALLATION OR REPAIR.

WARNING: OPERATE THIS FIXTURE ONLY AT THE VOLTAGE OF YOUR SPECIFIC SUPPLY CIRCUIT. FAILURE

TO DO SO WILL RESULT IN DAMAGE TO THE FIXTURE.

WARNING: SUBSTITUTE COMPONENTS MAY IMPAIR EXPLOSION PROOF SAFETY.

•PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE USE. ELECTROMAGNETIC

FIELDS IN CLOSE PROXIMITY TO HEART PACEMAKER COULD CAUSE PACEMAKER INTERFERENCE OR

PACEMAKER FAILURE.

•KEEP FINGERS AWAY FROM MAGNET(S) WHEN MOUNTING AS INJURY COULD OCCUR.

OPERATING

Before operation, confirm that the power source will provide the correct voltage indicated on the product

nameplate. Ensure the receptacle will accept the cord cap attached to the light.

Check product nameplate for Ratings and Approvals.

Affix light in the desired location and run its power cord to a compatible power source.

Mount light to a metal surface that can structurally support the load. Six 200lb. grip

magnets hold the fixture in any position. Ensure all safety requirements are followed for

the hazardous area.

Avoid excess tension between cord and light to reduce stress on the magnets. Mark

area as needed to avoid potential trip hazards or cable snags causing the light to dismount.

The light head can be adjusted by loosening the hand screws on each side. Once loose,

position the light head in the desired angle and tighten the hand screws to hold the light

in place. Use caution while adjusting as to not pinch your fingers between light and

mount.

This light is “instant-on” once plugged in to a live circuit. Do not face the light while energizing to avoid direct

eye exposure.

AVOID DIRECT EYE EXPOSURE Do not look at the face of or directly into the light when plugging in or when

illuminated.

HAND SCREW

EPL-MBC-1MLED-2023

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MAINTENANCE

It is recommended that you implement a standard monthly or more frequent preventive maintenance schedule.

Safety requires a thorough visual examination of the unit for physical damage that might cause a spark or

result in the ignition of hazardous atmospheres.

Maintenance includes a careful examination to ensure at least:

A. The Light Body is not cracked, broken or breeched.

B. The Lens is not cracked or chipped.

C. The Cable is not frayed and is gripping tightly in all points of cable contact.

D. The Cable Jacket is completely intact and that no internal conductors or conductor insulation

is exposed.

E. The Connection Box is not cracked, broken or breeched.

F. The Cord Plug is not cracked or damaged and the Ground Post is intact.

G. The magnets are fully in-tact with no visible cracks or damage.

For your safety and to maximize the life of the light, avoid rough usage such as:

H. Pulling the Light by the Cable, which could weaken or damage the cable.

I. Impacting the lens with hard, sharp or heavy objects, which could cause the lens to scratch,

chip, crack, or shatter.

J. Disconnecting the Cord Plug from the receptacle by pulling on the Cable.

Keeping the light clean and free of material splatter, overspray, and debris during usage will ensure the

maximum life and luminosity of the light.

TROUBLESHOOTING

Refer to the guide below or contact the manufacturer if the fixture does not function properly.

Is the correct line voltage being supplied to the fixture?

Is the fixture properly grounded?

Make sure installed power switch is functioning properly (if applicable).

These instructions may not cover all details or variations of this product for your equipment or installation

requirements. Should further information not covered by these instructions be required, please contact Larson

Electronics at 1-800-369-6671 for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

Table of contents

Other Larson Electronics Light Fixture manuals

Larson Electronics

Larson Electronics GVP-48-2L-LED-125VDC User manual

Larson Electronics

Larson Electronics GAU-WP-500LTL-LED-WG-DNMS User manual

Larson Electronics

Larson Electronics GVP-EMG-48-2L-LED User manual

Larson Electronics

Larson Electronics EPLC-48-432 User manual

Larson Electronics

Larson Electronics EPLC2-BS-70LED-100 Manual

Larson Electronics

Larson Electronics EPL-PM-1X30LED-120XLV-100 Manual

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT User manual

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-ASM-JB2-40C-BCE User manual

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-4L User manual

Larson Electronics

Larson Electronics ATEX-EPL-TL-3X10W-C User manual

Larson Electronics

Larson Electronics EPL-PM-1X30LED-100 Manual

Larson Electronics

Larson Electronics SPLT-1.59K-800A-30-4X100W-LED-MS User manual

Larson Electronics

Larson Electronics LEDWP-600E-E2E-10C User manual

Larson Electronics

Larson Electronics EPL-HB-5K-LED User manual

Larson Electronics

Larson Electronics EPL-EMG-HB-50LED-RT-WLM User manual

Larson Electronics

Larson Electronics EPL-AMB-150LED-250 User manual

Larson Electronics

Larson Electronics GAU-HB-12L-LED-WP-WCM User manual

Larson Electronics

Larson Electronics EPL-PT-150LED-RT-100-EPP User manual

Larson Electronics

Larson Electronics EPLC2-AMB-70LED-50 Manual

Larson Electronics

Larson Electronics EPL-16BS-1X150LED-X24I-C1D1-200 Manual

Larson Electronics

Larson Electronics HAL-16BS-1X185LED-CPR-100 Manual

Larson Electronics

Larson Electronics EPLC2-WPLED-100W-RT User manual

Larson Electronics

Larson Electronics GVP-48-2L-LED-D-LV User manual

Larson Electronics

Larson Electronics EPLC2-LB-45LED-RT-WLM User manual

Popular Light Fixture manuals by other brands

Emos

Emos CLASSIC ZY1431T manual

Westinghouse

Westinghouse Outdoor Lighting Fixture owner's manual

Hedler

Hedler C 12 silent Operation manual

Blizzard Lighting

Blizzard Lighting Puck: CSI manual 

Energetic Lighting

Energetic Lighting ELYSL-5004 Series installation instructions

Lightmaxx

Lightmaxx Shaft 5R user manual

Triarch

Triarch 31083 Assembly instructions

Philips

Philips 32614 Series user manual

IKEA

IKEA TIVED Assembly instructions

Lightolier

Lightolier LP200 specification

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH user manual

Martin

Martin MAC 250 Krypton user manual

Cooper Lighting

Cooper Lighting Halo L3232E Specification sheet

Stageline

Stageline ODW-2410RGBW instruction manual

Light Sky

Light Sky Tornado Series user manual

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U specification

Lightolier

Lightolier Lytespan 83ED17S specification

Lightolier

Lightolier Calculite CS8226 specification