Larson Electronics WAL-QP-4X500-25 User manual

WAL-QP-4X500-25

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 3

Portable Work Area Flood Lights on Quadpod Mount

4x 500w Quartz Lights – 25’ Cord

Instruction Manual

The WAL-QP-4X500-25 Quadpod Mounted Work Area Light produces 35,000 lumens of light capable of

illuminating an area 11,500 square feet in size. This adjustable light tower is designed for portability and

durable operation and ideal for use in demanding industrial and outdoor construction conditions.

WARNING: Read all instructions carefully

SAVE THESE INSTRUCTIONS

CAUTION: RISK OF ELECTRICAL SHOCK

•Do not use with extension cord near water or

where water may accumulate.

•Keep plugs and receptacles dry.

•For use only on GFCI protected circuits.

•Risk of burns, do not operate without lens.

•Lighted lamp is hot. Keep away from

combustibles. Unplug to change bulb. Do not

touch bulb.

WARNING RISK OF FIRE, ELECTRIC SHOCK,

EXPOSURE.

TO EXCESSIVE UV RADIATION OR INJURY TO

PERSONS

•Unit operates on 120V AC 50/60 Hz only

•Unplug and allow cooling before replacing bulb.

•Bulb gets HOT quickly

•Do not touch hot lens guard or enclosure.

•Do not remain in light if skin feels warm.

•Do not look directly at lighted lamp.r

•Keep lamp away from materials that may bum.

•Do not touch the bulb at any time; use a soft

cloth or gloves. Oil from skin may damage bulb.

•Do not operate the lamp with missing or

damaged guard, lamp containment barrier or

UV light filter.

QUADPOD ASSEMBLY

The quadpod assembly consists of 3 parts:

1. Light head

2. Pole w/Legs

3. Wheel base

To assemble quadpod, begin by placing the legs over the wheel base. Tighten bolt to secure the

wheels. The quadpod can now be rolled around on its wheels. Ensure the legs are folded up before

tilting quadpod to maneuver.

WARNING: Use caution before tilting quadpod with a heavy load. For heavy loads, it is

recommended to remove the light head prior to transporting via wheel base! Failure to do so may

cause serious injury or death. Larson Electronics shall not be held liable for injuries caused by

misuse.

1. Place tower in desired location that is flat and able to support the quadpod without falling over.

2. Loosen hand screw and lower legs until firmly stabilizing quadpod.

3. Tighten hand screw to secure legs.

4. With help, place the light head over top pole and tighten hand screw.

Light weight lamps can be attached by tilting quadpod toward the ground with the legs up. Attach light

head to pole, tighten hand screw and tilt back to its vertical position. DO NOT tilt quadpod while

extended to max height. It is recommended to have another person hold the quadpod while tilting

vertically.

WAL-QP-4X500-25

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 3

For heavy weight lamps, use a ladder and extra help for attaching light head to pole.

Double check that all hand screws are tight before continuing use of the light tower.

EXTENDING

1. Loosen hand screw for extending the light head. Once loose, extend light head until desired

height is achieved with at least 1ft - 2ft remaining inside pole for support.

WARNING: DO NOT over extend light head completely allowing extension pole to free from base! If

the light head becomes free, serious injury or death can occur. Larson Electronics shall not be held

liable for injuries caused by misuse.

2. When desired height is achieved, tighten hand screw to secure light head.

LOWERING

1. To lower mast, grasp light head and slowly loosen hand screw. Lower the light head and

tighten hand screw.

WARNING: DO NOT loosen hand screw allowing light head to fall freely. This can damage the unit

and cause serious injury or death. Always grasp light head before lowering. Larson Electronics shall

not be held liable for injuries caused by misuse.

The quadpod mount light tower can be disassembled for storage or transporting. Unplug light from

power source and remove light head following previous steps for attaching.

Once the light head has been removed, loosen hand screw for legs and fold them up. Wheel to

desired location or remove from wheel base for complete disassembly.

THE LENS AND CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, SCRATCHES OR ANY

SEVERE ABRASIONS, AND IF ANY ARE FOUND, THE PARTS MUST BE REPLACED BEFORE

RESUMING USE OF THE LIGHT TOWER.

BULB INSTALLATION AND REPLACEMENT (DO NOT TOUCH BULB WITH BARE HANDS)

1. Turn the light off and unplug from the power source.

2. Allow the fixture to fully cool before proceeding.

3. Always wear gloves or use a clean cloth to handle bulb. The natural oil from skin will leave a residue that

will cause the light to burn out immediately.

4. To remove the lens cover, remove the retaining screw on the back of the lens cover. The lens cover will

then swing open exposing the bulb.

5. To remove the bulb, grip one end of the bulb and gently push towards the other end and pull outward to

release the bulb.

6. Using a clean cloth or wearing gloves to hold the bulb, gently insert one end of the bulb into the receptacle

and press firmly into place. Place the other end of the bulb into the opposite receptacle and gently press

into place. Make sure bulb is seated properly.

7. Close the lens cover and replace the retaining screw.

8. Do not test light without lens cover properly attached.

WAL-QP-4X500-25

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

3of 3

WIRING (see attached wiring diagram)

This unit comes preconfigured with 25 feet

SOOW Cord and 5-15 Straight Blade Plug. Once

deployed, plug cord cap into compatible

receptacle with Voltage: 120 Volts AC, 50/60Hz

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool

down before performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens

will void the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend

routine checks to be made on a yearly basis. Frequency of use and environment should

determine this. It is recommended to follow an Electrical Preventive Maintenance Program

as described in NFPA 70B: Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric

performance. Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use

mild soap or a liquid cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions

or contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if

needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

REPLACEMENT PARTS

The WAL-QP-2X-25 is designed to provide years of reliable performance. Should the need for

replacement parts arise, please see part numbers below and attached drawings in next section.

Some parts may be sourced locally from your nearby hardware store.

Description:

Part Number:

Quadpod assembly:

ALU-TP-W-712

Replacement Bulb Set:

WAL-SB-500Q-KIT

Replacement Lens:

WAL-M-183

The WAL-QP-4X500-25 is designed to provide years of reliable lighting performance. Should the need

for replacement parts arise, please contact Larson Electronics at the contact information below.

WARRANTY

Should further information not covered by these instructions be required, please contact Larson

Electronics at 1-800-369-6671 or sales@larsonelectronics.com for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE WILL

VOID WARRANTY.

Table of contents

Other Larson Electronics Floodlight manuals

Larson Electronics

Larson Electronics EPL-WPLED-150W-RT-140DB User manual

Larson Electronics

Larson Electronics HID-22-SL-3M-GAP User manual

Larson Electronics

Larson Electronics EPL-LED-150W-RT-DIMM User manual

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-JB2 User manual

Larson Electronics

Larson Electronics EPLC2-WPLED-50W-RT User manual

Larson Electronics

Larson Electronics EPL-LED-2X150W-RT User manual

Larson Electronics

Larson Electronics HAL-PRM-150W-LED User manual

Larson Electronics

Larson Electronics GLR-FLK-2 User manual

Larson Electronics

Larson Electronics LEDWP-720 User manual

Larson Electronics

Larson Electronics Golight RadioRay 7901 Manual

Larson Electronics

Larson Electronics LEDWP-LP-450-KNL-DCM User manual

Larson Electronics

Larson Electronics GL-4600-F-M-12I Manual

Larson Electronics

Larson Electronics Golight Stryker ST Series Manual

Larson Electronics

Larson Electronics HAL-TRN Series User manual

Larson Electronics

Larson Electronics LEDEQ-PK-24X2-CPR-SPFL User manual

Larson Electronics

Larson Electronics RCL200-RF User manual

Larson Electronics

Larson Electronics EPL-LED-150W-RT-20-HDBC User manual

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-DIMM User manual

Larson Electronics

Larson Electronics EPL-20W-HID-X12V-25-HR User manual

Larson Electronics

Larson Electronics HAL-LED-174W User manual

Larson Electronics

Larson Electronics LEDWP-LP-450-TRN-DCM User manual

Larson Electronics

Larson Electronics GL-4600 Manual

Larson Electronics

Larson Electronics WAL-SM-MHFL-1000W-50C User manual

Larson Electronics

Larson Electronics WAL-M-3X48LED-120 User manual

Popular Floodlight manuals by other brands

VIZULO

VIZULO Micro Martin Mounting instruction

EuroLite

EuroLite LED IP FL-100 SMD user manual

Cooper Wheelock

Cooper Wheelock XB12 specification

Allen + Roth

Allen + Roth 17624-000 user manual

ADJ

ADJ 4 STAGE PAK User instructions

Cooper Lighting

Cooper Lighting EGL91SW233 Specification sheet

Max

Max 37496 instruction manual

BEGA

BEGA 85 143 Instructions for use

Beamz

Beamz 151.226 user manual

EuroLite

EuroLite LED IP FL-8 user manual

Ledj

Ledj PERFORMER 36 RGB user manual

Perel

Perel ELS3 user manual

Perel

Perel ELS3WD user manual

LumX

LumX LM 36130 instruction manual

Xtricity

Xtricity 4-80053 instructions

Stahl

Stahl 6521/4 Series operating instructions

Ecosense

Ecosense EcoSpec installation manual

Ayrton

Ayrton minipanel FX manual