Lantech IGS-0208GSFP User manual

Lantech

I(P)GS-0208GSFP

8 10/100/1000T + 2 1G SFP (w/8 PoE at/af)

Industrial Unmanaged Switch

User Manual

Aug 2021

Recommendation for Shielded network cables

STP cables have additional shielding material that is used to reduce external interference. The

shield also reduces the emission at any point in the path of the cable. Our recommendation is

to deploy an STP network cable in demanding electrical environments. Examples of

demanding indoor environments are where the network cable is located in parallel with

electrical mains supply cables or where large inductive loads such as motors or contactors are

in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the

power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

Content

Overview............................................................3

Introduction .............................................................. 3

Packing List.............................................................. 3

Safety Precaution.....................................................3

Hardware Description.........................................4

Front Panel...............................................................4

Top View .................................................................. 5

Dimensions .............................................................. 5

Wiring the Power Inputs...........................................6

LED Indicators..........................................................8

RJ-45 Pin Assignments............................................9

Cabling...................................................................11

Mounting Installation........................................15

DIN-Rail Mounting.................................................. 15

Wall-Mount Plate Mounting....................................17

Hardware Installation .......................................18

Installation Steps.................................................... 19

Troubleshooting ...............................................20

Overview

Introduction

Lantech I(P)GS-0208GSFP is a high performance all Gigabit switch

with 8 10/100/1000T + 2x 1G SFP (w/8 PoE 802.3af/at Injectors.)

For latest product specifications, please refer to Lantech official site.

Packing List

1 x Industrial Ethernet Switch

1 x Terminal Block

1 x Quick Installation Guide

Safety Precaution

Attention

If DC voltage is supplied by an external circuit, please use a

protection device on the power supply input.

Hardware Description

In this paragraph, we will introduce the Industrial switch’s dimensions,

port, cabling information, and wiring installation.

Front Panel

The Front Panel of the switch is shown as below.

Front Panel of the Industrial Switch

Top View

The top panel of the Industrial Switch is equipped one terminal block

connector of two DC power inputs.

Top panel of the Industrial Switch Converter

Dimensions

. The dimensions are 74 x 152 x 105 mm (W x H x D). The figure below

gives the dimensions and views of each side of the Industrial Switch.

Wiring the Power Inputs

Voltage of Power Input

IPGS-0208GSFP-12V

12V model:

The power input voltage can

be from 9.5V to 56VDC to

feed power on both the

802.3af and 802.3at

standardized devices.

IPGS-0208GSFP-48V

48V model:

The power input voltage can

be from 45V to 56VDC to feed

power on both 802.3af/at

standardized devices.

IGS-0208GSFP

The power input voltage can

be from 9.5V to 60VDC

Please make sure that the external power supply unit you use

to provide the PoE voltage meet the following criteria: The

power consumption can satisfy the total power request from all

PD devices required.

Please follow the steps below to insert the power wire.

1. Insert the positive and negative wires into the V+ and V- contacts on the

terminal block connector.

2. To tighten the wire-clamp screws for preventing the DC wires to loose.

Note

The wire gauge for the terminal block should be in the range

between 12~ 24 AWG.

LED Indicators

The LED indicators located on the front panel display the power status

and network status of the Industrial switch; each has their own specific

meaning as the table shown below.

LED

Color

Description

Green

Power input 1 is active

Off

Power input 1 is inactive

Green

Power input 2 is active

Off

Power input 2 is inactive

Fault

Red

Power input 1 or 2 is inactive

Off

Power input 1 and 2 are both functional, or no power

inputs

1 ~ 8

LNK/ACT

(Upper LED)

Green

Connected to network

Flashing

Networking is active

Off

Not connected to network

1 ~ 8

Speed

(Lower LED)

Yellow

Connected to network at speed of 1000Mbps

Off

Not connected to network or not working at speed of

1000Mbps

9 ~ 10

LNK/ACT

Green

A network device is detected.

Blinking

The port is transmitting or receiving packets from

the TX device.

PoE

(IPGC only)

Green

Link to PD(PoE device)

Off

Link to none PoE device

This manual suits for next models

Table of contents

Other Lantech Switch manuals

Lantech

Lantech IPES/IES-0008B Series User manual

Lantech

Lantech IPGS-0005T-4-12V User manual

Lantech

Lantech LGS-2404 User manual

Lantech

Lantech IES-2008 User manual

Lantech

Lantech IES-3 Series User manual

Lantech

Lantech IPGS-5400-2P User manual

Lantech

Lantech IPES-3408GSFP User manual

Lantech

Lantech IES-5416DF Series User manual

Lantech

Lantech IPES-3408 Series User manual

Lantech

Lantech IPES-5416DF Series User manual

Lantech

Lantech LGS-2816C-RPS User manual

Lantech

Lantech IPES-2208CA User manual

Lantech

Lantech GE-800 User manual

Lantech

Lantech LES-2400-RPS User manual

Lantech

Lantech IES-3208C User manual

Lantech

Lantech IPGS-5424 User manual

Lantech

Lantech IPES-5208T-X Series User manual

Lantech

Lantech IPES-0208 Series User manual

Lantech

Lantech IPES-0104GT-4 User manual

Lantech

Lantech LGS-1104 User manual

Lantech

Lantech TPGS-L6216XT User manual

Lantech

Lantech IPES-5222T Series User manual

Lantech

Lantech IES-0008B Series User manual

Lantech

Lantech TGS-R6616XFT User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual