Lanner NCA-2510 User manual

Other manuals for NCA-2510

1

This manual suits for next models

6

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide

Cantek

Cantek NR310-4 user manual

© Lanner Electronics Inc. All Rights Reserved. All product specifications are subject to change without notice.

The rackmount rail kit can be purchased as an accessory for existing system

including models: NCA-2510, NCA-2512, NCA-2520, NCA-4010, NCA-4012,

NCA-4112, NCA-4025.

The rackmount kit contains the following items:

2x Fixed Brackets

2x Adjustable Brackets

4x Flat-head Screws

Ensure that you have the following parts and tools available:

2x Mounting Ears (Provided with system)

6x Mounting Ear screws

8x Rack-mounting screws

1x Screwdriver, number 2

You can mount the network appliance on four posts in a 19-in rack or cabinet by

using the rackmount kit.

Note: Installing the system in a rack requires two people: one person lifts the system

while the other secures it to the rack.

If you are installing multiple systems in one rack, install the lowest one first and

proceed upward in the rack.

1. Attach the mounting ears to the front of the system chassis, using three (3)

mounting ear screws on each side to secure. Then, attach the fixed brackets to

the sides of the system, using two (2) flat-headed screws on each side to secure.

2. Slide the system into the rack, and secure the mounting ears to the rack, using

two (2) rack-mounting screws on each side.

Note: Ensure the rear of the system is supported throughout the process of

mounting the system into the rack.

P/N: 086W000457000

© Lanner Electronics Inc. All Rights Reserved. All product specifications are subject to change without notice.

3. Slide the adjustable brackets into the fixed brackets attached to the sides of the

system.

4. Secure the adjustable brackets to the rack, using two (2) rack-mounting screws

on each side.

5. Installation is complete.

Mounting Installation Precautions:

The following should be considered for rack-mount or similar mounting installations:

The installation of this product must be performed by trained specialists; otherwise, a

non-specialist might create the risk of the system’s falling to the ground or other

damages.

For fixed mounting only. To prevent hazards, do not slide unit out on brackets or hang

unsecured system from brackets.

Do not stack additional weight on top of rack mount system.

Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient

strength for supporting the system or use of inappropriate installation components.

Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room

ambient. Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature (Tma) specified by the

manufacturer.

Reduced Air Flow - Installation of the equipment in a rack should be such that the

amount of airflow required for safe operation of the equipment is not compromised.

Mechanical Loading - Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

Circuit Overloading - Consideration should be given to the connection of the equipment

to the supply circuit and the effect that overloading of the circuits might have on

overcurrent protection and supply wiring. Appropriate consideration of equipment

nameplate ratings should be used when addressing this concern.

Reliable Grounding - Reliable grounding of rack mounted equipment should be

maintained. Particular attention should be given to supply connections other than direct

connections to the branch circuit (e.g. use of power strips).

P/N: 086W000457000