LaCie 301304U User manual

Table of contents

Other LaCie Storage manuals

LaCie

LaCie RUGGED BOSS SSD User manual

LaCie

LaCie Computer Drive User manual

LaCie

LaCie 301838U User manual

LaCie

LaCie rikiki 301907 User manual

LaCie

LaCie 12big Rack Serial 2 User manual

LaCie

LaCie Minimus User manual

LaCie

LaCie grand Hard Disk User manual

LaCie

LaCie d2 Professional User manual

LaCie

LaCie 300818 - SAFE Mobile 120 GB External Hard... User manual

LaCie

LaCie 301385U User manual

LaCie

LaCie Bigger Disk Extreme User manual

LaCie

LaCie Little Big Disk Quadra User manual

LaCie

LaCie Brick User manual

LaCie

LaCie LaCinema Classic User manual

LaCie

LaCie Rugged RAID Pro User manual

LaCie

LaCie iamaKey User manual

LaCie

LaCie 5BIG NAS PRO User manual

LaCie

LaCie Rugged Hard Disk User manual

LaCie

LaCie Porsche Design P 9231 User manual

LaCie

LaCie 301295U User manual

LaCie

LaCie Little Disk User manual

LaCie

LaCie Hard Drive User manual

LaCie

LaCie USB Key MAX User manual

LaCie

LaCie 301930 User manual

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

HP

HP StorageWorks MSL2024 Getting started

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

HP

HP P9000 user guide

Western Digital

Western Digital Ultrastar Data60 installation guide

Dell

Dell PowerVault MD3600f Series Getting started

CFI

CFI TERA STOR SATA RAID IV user manual

Quantum

Quantum PX506 Unpacking and installation instructions

Disassembly instructions for LaCie 301304U "Design by Neil

Poulton" external hard dri e:

Neil Poulton may be an award winning "industrial designer," but he's not an engineer. This thing is

a bit tricky to disassemble.

The black shiny plastic top is a single piece cover over a metal bottom plate. It is held in place by

plastic bumps on the inside edges of the cover that fit into slots in the metal bottom's vertical walls.

There are no screws.

There are two bumps along each of the long edges of the plastic cover, and two similar ones on the

short side with the ED light underneath. There are two smaller bumps placed closer together on

the power/USB/switch side of the drive, and between those is another sort of vertical grapple that

holds the cover down more firmly on that side.

First, here is what the top (plastic) part of the casing looks like, turned upside down. The various

snappy things are hilighted. We will release the B UE ones first, then the GREEN ones, and finally

the rear RED ones.

To open the case:

1. Use a thin plastic or metal thing (like a putty knife) to pry the plastic away from the metal

bottom on one of the long sides. Insert a CD or a credit card that you don’t care about into the

gap to hold it open.

2. Do the same thing with the other side. Your enclosure should now look like this:

(The masking tape isn't related to this procedure; I just like to

note the voltage and polarity of the power supply on devices

that don't come with such a label.

[12 volts 2 amps, + on the inside, - outside for this drive.])

3. Pry the side with the blue ED light under it (not the side with the power and USB connectors);

you should be able to get the drive to fall partway out of the cover on this side if you hold it

close to vertical and gently pry & rock the casing back & forth. ike this:

That's a nail file, not the

sharp knife

Bottom part

should fall

away from

top casing

like this

(careful)

4. Carefully wiggle the cover around until it comes free of the back part. The power switch, USB

port, and power connector are not attached to the top cover, but you should still be very careful

not to break them. Eventually the middle post/grapple thing should let go and the cover will

come off completely. Be careful not to drop the drive!

5. Remove the screws and the ED connector.

6. Gently, and very slowly, slide the drive forward away from the SATA connector. The connector

is soldered onto the board, so if it breaks you’ll need to re-solder a lot of tiny connections.

Remember to put the four screws back in when you reassemble the drive, otherwise the

only thing holding it in will be the SATA connector and it will probably break from the

stress!

Screws Screws

Disconnect this