Kramer WP-20 User manual

WP-20 Quick Start

P/N:

2900- 300919QS

Rev:

Scan for full manual

WP-20 Quick Start Guide

This guide helps you install and use your WP-20 for the first time.

Go to www.kramerav.com/downloads/WP-20 to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

WP-20 Wall plate

1 Power supply (12V DC)

1 Quick start guide

Step 2: Get to know your WP-20

US Version

EU / UK Version

Feature

Function

HDMI™LED

When HDMI is selected:

Lights orange when external audio is selected.

Lights green when embedded audio is selected.

LED is off when HDMI is not selected.

PC Graphics LED

When PC input is selected:

Lights orange when external audio is selected.

Lights green when there is no audio.

LED is off when the PC input is not selected

ON LED

The LED indicates the following:

Lights green –power is provided by a power adapter.

Lights orange –power is provided by PoE.

RESET Button

Short press to reset the device.

Long press (5 seconds) to reset the device to factory default parameters.

PC IN Input Connector

Connect to the PC graphics source (for example, a laptop).

HDMI IN Input Connector

Connect to an HDMI source (for example, a Blu-ray disk player).

ETHERNET RJ-45 Connector

Connect to the Ethernet LAN.

AUDIO IN 3.5mm Mini Jack

Connect to the unbalanced, stereo audio source (for example, the audio output of the

laptop).

US Version

EU / UK Version

Feature

Function

REMOTE 5-pin Terminal Block

Connect to the remote, contact-closure switches for remote control (see Step 8).

OPTION 4-way DIP-switch

Switches for setting the device behavior (see Step 4).

CONTROL 3-pin Terminal Block

Connect to the serial controller to control the WP-20 (for example, a PC).

AUDIO OUT 3-pin Terminal

Block

Connect to the unbalanced, stereo audio acceptor (for example, amplified speakers).

RS-232 3-pin Terminal Block

Connect to the PC to transfer data via RS-232 (for example, a serial controller for a

remote device).

12V DC Connector

Connect to the included power supply. Not needed on the WP-20 if there is a PoE

provider over HDBaseT.

GND Terminal

Connect to the common ground (optional).

HDBT OUT RJ-45 TP Connector

Connect to a compatible HDBT TP switcher or receiver (for example, the TP-780Rxr).

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Step 3: Connect inputs

Always switch OFF the power on each device before connecting it to your WP-20.

For best results, we recommend that you always use Kramer high-performance

cables to connect AV equipment to the WP-20.

RJ-45 Pinout:

For the Ethernet connector, see the

wiring diagram below:

PIN EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

Step 4: Set DIP switches

Video Switching Selection

Audio Switching Selection

DIP-

switch 1

DIP-

switch 2

Video Input Selection

DIP-

switch 3

DIP-

switch 4

Audio Input Selection

Off

Automatic –Last connected. Where

more than one source is connected,

the last source has priority.

Off

Automatic –Priority selection.

Embedded HDMI analog Audio In.

Off

Automatic –Priority selection.

HDMI 1 PC IN.

Off

Automatic –Priority selection.

Analog Audio In embedded HDMI.

Off

Manual

Off

Embedded HDMI

Manual

Analog Audio In

Step 5: Connect power

If the device is not powered via HDBT PoE, connect the 12V power supply to the WP-20 and plug the power supply into the

mains power.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Mount WP-20

Mount the device in a suitable wall box. We recommend opening all holes in the walls of the box to assist in cooling the

WP-20.

Step 7: Connect outputs

Step 8: Operate WP-20

Operate WP-20 via Protocol 3000

Default IP Parameters

Parameter

Values

Default

Device Name

Any alphanumeric string up to 14 chars (can include hyphen, but not at the beginning or end)

KRAMER_

DHCP

ON/OFF

OFF

IP Address

Any valid IP address

192.168.1.39

Mask

Any valid network mask

255.255.0.0

Gateway

Any valid gateway address

192.168.0.1

TCP Port

0 to 65535

5000

UDP Port

0 to 65535

50000

Default RS-232 Communication Parameters

Parameter

Values

Baud Rate

115200

Data Bits

Stop Bits

Parity

None

Command Format

ASCII

Default Web Pages Logon Authentication

Parameter

Values

Name

Admin

Password

Admin

Operate WP-20 via Remote contact-closure switches Operate WP-20 via Web Page

Feature

Function

Input selection /

VGA phase shift

switch

Short press –Input toggle

Long press –Adjusts the VGA

phase shift

Step-in switch

Activates the step-in function if

relevant

Analog audio output

volume increase

control

Short press –Increases the

volume one step (0.5dB)

Long press –Increases the

volume from -83dB to +24dB in 10

seconds

Analog audio output

volume decrease

control

Short press –Decreases the

volume one step (0.5dB)

Long press –Decreases the

volume from +24dB to -83dB in 10

seconds

Ground

Connect to the common side of

the switches

Step 9: Technical Specifications

INPUTS:

Video:

1 HDMI on an HDMI connector, 1 VGA on a 15-pin HD (F) connector

Audio:

1 Unbalanced stereo audio on a 3.5mm mini jack

OUTPUTS:

1 HDBaseT on an RJ-45 connector, 1 Unbalanced stereo audio on a 3.5mm mini jack

PORTS:

1 RS-232 3-pin terminal block, 1 Ethernet on an RJ-45 connector

CONTROLS:

Remote switches for input switching and volume control, reset switch

STANDARDS:

HDMI with Deep Color, x.v.Color™ and 3D, HDCP—works with sources that support

HDCP repeater mode, HDBT certified

MAX. ANALOG AUDIO LEVEL:

3.1V p-p

THD:

0.013%

SNR:

–70dB

SUPPORTED WEB

BROWSERS:

Windows 7 and higher: Internet Explorer (32/64 bit) version 11, Firefox version 30,

Chrome version 35

MAC: Chrome version 35, Firefox version 27, Safari version 7

MAXIMUM TRANSMISSION

DISTANCE:

180m (590ft) up to 1080p @60Hz @24bpp in extended mode

130m (430ft) up to 1080p @60Hz @36bpp in normal mode

100m (330ft) up to 4K @60Hz (4:2:0) in normal mode

POWER CONSUMPTION:

12V DC, 850mA

OPERATING TEMP:

0° to +40°C (32° to 104°F)

STORAGE TEMP:

–40° to +70°C (–40° to

158°F)

HUMIDITY:

10% to 90%, RHL non-condensing

COOLING:

Convection

ENCLOSURE TYPE:

Aluminum

DIMENSIONS:

2 Gang USA 11.6 cm x 5.1cm x 11.4cm (4.57” x 2.01” x 4.49”) W, D, H

2 Gang EU 15.1cm x 4.7cm x 8.6cm (5.94” x 1.85” x 3.39”) W, D, H

WEIGHT:

0.23kg (0.51lbs) approx.

SHIPPING WEIGHT:

0.51kg (1.12lbs) approx.

ENVIRONMENTAL

REGULATORY COMPLIANCE:

Complies with appropriate requirements of RoHs and WEEE

VIBRATION:

ISTA 1A in carton (International Safe Transit Association)

COMPLIANCE STANDARDS:

INCLUDED ACCESSORIES:

Power adapter

WARRANTY:

7 years parts and labor

Specifications are subject to change without notice at www.kramerav.com

Other manuals for WP-20

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction