Kohler K-3447 User manual

Installation Guide

Close-Coupled Top-Trip Toilets

K-3447, K-3456, K-3463,

K-3464, K-3555, K-14239

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1021797-2-B

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Before You Begin

CAUTION: Risk of personal injury or product damage. Handle

with care. Vitreous china can break or chip if the product is

handled carelessly.

IMPORTANT! Record the model number (from the label on the box)

in the Homeowners Guide for reference.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for damage.

If the existing toilet does not have a supply shut-off valve below

the tank, install one before installing the new toilet.

Provide an adequate amount of clearance for the toilet’s lift rod.

Clearance values are measured from the ﬂoor to the top of the

fully extended rod.

•K-3456, K-3555 and K-14239 require 37-5/8″(95.6 cm) of

clearance.

•K-3463 requires 37-1/8″(94.3 cm) of clearance.

•K-3444, K-3461 and K-3464 require 35″(88.9 cm) of clearance.

•K-3447 requires 34-3/8″(87.3 cm) of clearance.

10" Adjustable

Wrench

Supply

Shut-Off

Valve

Tape

Measure

Pipe Wrench

Tubing Cutter

Safety

Glasses

Sponge

Level

Plus:

• 5/16" T-Bolts w/ Nuts and Washers

• Putty Knife

• 1/2" Open-End Wrench

• 1/2" Nut Driver/Socket

• Hacksaw

Wax Seal

1021797-2-B 2 Kohler Co.

1. Remove the Existing Toilet

CAUTION: Risk of hazardous gases. If the new toilet is not

installed immediately, temporarily place a rag in the closet

ﬂange.

Turn off the water supply.

Flush the toilet.

Sponge out all remaining water from the tank.

Disconnect the supply shut-off valve, if present.

Remove the old toilet.

Remove the old wax seal from the ﬂoor with a putty knife.

Replace the old T-bolts with the new 5/16″diameter T-bolts.

T-Bolt

Scrape off the old

wax seal.

Closet

Flange

Kohler Co. 3 1021797-2-B

2. Install the New Toilet

Install or relocate the supply and outlet as necessary to conform

to the roughing-in dimensions.

Install a supply shut-off valve.

Lay the toilet down onto a padded surface.

From the bottom of the toilet, ﬁrmly press a new wax seal around

the toilet outlet.

Remove the temporary rag (if used) from the toilet ﬂange hole.

Align and lower the toilet over the ﬂange and T-bolts.

IMPORTANT! Do not lift or rock the bowl after placement. If you

break the watertight seal, you must install a new wax seal.

Apply your full body weight around the toilet to set the seal.

IMPORTANT! Do not overtighten the nut. Overtightening may

cause breakage or chipping of vitreous china.

Carefully tighten the nuts.

Bottom of Bowl

Wax Seal

Bolt Cap

Nut

Washer

Bolt Cap Base

T-Bolt

Closet Flange

1021797-2-B 4 Kohler Co.

3. Install the Tank

IMPORTANT! Risk of product damage. Overtightening the tank

bolts may cause breakage or chipping of the vitreous china.

NOTE: Do not remove the pre-assembled tank bolts from the bottom

of the tank. The nuts and washers for securing the tank to the bowl

are packaged separately.

Position the tank on the bowl by centering the gasket on the bowl

inlet.

Assemble the washers and nuts to the tank bolts.

Tighten the nuts until snug.

Verify that the tank is level both left to right and front to back.

Make sure the nuts are tight enough to achieve a watertight seal.

Tank Bolt

Washer

Brass Nut

Tank

Tank Bolt

Gasket

Viewing The

Assembly From

Under The Tank

Tank

Gasket

Bowl Inlet

Kohler Co. 5 1021797-2-B

4. Install the Lift Rod

Insert the ﬂange into the center of the tank cover.

Insert the lift rod through the O-ring, then into the ﬂange.

Hold the lift rod while placing the large washer and nut onto the

other end of the lift rod.

Hand tighten the nut until snug, then wrench tighten 1/4-turn.

Set the tank cover onto the tank so the cover bracket ﬁts under

the vitreous china tab located on the back of the tank wall.

Carefully set the cover onto the tank.

Carefully lift the front of the tank cover just enough to gain

access to the ﬂapper chain and lift rod.

Insert the ﬂapper chain S-hook into the middle hole in the lift

rod.

Be sure the cover bracket and the vitreous china tab are engaged.

Flange

Tank Cover

Nut

O-Ring

Lift Rod

Washer

Tank

Flapper Chain

Lift Rod

Tank

Flapper Chain

S-Hook

Tank

Cover

1021797-2-B 6 Kohler Co.

5. Connect the Supply and Make Adjustments

Connect the supply shut-off valve to the toilet supply shank.

Open the supply shut-off valve slowly to check for leaks. If the

connections have been properly assembled, a slight tightening of

the nuts should stop leakage.

Install the toilet seat according to the packed instructions.

Adjustments

Adjust the tank to the marked waterline.

Rotate the threaded rod clockwise to raise the water level or

counterclockwise to lower the water level as needed.

Test ﬂush the toilet several times, while checking all connections

for leaks, to ensure proper operation.

If the ﬂapper ball does not seat properly when the lift rod is

lowered, provide more ﬂapper chain by:

•Relocating the ﬂapper chain S-hook to the bottom hole in the lift

rod.

•Repositioning the ﬂapper chain S-hook on the ﬂapper chain.

If the toilet does not ﬂush when the lift rod is raised, remove

some of the slack in the ﬂapper chain by:

•Relocating the ﬂapper chain S-hook to the top hole in the lift rod.

•Repositioning the ﬂapper chain S-hook on the ﬂapper chain.

Ferrule

Supply

Shank Tubing

Compression

Washer

Compression

Nut

Supply

Shut-Off

Valve

Supply Shut-Off Valve

Connection

Coupling

Nut

Fill

Valve Nut

Seal

Washer

Waterline

Adjusting the Water Level

Threaded Rod

Kohler Co. 7 1021797-2-B

Connect the Supply and Make Adjustments (cont.)

Periodically check for leaks for several days following the

installation.

1021797-2-B 8 Kohler Co.

Guide d’installation

W.C. à couplage direct et levier de

déclenchement supérieur

Outils et matériels

Merci d’avoir choisi la compagnie Kohler

Nous apprécions votre engagement envers la qualité Kohler. Veuillez

prendre s’il vous plaît quelques minutes pour lire ce manuel avant de

commencer l’installation. Ne pas hésiter à nous contacter en cas de

problème d’installation ou de performance. Nos numéros de téléphone

et notre adresse du site internet sont au verso. Merci encore d’avoir

choisi la compagnie Kohler.

Avant de commencer

ATTENTION : Risque de blessure corporelle ou

d’endommagement du produit. Manipuler avec précaution. La

porcelaine vitriﬁée peut se briser ou se fendre si le produit est

manipulé avec négligence.

IMPORTANT ! Enregistrer le numéro de modèle (de l’étiquette sur

la boîte) dans le guide du propriétaire pour référence.

Respecter tous les codes de plomberie et de bâtiment locaux.

Inspecter soigneusement le nouveaux WC de tout défaut.

Si le W.C. existant n’a pas de valve d’arrêt sous le réservoir, en

installer une avant d’installer le nouveau W.C.

10" Clé à

molette Valve d'arrêt Mètre

ruban

Lunettes de

protection

Coupe

tuyau

Éponge

Niveau à bulle

Et:

Joint en cire

• Couteau à mastic

• Clé platte 1/2"

• Clé douille 1/2"

• Scie à métaux

• Boulon en T de 5/16" avec

écrous et rondelles

Clé à

griffes

Kohler Co. Français-1 1021797-2-B

Avant de commencer (cont.)

Prévoir un espace équivalant adéquat pour la tige de levage du

W.C. L’espace est mesuré du sol à la partie supérieure de la tige

de levage totalement étirée.

•K-3456, K-3555 et K-14239 requièrent un espace de 37-5/8″(95,6

cm).

•K-3463 requière un espace de 37-1/8″(94,3 cm).

•K-3444, K-3461 et K-3464 requièrent un espace de 35″(88,9 cm).

•K-3447 requière un espace de 34-3/8″(87,3 cm).

1021797-2-B Français-2 Kohler Co.

This manual suits for next models

Table of contents

Languages:

Other Kohler Toilet manuals

Kohler

Kohler K-3493 Assembly instructions

Kohler

Kohler ADAIR K-5171T-M User manual

Kohler

Kohler OVE K-17629T-2 User manual

Kohler

Kohler K-3489 Series Assembly instructions

Kohler

Kohler Heated French Curve K-4649 Assembly instructions

Kohler

Kohler WELLWORTH LITE K-3420 User manual

Kohler

Kohler REVE K-24766T-S User manual

Kohler

Kohler K-3589 Assembly instructions

Kohler

Kohler Persuade Circ K-3753 User guide

Kohler

Kohler BRAZN K-EX22381T-SL User manual

Kohler

Kohler LUSTRA User manual

Kohler

Kohler K-25044-SSL-47 User manual

Kohler

Kohler K-25839T-NSHC User manual

Kohler

Kohler ADAIR K- 5171T-ITSE User manual

Kohler

Kohler Irvine E915 User manual

Kohler

Kohler Englefield EVORA Back-to-Wall User manual

Kohler

Kohler K-3998M Assembly instructions

Kohler

Kohler MEMOIRS K-3429T User manual

Kohler

Kohler VEIL K-20534T-S User manual

Kohler

Kohler C3-201 Quiet-Close K-4744 User manual

Kohler

Kohler K-3437 User manual

Kohler

Kohler OVE Series User manual

Kohler

Kohler K-5889X Assembly instructions

Kohler

Kohler K-31636-0 User manual

Popular Toilet manuals by other brands

Toto

Toto Washlet TCF4911 Series installation guide

Grohe

Grohe Sensia ARENA user manual

Geberit

Geberit AQUACLEAN MERA CLASSIC user manual

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 user manual

American Standard

American Standard CONCEPT Cube TF-2704 installation manual

BIOLAN

BIOLAN ECO Instructions for installation, use and maintenance

Thetford

Thetford C260 Series user manual

KELISS

KELISS T162A Series instruction manual

BIOLAN

BIOLAN GARDEN TOILET Instructions for installation, use and maintenance

washloo

washloo Prestige user manual

JABSCO

JABSCO 37010 Series quick start guide

Drive

Drive TSE 150 operating instructions

Olympia

Olympia EPOQUE 69209 Installation and Maintenance

GSi

GSi TRACCIA 691711 installation instructions

DENCK

DENCK PURE-D user manual

Silent Venus

Silent Venus SVP600 Installation & maintenance

InBe

InBe IB/04.06050 installation instructions

Swiss Madison

Swiss Madison Carré SM-1T264 installation instructions