Kohler Vanity K-2604 Assembly instructions
Installation and Care
Guide
Vanity
K-2604, K-5288, K-5289
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
1267640-2-A
Tools and Materials
Before You Begin
CAUTION: Risk of property damage. Select 250 lb (113.4
kg) load bearing 5/16″lag bolts with a length to clear
obstacles in the wall and 5/16″washers. Calculate proper lag
bolt length by adding the following: 1-1/2″(38 mm) backing
material + wallboard thickness + back rail thickness.
IMPORTANT! Risk of product damage. Do not modify the vanity.
Doing so will compromise structural stability.
IMPORTANT! Risk of product damage. Use care when moving the
vanity to avoid impacting, sliding, or side-loading the legs.
NOTICE: Siliconized acrylic caulk must be used to secure the sink
to the vanity. Do not use 100% silicone sealant which will damage
the finish of the vanity.
NOTICE: The finished wall must be straight and plumb to ensure
proper support of the vanity and alignment of the sink and door.
Plus:
• Wood Screws
• 2x6s
• 5/16" Lag Bolts and Washers
[Min 250 lb (113.4 kg) Load Bearing]
• Socket Wrenches
• Siliconized Acrylic Caulk
1267640-2-A 2 Kohler Co.
1. Prepare the Site
NOTICE: If the K-2607 bridge cabinet will also be installed, extend
the backing material a minimum of 12″(305 mm) beyond the width
of the vanity on the side where the bridge will be installed.
NOTICE: To properly secure the vanity, the top of the required 2x6
backing material must be 32-1/2″(826 mm) from the finished floor.
Measure and mark 32-1/2″(826 mm) up from the finished floor.
This will be the height from the finished floor to the top of the
2x6 backing material.
Ensure there are no obstructions in the wall (such as wiring or
plumbing) from the marked height down to the floor. If there are
obstructions, select another area to install the vanity.
NOTICE: Extend the backing material beyond the width of the
vanity to the nearest stud to ensure proper support for the vanity.
Front-notch the studs 1-1/2″(38 mm) to ensure the 2x6 backing
material is flush against the studs.
Secure the 2x6 backing material to the studs with framing nails.
Rough-in the water supply and drain lines into the rough-in
plumbing area of the vanity.
NOTICE: The finished wall must be straight and plumb to ensure
proper support of the vanity and alignment of the sink and door.
2x6
Backing
Material
32-1/2" (826 mm)
Kohler Co. 3 1267640-2-A
Prepare the Site (cont.)
Complete the finished wall. Make sure the finished wall is
straight and plumb, and the floor is flat and perpendicular to the
finished wall.
1267640-2-A 4 Kohler Co.
2. Secure the Vanity
CAUTION: Risk of property damage. Select 250 lb (113.4
kg) load bearing 5/16″lag bolts with a length to clear
obstacles in the wall and 5/16″washers. Calculate proper lag
bolt length by adding the following: 1-1/2″(38 mm) backing
material + wallboard thickness + back rail thickness.
IMPORTANT! Risk of product damage. Use care when moving the
vanity to avoid impacting, sliding, or side-loading the legs.
With assistance, lift and place the vanity in position against the
finished wall. Do not drag the vanity into position.
Verify the vanity is level and the back rail is plumb against the
wall. If necessary, turn the leveler(s) to adjust the unit.
Using a 1/4″drill bit, drill pilot holes through the back rail and
the finished wall. Verify the pilot holes are positioned to ensure
the lag bolts will engage the 2x6 backing material.
Secure the vanity to the wall with two 5/16″lag bolts and
washers (not provided).
Install the Bridge Cabinet (Optional)
Refer to the installation instructions packed with the K-2607
bridge cabinet.
Pilot
Hole
Finished
Wall
Washer
Lag Bolt
Back Rail
Leveler
Kohler Co. 5 1267640-2-A
3. Install the Bathroom Sink
CAUTION: Risk of personal injury. Vitreous china sinks are
very heavy. Get help lifting and aligning the sink.
Install the faucet (if applicable) and drain to the sink. Refer to the
faucet and drain manufacturer’s installation instructions.
NOTICE: Siliconized acrylic caulk must be used to secure the sink
to the vanity. Do not use 100% silicone sealant which will damage
the vanity finish.
Run a 1/4″(6 mm) continuous bead of siliconized acrylic caulk
around the top of the vanity, as illustrated.
NOTE: The sink is properly positioned when: (1) the back edge of
the sink is flush against the finished wall and (2) the overhang on
the left, right, and front side of the sink is equal on each side of the
vanity.
With assistance, lift and properly position the sink on top of the
vanity.
Immediately wipe away any excess caulk that contacts the vanity.
Run a 1/8″(3 mm) bead of siliconized acrylic caulk along the top
edge of the sink where it contacts the finished wall.
Finished
Wall
1267640-2-A 6 Kohler Co.
4. Reverse Door Swing
(Optional - 24″only)
NOTE: To ease installation, get assistance supporting the door.
NOTE: The vanity comes with hinges installed on the inside left. To
reverse the door swing, use the included template (1181754-7) to
mount the brackets to the opposite side of the vanity.
Align the hinge hooks with the cup of the top bracket.
Slide the hinge onto the top bracket.
Clip the hinge onto the bracket to secure.
Repeat for the lower hinge.
Hook
Bracket
Cup
Kohler Co. 7 1267640-2-A
5. Adjust the Drawers
Remove
Slide the drawer out until fully extended.
From underneath, pull the release latches toward the center of the
drawer.
Lift the front of the drawer and pull toward you to disengage
from the rails.
Once removed, lay the drawer on a flat, protective surface.
Reinstall
Fully extend the rails.
Align the holes in the back of the drawer with the rail hooks.
Rotate the drawer down onto the rails, engaging the front drawer
holes with the rail pins.
From underneath, push the release latches into the rails to secure
the drawer.
Latch
Rail
Hook
Holes
Pin
1267640-2-A 8 Kohler Co.
6. Recommended Hardware Placement
Measure and mark the dimensions for the hardware as shown
above.
Drill a 3/16″(21 mm) pilot hole at each marking.
Drill a finished hole to size.
Insert a screw through each hole. Thread the knob onto the screw.
24” Vanity Installation
From the back side of the door, insert the screw through the
predrilled hole.
Thread the knob onto the screw. Tighten securely.
Repeat for the drawer.
K-5288: 6-1/16" (154 mm)
K-5289: 4-9/16" (116 mm)
4-3/4"
(121 mm)
1"
(25 mm)
Kohler Co. 9 1267640-2-A
Adjust the Door
Adjust
Refer to the illustration and note the screwdriver location for the
desired adjustment.
Remove
Apply a small amount of leverage to the door with one hand to
keep the door in the full open position.
With the other hand, press the clip to release the lower hinge
latch from the bracket.
Repeat for the upper hinge.
Move the door forward to slide the hinges off the brackets.
Reinstall
Apply a small amount of leverage to the door with one hand to
keep the door in the full open position.
With the other hand, align the top hinge with the top bracket.
Clip the hinge onto the bracket to secure.
Repeat for the lower hinge.
Open and close the door to ensure proper operation.
Care and Cleaning
Vitreous China and Fireclay
•Use a mild detergent such as liquid dishwashing soap and warm
water for cleaning. Do not use abrasive cleaners that may scratch
or dull the surface.
Adjustments
Side
Depth
Height
Bracket
Clip
1267640-2-A 10 Kohler Co.
Other manuals for Vanity K-2604
1
This manual suits for next models
2
Table of contents
Languages:
Other Kohler Bathroom Fixture manuals
Kohler
Kohler K-13689 Assembly instructions
Kohler
Kohler K-7605 Assembly instructions
Kohler
Kohler K-1681 User manual
Kohler
Kohler AIRFOIL 37273 Series User manual
Kohler
Kohler Components K-77980-4A-CP User manual
Kohler
Kohler ARCHER 72700X-4 User manual
Kohler
Kohler Kumin 97878 Operating manual
Kohler
Kohler K-T948 Assembly instructions
Kohler
Kohler K-24659T-L User manual
Kohler
Kohler QUICK-RELEASE QUIET-CLOSE K-17608T User manual
Kohler
Kohler Mira Decor User manual
Kohler
Kohler Archer K-1122-GHLA User manual
Kohler
Kohler Triton K-T7019 User manual
Kohler
Kohler ENGLEFIELD SAPPHIRE User manual
Kohler
Kohler K-557 User manual
Kohler
Kohler K-15815 User manual
Kohler
Kohler K-18486 Assembly instructions
Kohler
Kohler K-9674 User manual
Kohler
Kohler Mira Vie User manual
Kohler
Kohler K-16280 Assembly instructions
