Kohler K-8034 User manual
Installation Guide
Lighted Rain Panel
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-8034 K-8038
1078520-2-A
IMPORTANT INSTRUCTIONS
WARNING: When using electrical products, basic
precautions should always be followed, including the
following:
DANGER: Risk of electric shock. Connect only to circuits
protected by a Ground-Fault Circuit-Interrupter (GFCI) or
Residual Current Device (RCD). Grounding is required. The
unit should be installed and grounded by a qualified service
representative.
WARNING: Risk of electric shock. A licensed electrician
should route all electrical wiring.
WARNING: Risk of electric shock. Disconnect power before
servicing.
WARNING: Risk of injury or property damage. Please read
all instructions thoroughly before beginning installation.
CAUTION: Risk of electric shock or product damage. Make
sure the power cord is unplugged before removing the PDS
access cover.
NOTICE: Follow all plumbing, electrical, and building codes.
NOTICE: Provide generous, unrestricted service access to the
Power Data Supply (PDS). Provide access for servicing. This access
must be located immediately next to the PDS. Refer to the
roughing-in information.
1078520-2-A 2 Kohler Co.
Specifications
Shower Installation Application Ceiling-mount only
Ambient Temperature Max 104°F (40°C)
Maximum Relative Humidity 95% non-condensing
Power Data Supply (PDS) 100-240 VAC, 50-60 Hz, 1.7 A
PDS Power Cable Length 3 ft (0.91 m)
Chroma Data Cable Length 30 ft (9.14 m)
Chroma Power Cable Length 30 ft (9.14 m)
Tools and Materials
Sealant
Tape
• (4) 2-1/2" nipples
• Female fittings
• 1/2" copper tubing
• 2x4s and 2x6s
• Conventional woodworking
tools and materials
• #8 x 1-1/2" drywall screws
• Standard wood or drywall
screws
Phillips
Screwdriver
Plus:
Note: All nipples and fittings
are 1/2" NPT
5/64" and 5/32"
Hex Wrenches
Socket Wrench with
11 mm or 7/16" Socket
and Extension
Masking
Tape
Soldering
Supplies
Kohler Co. 3 1078520-2-A
Roughing-In
21"
(53.3 cm)
20-1/8"
(51.1 cm)
19-5/16"
(49 cm)
4-7/8" (12.4 cm)
Min Clearance
Bottom Face of
Ceiling Joist
3-11/16"
(9.3 cm)
9-5/8" (24.4 cm)
1/2" NPT
K-8038
4-13/16"
(12.2 cm)
3-5/16"
(8.4 cm)
K-8034
3-1/2" (8.9 cm)
Min Clearance
Bottom Face of
Template/Cradle
Sprayface Detail
Chroma Data Cable
30' (9.1 m)
30' (9.1 m)
Chroma Power Cable
2" (5.1 cm)
8-13/16"
(22.4 cm)
5/16"
(8 mm)
3-1/2"
(8.9 cm)
1/8" (3 mm)
8-1/4"
(21 cm)
5-1/2"
(14 cm)
1078520-2-A 4 Kohler Co.
Before You Begin
Observe all local plumbing, building, and electrical codes.
Read these instructions and determine all required components
along with their installation locations before beginning this
installation.
This product is designed for ceiling-mount installation only. Do
not install to a shower wall.
This manual covers vertical installation of the Power Data Supply
(PDS) in a service closet or 2x6 stud pocket. If the wall is
enclosed, an access panel must be provided for servicing.
The PDS may also be mounted under the floor joists. If mounting
under the floor, the unit must not be enclosed.
The PDS must be located within 25 ft (7.62 m) of the rain panel.
Inspect the supply piping for damage. Replace as necessary.
A licensed electrician should install a 15 A 120 V GFCI/RCD
electrical outlet within a service closet or 2x6 stud framing with
access panel, not more than 2 ft (0.61 m) from the intended
mounting location of the PDS.
The PDS may be hardwired. For optional hardwire installation of
the PDS, order Service Kit #1078031.
To reduce the risk of electric shock, locate the outlet, PDS, and
overhead rain panel within proximity to each other to allow for
each cable to have a drip loop.
Kohler Co. reserves the right to make revisions in the design of
products without notice, as specified in the Price Book.
Kohler Co. 5 1078520-2-A
1. Determine Components
Speakers
AC Power AC Power
Media Module
Router
Computer Internet
Audio
Source
If a steam generator
is not used, connect
the PDS directly to
the media box.
Incandescent
Lighting
AC Power
Power Data
Supply (PDS)
Steam
Adapter
Digital
Interfaces
Steam Generator
Digital
Mixing Valve
Lighted Rain Panel
1078520-2-A 6 Kohler Co.
Determine Components (cont.)
A 30 ft (9.14 m) power cable is supplied for connecting the
overhead rain panel to the PDS. A 30 ft (9.14 m) data cable is
supplied for connecting the PDS to the media module or steam
adapter.
Determine all required components along with their installation
locations before beginning the overhead rain panel installation.
Kohler Co. 7 1078520-2-A
2. Prepare the Site
The PDS is designed to fit within a service closet or 2x6 stud
cavity with access panel. The service closet or access panel must
be located less than 30 ft (9.14 m) from the overhead rain panel.
Recommended maximum distance is 25 ft (7.62 m).
If mounting boards are required, they should be positioned to
allow adequate surface area to attach the PDS via the existing
mounting holes on both ends of the PDS box.
Install a 120 V GFCI/RCD electrical outlet within the service
closet or 2x6 stud framing, within 24” (61 cm) of the PDS. Locate
the outlet in close proximity to the PDS to allow enough cable to
create a drip loop.
Note: For hardwire installations, order Service Kit #1078031.
Outlet
Drip Loop
2x6
Position
to far left.
Power Data Supply
Mounting Board
8-1/4" (21 cm)
2x6 Stud Cavity
6" (15.2 cm) Min
1078520-2-A 8 Kohler Co.
3. Install the Power Data Supply
Orient the PDS box within the service closet or access panel to
allow room for cover removal and connecting the cables. If
possible, connect the cables through the side holes rather than
those on the cover to avoid complicated cover removal for
servicing.
If installing the PDS within a 2x6 stud cavity, position it to the far
left of the cavity to allow room for connecting the cables to the
side holes.
Attach the PDS to structural framing or other secure surface using
standard wood or drywall screws (not supplied). Mounting
boards may need to be installed between stud framing.
Route the Chroma data cable from the PDS to the media module
or steam adapter.
Route the Chroma power cable from the PDS to the overhead rain
panel location.
Kohler Co. 9 1078520-2-A
4. Install the Supply Piping – Single Supply
Route the water supply lines.
Use the provided soldering template to construct a pressure
balancing loop; this will ensure proper alignment with the
product.
Assemble the pressure balancing loop with a tee positioned over
each of the four raised locations on the soldering template.
Solder the assembly while it is still attached to the soldering
template.
Remove the pressure balancing loop assembly from the soldering
template.
Connect the pressure balancing loop to the water supply.
Do not strap the pipes.
Temporarily install a nipple to each tee. Do not use any sealant.
Pressure
Balancing Loop
Soldering
Template
1/2" NPT Nipple
Pressure
Balancing
Loop
Clamp each tee
to template
during soldering.
6-3/4" (17.2 cm)
Soldering Template
6-3/4"
(17.2 cm)
9-5/8"
(24.4 cm) D.
1078520-2-A 10 Kohler Co.
Other manuals for K-8034
1
This manual suits for next models
1
Table of contents
Languages:
Other Kohler Bathroom Fixture manuals
Kohler
Kohler K-5264 Operating manual
Kohler
Kohler PURIST UPGRADE K-99167T User manual
Kohler
Kohler Karat K-17399 User manual
Kohler
Kohler K-671 Assembly instructions
Kohler
Kohler K-10332 User manual
Kohler
Kohler K-704410 Assembly instructions
Kohler
Kohler Elevation 76665T-E User manual
Kohler
Kohler K-484 User manual
Kohler
Kohler K-475 User manual
Kohler
Kohler MARGAUX K-16232-4-SN Assembly instructions
Kohler
Kohler K-6956 User manual
Kohler
Kohler ODEON K-8827T User manual
Kohler
Kohler Sonata K-1641 User manual
Kohler
Kohler K-6855 Assembly instructions
Kohler
Kohler K-809 Quick start guide
Kohler
Kohler NEW PURIST K-701575T User manual
Kohler
Kohler ARCHER 7501X-4 User manual
Kohler
Kohler K-98804K User manual
Kohler
Kohler IRON/IMPRESSIONS K-3051-8 User manual
Kohler
Kohler K-T130 Assembly instructions
