Klein Tools ET60 User manual

INSTRUCTION MANUAL

ET60

600V

FRANÇAIS pg. 17

ESPAÑOL pg. 9

Electronic

AC/DC Voltage Tester

• MODERN

SOLID-STATE

DESIGN

• LOW IMPEDANCE

• DOES NOT

USE A BATTERY

• INTEGRATED

TEST LEAD

HOLDER

ENGLISH

GENERAL SPECIFICATIONS

Klein Tools ET60 is a solid-state, low impedance, electronic voltage

tester. It measures AC/DC voltages up to 600V. The ET60 does

not

require batteries; it is powered by the applied voltage.

• Operating Altitude: ≤ 6562 ft. (2000 m)

• Relative Humidity: <90% non-condensing

• Operating Temperature: 5°F to 113°F (-15°C to 45°C)

• Storage Temperature: -4°F to 140°F (-20°C to 60°C)

• Battery Type: None (powered by applied voltage)

• Dimensions: 5.67" x 2.35" x 1.44" (144 x 59.8 x 36.5 mm)

• Weight: 3.2 oz (92 g) without test leads

• Calibration: Accurate for one year

• Standards:

Conforms to: EN61326-1:2013,

EN61326-2-2:2006, EN61010-1:2010,

EN61010-2-030:2010, EN61010-031/A1:2008

• Pollution degree: 2

• Drop Protection: 9.8 ft. (3m)

• Ingress Protection:

IP54 (except test lead jacks, see WARNINGS)

• Safety Rating: CAT IV 600V, Class2, Double insulation

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC

EN61326-1:2013

. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

ELECTRICAL SPECIFICATIONS

• Voltage Level Indicators: 12V, 24V, 48V, 120V, 208V, 240V,

277V, 480V, 600V

• Voltage Type Indicators: DC Positive, DC Negative,

both DC polarities "on" indicates AC

• AC Frequency: 45Hz to 66Hz

• Maximum Measurable Voltage:

600V RMS (displayed by LEDs)

• Minimum Voltage Detectable:

Approx. 10V AC RMS or 10V DC

• Input Impedance:

16kΩ at 120V (Inherent Low Impedance Testing)

• Loop Current: 6mA to 9mA at 120V

• Usage Duty Cycle (Above 240V):

30 seconds continuous use

followed by 240 seconds (4 minutes) recovery time

• Accuracy: LEDs illuminate fully typically at approx. >90%

of indicated voltage, and will illuminate partially when

approaching this value

Specifications subject to change.

WARNINGS

To ensure safe operation and service of the meter, follow these

instructions. Failure to observe these warnings can result in

severe injury or death.

• Before each use verify tester operation by measuring a known voltage.

• Never use the tester on a circuit with voltages that exceed the

category based rating of this tester.

• Do not use the tester during electrical storms or in wet weather.

• Do not use the tester or test leads if they appear to be damaged.

• Use only with CAT IV rated test leads.

• Ensure tester leads are fully seated, and keep fingers behind

the finger guards and away from the metal probe contacts

when making measurements.

• Use caution when working with voltages above 25V AC RMS

or 60V DC. Such voltages pose a shock hazard.

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury

where hazardous live conductors are exposed.

• This is a Low Impedance (LoZ) tester, it should not be used in

circuits or situations where damage or adverse effects may be

caused by a ~ 16kΩ load.

• Tester is IP54 dust & water resistant. Following any contact

with water, thoroughly dry tester and test lead jacks prior to

subsequent use.

SYMBOLS ON TESTER

AC Alternating Current DC Direct Current

Positive DC Polarity or

Positive Lead Inupt

–

Negative DC Polarity

COM Common / Negative Lead Input

Double Insulated Class II Ground

Warning or Caution

Risk of Electrical Shock

LoZ Indicates that this is a low-impedence tester

FEATURE DETAILS

ENGLISH

NOTE: There are no user-serviceable parts inside tester.

1. Test Lead Holders

2. Voltage Indicator LEDs

3. DC Polarity Indicators (indicates AC when both are illuminated)

4. Test Lead Jacks (bottom of tester)

Back of Tester

Front of Tester

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Connect test leads by inserting the black lead into the "COM" jack

and the red lead into the "+" jack. Do not test if leads are improperly

seated. Results could cause intermittent display readings. To ensure

proper connection, firmly press leads into the input jack completely.

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CATIII / CATIV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

5/32"

(4 mm)

.7" (18 mm)

INCORRECT

CORRECT

ENGLISH

OPERATING INSTRUCTIONS

MEASURING VOLTAGE

Apply test leads to the system under test to measure voltage; the

LED’s will light up indicating the voltage present. When DC voltage

is detected the +or –polarity indicator will illuminate revealing

the polarity. When AC voltage is detected, both +and –polarity

indicators will be illuminated at the same time.

NOTE: Test-leads seated in the lead holders on the back of the ET60

are spaced correctly to test tamper-resistant US-style outlets.

Measuring above 240V

should be limited to

30 seconds continuous,

followed by a recommended

recovery time of at least

240 seconds (4 minutes).

GHOST/STRAY VOLTAGES

The low input impedance of ~16kΩ reduces the possibility of falsely

reading ghost or stray voltages on non-energized circuits.

GFCI TESTING

Check the GFCI receptacle user manual for more information.

Always contact a qualied electrician to resolve wiring problems.

Operate the test button on the GFCI receptacle. If the GFCI circuit

does not trip, the receptacle is not operating properly.

To test the functionality of a GFCI-protected receptacle, apply leads to

the hot/live and ground terminals for 7 seconds.

• If the GFCI receptacle is wired properly,

the GFCI will trip and the circuit will become

de-energized. The ET60 tester will stop

indicating voltage.

• If the GFCI receptacle is incorrectly wired, the

power to the circuit will remain and the ET60

will continue to indicate voltage

To resolve wiring or GFCI concerns, contact a qualied electrician.

CAUTION: The maximum testing voltage is 600V. Voltages in

excess of 600V will illuminate the 600V LED indicator. No other

warnings will be delivered for voltages above 600V. Testing voltages

above 600V should not be attempted under any circumstances.

CLEANING

Disconnect test leads. Clean the instrument by using a damp cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Do not expose to high temperatures or humidity. After a period of

storage in extreme conditions exceeding the limits mentioned in

the General Specifications section, allow the instrument to return to

normal operating conditions before use.

WARRANTY

www.kleintools.com/warranty

DISPOSAL /RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov or www.erecycle.org

for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

[email protected]

www.kleintools.com

NOTES

ENGLISH

ESPAÑOL

MANUAL DE INSTRUCCIONES

ET60

600 V

Probador de voltaje

CA/CD electrónico

• DISEÑO

MODERNO

EN ESTADO SÓLIDO

• BAJA IMPEDANCIA

• NO EMPLEA

BATERÍAS

• SOPORTE PARA

CABLES DE

PRUEBA

INCORPORADO

ESPAÑOL

ESPECIFICACIONES GENERALES

ET60 de Klein Tools es un probador de voltaje eléctrico en estado

sólido de baja impedancia. Mide voltaje de CA/CD hasta 600V. ET60

requiere el uso de baterías, ya que funciona con el voltaje aplicado.

• Altitud de funcionamiento: ≤ 6562pies (2000m)

• Humedad relativa: <90% sin condensación

• Temperatura de operación: 5°F a 113°F (-15°C a 45°C)

• Temperatura de almacenamiento:

-4°F a 140°F (-20°C a 60°C)

• Tipo de batería: ninguno (funciona con el voltaje aplicado)

• Dimensiones: 5,67" × 2,35" × 1,44" (144 × 59,8 × 36,5mm)

• Peso: 3,2oz (92g) sin los cables de prueba

• Calibración: precisa durante un año

• Normas:

Cumple con: EN61326-1:2013,

EN61326-2-2:2006, EN61010-1:2010,

EN61010-2-030:2010, EN61010-031/A1:2008

• Grado de contaminación: 2

• Protección ante caídas: 9,9pies (3m)

• Protección contra el ingreso de objetos sólidos y líquidos:

IP54 (excepto para los conectores de cables de prueba,

consulte la sección ADVERTENCIAS)

• Clasicación de seguridad: CATIV 600V, clase2,

doble aislamiento

CATIV: La categoría IV de medición es aplicable a los

circuitos de medición y prueba conectados a la fuente de la

instalación de suministro eléctrico de un edificio.

• Entorno electromagnético: IEC

EN61326-1:2013

. Este equipo

cumple con los requisitos apropiados para su uso en entornos

electromagnéticos básicos y controlados como propiedades

residenciales, establecimientos comerciales e instalaciones de

industria ligera.

Especificaciones sujetas a cambios.

ESPAÑOL

Table of contents

Languages:

Other Klein Tools Test Equipment manuals

Klein Tools

Klein Tools Coax Explorer VDV512-057 User manual

Klein Tools

Klein Tools ET510 User manual

Klein Tools

Klein Tools NCVT-6 User manual

Klein Tools

Klein Tools ET45 User manual

Klein Tools

Klein Tools ET250 User manual

Klein Tools

Klein Tools VDV Scout Pro 3 User manual

Klein Tools

Klein Tools NCVT-1 User manual

Klein Tools

Klein Tools VDV Scout Pro 2 VDV501-098 User manual

Klein Tools

Klein Tools ET270 User manual

Klein Tools

Klein Tools ET40 User manual

Klein Tools

Klein Tools RT210 User manual

Klein Tools

Klein Tools NCVT-6 User manual

Klein Tools

Klein Tools RT310 User manual

Klein Tools

Klein Tools ET250 User manual

Klein Tools

Klein Tools LAN Scout Jr. VDV526-052 User manual

Klein Tools

Klein Tools NCVT-1XT User manual

Klein Tools

Klein Tools NCVT-1XT User manual

Klein Tools

Klein Tools VDV Scout Pro 3 User manual

Klein Tools

Klein Tools GL1200 User manual

Klein Tools

Klein Tools VDV Commander VDV501-097 User manual

Klein Tools

Klein Tools LAN Scout Jr. VDV526-052 User manual

Klein Tools

Klein Tools NCVT-2P User manual

Klein Tools

Klein Tools NCVT-1P User manual

Klein Tools

Klein Tools HVNCVT1 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual