Klein Tools ET250 User manual

INSTRUCTION MANUAL

ET250

600V

FRANÇAIS pg. 17

ESPAÑOL pg. 9

Digital AC/DC Voltage &

Continuity Tester

• AUTOMATICALLY

SELECTS

MEASUREMENT

MODE

• MODERN

SOLID-STATE

DESIGN

• TEST GFCI

PROTECTED

CIRCUITS

• INTEGRATED

WORKLIGHT

• BUILT-IN

TEST LEAD

HOLDERS

• BACKLIT

LCD DISPLAY

ENGLISH

GENERAL SPECIFICATIONS

Klein Tools ET250 is a solid-state, digital voltage and continuity

tester. It measures AC/DC voltages up to 600V and tests for

continuity. Additionally, the ET250 tests GFCI protected circuits to

verify that the GFCI device is functioning appropriately. The tester

includes a backlight and worklight for working in reduced ambient

lighting conditions.

• Operating Altitude: ≤ 6562 ft. (2000 m)

• Relative Humidity: <80% non-condensing

• Operating Temperature: 5°F to 113°F (-15°C to 45°C)

• Storage Temperature: -4°F to 140°F (-20°C to 60°C)

• Battery Type: 3 x 1.5V AAA

• Dimensions: 6.06" x 2.33" x 1.64" (153.8 x 59.2 x 41.6 mm)

• Weight: 6 oz (170 g) without test leads

• Calibration: Accurate for one year

• Standards:

Conforms to EN61326-1:2013, EN61326-2:2013,

UL STD. 61010-1, 61010-2-030 and

61010-2-033.

Certified to CSA STD. C22.2 NO. 61010-1,

61010-2-030 and 61010-2-033

• Pollution degree: 2

• Drop Protection: 9.8 ft. (3m)

• Ingress Protection:

IP53 (except test lead jacks, see WARNINGS)

• Safety Rating: CAT IV 600V, Class 2, Double insulation

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC

EN61326-1:2013

. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

ELECTRICAL SPECIFICATIONS

• AC Voltage Range: 2 – 600V AC RMS (45 – 400Hz)

• DC Voltage Range: 2 – 600V DC

• Maximum Measurable Voltage:

600V RMS

• Resolution: 1V

• Accuracy: ±(2% + 2V)

• Test Current:

< 0.3mA at 120VAC RMS or 120 VDC

• Continuity: 0 – 270kΩ

• GFCI Test:

>6mA via button

• Nominal Voltage GFCI Testing: 10-135V AC at 50/60Hz in

3-wire outlet

• Auto-Detect: Tester auto-detects and selects VAC / VDC /

Continuity modes

Specifications subject to change.

WARNINGS

To ensure safe operation and service of the tester, follow these

instructions. Failure to observe these warnings can result in

severe injury or death.

• Before each use verify tester operation by measuring a known voltage.

• Never use the tester on a circuit with voltages that exceed the

category based rating of this tester.

• Do not use the tester during electrical storms or in wet weather.

• Do not use the tester or test leads if they appear to be damaged.

• Replacement test-leads should conform to EN 61010-031 and

be rated CAT IV 600V, 10A, or better. Do not use lower rated

test leads.

• Ensure tester leads are fully seated, and keep fingers behind

the finger guards and away from the metal probe contacts

when making measurements.

• Use caution when working with voltages above 25V AC RMS

or 60V DC. Such voltages pose a shock hazard.

• To avoid false readings that could lead to electric shock,

replace batteries when a low battery indicator appears.

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury

where hazardous live conductors are exposed.

• Tester is IP53 dust & water resistant. Following any contact

with water, thoroughly dry tester and test lead jacks prior to

subsequent use.

ENGLISH

FEATURE DETAILS

NOTE: There are no user-serviceable parts inside tester.

1. Test Lead Holders

2. Backlit LCD Display

3. Power-On/Off Button

4. Worklight Button

5. Backlight Button

6. GFCI Test Button

7. Test Lead Jacks (bottom of tester)

Back of Tester

Front of Tester

INCORRECT

CORRECT

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

USE PROPER SAFETY-RATED TEST LEADS

Connect test leads by inserting the black lead into the "COM" jack

and the red lead into the "+" jack. Do not test if leads are improperly

seated. Results could cause intermittent display readings. To ensure

proper connection, firmly press leads into the input jack completely.

SYMBOLS ON TESTER

Positive Lead Input COM Common / Negative Lead Input

Double Insulated Class II Ground

Warning or Caution

Risk of Electrical Shock

SYMBOLS ON LCD

Indicates presence of voltage

> 50V AC or DC

VAC AC Voltage

VDC DC Voltage

Audible Continuity Worklight

GFCI Ground Fault Circuit Interrupter

testing mode

Low Battery Indicator

FUNCTION BUTTONS

POWER-ON/OFF: Press the On/Off button to turn the tester on or off.

The tester will automatically power-ON if test leads are applied to

a circuit and it detects voltage >12V. The tester will automatically

power-OFF following 15 minutes of inactivity to conserve battery life.

BACKLIGHT: Press the Backlight button to turn on/off the backlight.

The backlight will automatically power off after 3 minutes of

inactivity to conserve battery life.

WORKLIGHT:

Press the Worklight button to turn on/off the worklight.

The worklight will remain on until turned off or tester powers off.

GFCI TEST: Press to perform a GFCI test. See

OPERATING

INSTRUCTIONS

for details.

AC/DC VOLTAGE (LESS THAN 600V)

Apply test leads to the system under test to measure voltage; the

voltage measured will be reflected in the display. The tester will

automatically detect the presence of AC or DC voltage and illuminate

the appropriate icon in the display.

NOTE: Test-leads seated in the lead holders on the back of the tester

are spaced correctly to test tamper-resistant US-style outlets.

AUTION: The maximum testing voltage is 600V. ‘OL’ will show

in the display if voltage in excess of 600V is detected. No other

warnings will be delivered for voltages above 600V. Testing voltages

above 600V should not be attempted under any circumstances.

ENGLISH

OPERATING INSTRUCTIONS

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CATIII / CATIV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

5/32"

(4 mm)

.7" (18 mm)

OPERATING INSTRUCTIONS

CONTINUITY

Remove power from circuit. Test for continuity by applying test leads

to the system being tested. The tester automatically enters continuity

testing mode. If resistance < 270kΩ is detected, an audible signal will

sound and the continuity icon "

" will show in the display indicating

continuity. If the circuit is open, "

" will show in the display.

DO NOT attempt to measure continuity on a live circuit.

GFCI TESTING

CAUTION: Check the GFCI Receptacle user manual for more

information. Always contact a qualied electrician to resolve wiring

problems. Operate the Test Button on the GFCI Receptacle. If the

GFCI circuit does not trip, the receptacle is not operating properly.

CAUTION: To resolve wiring or GFCI concerns, contact a

qualied electrician.

To test the functionality of a receptacle protected by a Ground Fault

Circuit Interrupter (GFCI), apply leads to the hot/live and ground

terminals. Press the GFCI Test button on the ET250 tester.

• If the GFCI device is wired properly, the GFCI will trip and the

circuit will become de-energized. The ET250 tester will stop

indicating voltage.

• If the GFCI receptacle is incorrectly wired, the power to the circuit

will remain and the ET250 will continue to indicate voltage. Contact

a qualified electrician to resolve wiring problems.

NOTE: The GFCI Test mode on this tester is deactivated in the

presence of voltages > 135V.

MAINTENANCE

BATTERY REPLACEMENT

When the Low Battery indicator

shows low battery strength ( ),

batteries must be replaced.

1. Remove 2 screws from

battery door.

2. Replace 3 x 1.5V AAA batteries

(note proper polarity).

3. Replace battery door and

fasten securely with screws.

o avoid risk of electric shock, disconnect leads from any voltage

source before removing battery door.

To avoid risk of electric shock, do not operate tester while

battery door is removed.

NOTE: There are no user-serviceable parts inside tester.

CLEANING

Disconnect test leads. Clean the instrument by using a damp cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Do not expose to high temperatures or humidity. After a period of

storage in extreme conditions exceeding the limits mentioned in

the General Specifications section, allow the instrument to return to

normal operating conditions before use.

WARRANTY

www.kleintools.com/warranty

DISPOSAL /RECYCLE

Do not place equipment and its accessories in the trash. Items must

be properly disposed of in accordance with local regulations. Please

see www.epa.gov or www.erecycle.org for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street Lincolnshire, IL 60069

1-877-775-5346

[email protected]

www.kleintools.com

ENGLISH

MANUAL DE INSTRUCCIONES

ET250

600V

Probador de continuidad y

voltaje CA/CD digital

• SELECCIONA

AUTOMÁTICAMENTE

EL MODO

DE MEDICIÓN

• DISEÑO

MODERNO

EN ESTADO SÓLIDO

• PRUEBA CIRCUITOS

PROTEGIDOS POR

GFCI

• LUZ DE TRABAJO

INCORPORADA

• SOPORTES PARA

CABLES DE

PRUEBA

INCORPORADOS

• PANTALLA LCD

RETROILUMINADA

ESPAÑOL

ESPECIFICACIONES GENERALES

Klein Tools ET250 es un probador de voltaje y continuidad digital

en estado sólido. Mide voltaje CA/CD de hasta 600V y prueba

continuidad. Además, prueba circuitos protegidos por GFCI para

comprobar que el dispositivo GFCI funciona correctamente. El

probador incluye retroiluminación y luz de trabajo para ambientes

poco iluminados.

• Altitud de funcionamiento: ≤ 6562pies (2000m)

• Humedad relativa: <80% sin condensación

• Temperatura de operación: 5°F a 113°F (-15°C a 45°C)

• Temperatura de almacenamiento: -4

F a 140

F (-20

C a 60

• Tipo de batería: 3 x 1.5V AAA

• Dimensiones

6,06" × 2,33" × 1,64" (153,8mm × 59,2mm × 41,6mm)

• Peso: 6 oz (170 g) sin los cables de prueba

• Calibración: precisa durante un año

• Normas:

Cumple con

EN61326-1:2013, EN61326-2:2013,

UL STD. 61010-1, 61010-2-030 and

61010-2-033.

Certificado según las normas

CSA STD. C22.2 NO. 61010-1,

61010-2-030 y 61010-2-033

• Grado de contaminación: 2

• Protección ante caídas: 9,8pies (3m)

• Protección contra el ingreso de objetos sólidos y líquidos:

IP53 (excepto para los conectores de cables de prueba,

consulte la sección ADVERTENCIAS)

• Clasicación de seguridad: CATIV 600V, clase2, doble

aislamiento

CATIV: La categoría IV de medición es aplicable a los

circuitos de medición y prueba conectados a la fuente de la

instalación de suministro eléctrico de un edificio.

• Entorno electromagnético: IEC

EN61326-1:2013

. Este equipo

cumple con los requisitos apropiados para su uso en entornos

electromagnéticos básicos y controlados como propiedades

residenciales, establecimientos comerciales e instalaciones de

industria ligera.

Especificaciones sujetas a cambios.

ESPAÑOL

Other manuals for ET250

Table of contents

Languages:

Other Klein Tools Test Equipment manuals

Klein Tools

Klein Tools Coax Explorer Plus User manual

Klein Tools

Klein Tools ET200 User manual

Klein Tools

Klein Tools NCVT-1 User manual

Klein Tools

Klein Tools NCVT-3P User manual

Klein Tools

Klein Tools VDV Scout Pro 3 User manual

Klein Tools

Klein Tools HVNCVT1 User manual

Klein Tools

Klein Tools GL1200 User manual

Klein Tools

Klein Tools LAN Scout Jr. VDV526-052 User manual

Klein Tools

Klein Tools ET200 User manual

Klein Tools

Klein Tools LAN Scout Jr. VDV526-052 User manual

Klein Tools

Klein Tools NCVT-6 User manual

Klein Tools

Klein Tools VDV Commander VDV501-097 User manual

Klein Tools

Klein Tools Toner-Pro User manual

Klein Tools

Klein Tools ET45 User manual

Klein Tools

Klein Tools ET140 User manual

Klein Tools

Klein Tools ET45 User manual

Klein Tools

Klein Tools ET250 User manual

Klein Tools

Klein Tools Coax Explorer 2 VDV512-100 User manual

Klein Tools

Klein Tools VDV Scout Pro 3 User manual

Klein Tools

Klein Tools LAN EXPLORER User manual

Klein Tools

Klein Tools RT210 User manual

Klein Tools

Klein Tools VDV Scout Pro 3 User manual

Klein Tools

Klein Tools HVCT1 User manual

Klein Tools

Klein Tools TraceAll VDV526-054 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual