Kenwood TK-5410 User manual

09 08 07 06 05 04 03 02 01 00

INSTRUCTION MANUAL

VHF P25 TRANSCEIVER

TK-5210

UHF P25 TRANSCEIVER

TK-5310

700/800MHz P25 TRANSCEIVER

TK-5410

Terminal Descriptions

Universal connector

It is possible to use a resin-based cover for the Universal connector.

No. Name Description Specification I/O

1 SSW Ext/Int Speaker Switch Input Hi: INT, Low: EXT I

2 SP+ BTL Output + for External Speaker Standard load 8 Ω O

3 SP- BTL Output – for External Speaker Standard load 8 Ω O

4 MSW Ext/Int MIC Switch Input Hi: INT, Low: EXT I

5 EMC External MIC Input Impedance: 1.8 kΩ I

6 ME External MIC GND – –

7 PTT External PTT Input Low: PTT ON I

8 PF Programable Function Key Input Input voltage: 0 V - 3.3 V I

9 OPT Aux I/O Port (for EXT Option) I: 0 V - 3.3 V

O: Standard load 25 kΩ I/O

10 E GND GND −

11 5V 5V 5V power supply output

Max output current: 140 mA O

12 TXD Serial Data Output Baud rate: 115200 bps max O

13 RXD Serial Data Input Baud rate: 115200 bps max I

14 NC Not used – –

Antenna Terminal

50 Ω impedance

Thank You

We are grateful you have chosen Kenwood for your land

mobile radio applications.

Models Covered bY This Manual

The models listed below are covered by this manual:

• TK-5210 (K/K2/K3/K7): VHF P25 Transceiver

• TK-5310 (K/K2/K3/K4/K5/K6/K7): UHF P25 Transceiver

• TK-5410 (K2/K3): 700/800MHz P25 Transceiver

noTiCes To The user

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment.

◆Refer service to qualified technicians only.

SAFETY: It is important that the operator is aware of and

understands hazards common to the operation of any transceiver.

Firmware Copyrights

The title to and ownership of copyrights for firmware embedded in

Kenwood product memories are reserved for Kenwood Corporation.

This device made under license under one or more of the following

US Patents: 4,590,473; 4,636,791; 4,716,407; 4,972,460; 5,148,482;

5,185,796; 5,271,017; 5,377,229; 5,502,767.

The IMBE™ voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights, and trade secrets of Digital Voice Systems, Inc. This voice

coding Technology is licensed solely for use within this Communications

Equipment. The user of this Technology is explicitly prohibited from

attempting to decompile, reverse engineer, or disassemble the Object

Code, or in any other way convert the Object Code into a human-

readable form.

The AMBE+2™ voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This

voice coding Technology is licensed solely for use within this

Communications Equipment. The user of this Technology is

explicitly prohibited from attempting to extract, remove, decompile,

reverse engineer, or disassemble the Object Code, or in any other

way convert the Object Code into a human-readable form. U.S.

Patent Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390,

#5,715,365, #5,649,050, #5,630,011, #5,581,656, #5,517,511,

#5,491,772, #5,247,579, #5,226,084 and #5,195,166.

iii

One or more of the following statements may be applicable:

FCC WARNING

This equipment generates or uses radio frequency energy.

Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this

equipment if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from

that to which the receiver is connected.

•Consult the dealer for technical assistance.

The RBRC Recycle seal found on Kenwood

nickel-cadmium (Ni-Cd) battery packs indicates

Kenwood’s voluntary participation in an industry

program to collect and recycle Ni-Cd batteries

after their operating life has expired. The RBRC

program is an alternative to disposing Ni-Cd

batteries with your regular refuse or in municipal

waste streams, which is illegal in some areas.

For information on Ni-Cd battery recycling in your area, call (toll

free) 1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment

to preserve our environment and conserve our natural resources.

The RBRC Recycle seal found on Kenwood nickel

metal hydride (Ni-MH) battery packs indicates

Kenwood’s voluntary participation in an industry

program to collect and recycle Ni-MH batteries

after their operating life has expired. The RBRC

program is an alternative to disposing Ni-MH

batteries with your regular refuse or in municipal

waste streams, which is illegal in some areas.

For information on Ni-MH battery recycling in your area, call (toll

free) 1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment

to preserve our environment and conserve our natural resources.

The RBRC Recycle seal found on Kenwood

lithium-ion (Li-ion) battery packs indicates

Kenwood’s voluntary participation in an industry

program to collect and recycle Li-ion batteries

after their operating life has expired. The RBRC

program is an alternative to disposing Li-ion

batteries with your regular refuse or in municipal

waste streams, which is illegal in some areas.

For information on Li-ion battery recycling in your area, call (toll

free) 1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment

to preserve our environment and conserve our natural resources.

PreCauTions

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specified by Kenwood.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Do not immerse the transceiver in water.

• When water gets into the microphone opening or the speaker

grill, the voice level may become incoherent or distorted. Lightly

shake the transceiver to remove the water from the speaker and/or

microphone before operating the transceiver.

• Always switch the transceiver power off before installing optional

accessories.

Turn the transceiver power off in the following locations:

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the

instructions and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons wearing pacemakers.

Turn the transceiver power off in the following locations,

unless the model is specifically qualified for such use

(Intrinsically Safe such as approved by Factory Mutual, CSA):

• In explosive atmospheres (inflammable gas, dust particles,

metallic powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while

the vehicle is running. When the airbag inflates, the transceiver

may be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if

any metallic parts are exposed from the antenna covering.

Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately,

remove the battery pack from the transceiver, and contact your

Kenwood dealer.

• Use of the transceiver while you are driving may be against

traffic laws. Please check and observe the vehicle regulations

in your area.

• Do not expose the transceiver to extremely hot or cold

conditions.

• Do not carry the battery pack (or battery case) with metal

objects, as they may short the battery terminals.

vii

CONTENTS

UNPACKING AND CHECKING EQUIPMENT....................................1

suPPlied aCCessories .........................................................1

PREPARATION ...................................................................2

baTTerY PaCk PreCauTions ....................................................2

insTalling/ reMoving The (oPTional) baTTerY PaCk...........................7

insTalling The (oPTional) anTenna............................................8

insTalling The belT CliP.......................................................8

insTalling The CaP over The universal ConneCTor............................9

insTalling The (oPTional) sPeaker/ MiCroPhone or headseT .................9

GETTING ACQUAINTED ....................................................... 10

disPlaY (k2/k3/k5/k6/k7 Models onlY)................................... 13

PROGRAMMABLE FUNCTIONS............................................... 15

BASIC OPERATIONS ........................................................... 18

swiTChing Power on/ oFF ................................................. 18

adjusTing The voluMe ....................................................... 19

seleCTing aZone and Channel .............................................. 19

TransMiTTing ................................................................ 20

reCeiving .................................................................... 22

SCAN............................................................................. 24

TeMPorarY Channel loCkouT................................................ 24

PrioriTY sCan ............................................................... 25

sCan reverT................................................................. 25

sCan PrograMMing (k2/k3/k5/k6/k7 Models onlY)

<Tk-5210/ Tk-5310 onlY> ................................................ 26

FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION

<TK-5210/ TK-5310 ONLY> ................................................... 28

selCall (seleCTive Calling)................................................. 28

sTaTus Message (k2/k3/k5/k6/k7 Models onlY).......................... 29

shorT Messages............................................................. 31

long Messages.............................................................. 31

gPs rePorT................................................................. 31

DTMF (DUAL TONE MULTI FREQUENCY) CALLS ......................... 32

Making adTMF Call ....................................................... 32

auTodial (k2/k3/k5/k6/k7 Models onlY) ................................. 33

viii

sTun Code <Tk-5210/ Tk-5310 onlY>.................................... 33

TRUNKING CALLS.............................................................. 34

Making aTelePhone Call ................................................... 34

reCeiving aTelePhone Call ................................................. 35

Making asTaTus Call ....................................................... 35

EMERGENCY CALLS ........................................................... 36

SCRAMBLER (FM) <TK-5210/ TK-5310 ONLY>/ ENCRYPTION (P25) ... 37

seCure (enCrYPTed) TransMission .......................................... 37

seleCTing The sCraMbler Code.............................................. 37

seleCTing The enCrYPTion keY............................................... 38

deleTing The enCrYPTion keY (k2/k3/k5/k6/k7 Models onlY) ............ 38

Password ProTeCTion (k2/k3/k5/k6/k7 Models onlY) ................... 38

SIGNALING...................................................................... 39

QuieT Talk (QT)/ digiTal QuieT Talk (dQT)................................ 39

oPTional signaling <Tk-5210/ Tk-5310 onlY>........................... 40

VOICE OPERATED TRANSMISSION (VOX) .................................. 41

voX gain level ............................................................. 41

voX oPeraTion.............................................................. 42

CLOCK (K2/K3/K5/K6/K7 MODELS ONLY) .................................. 43

CloCk adjusTMenT........................................................... 43

ADVANCED OPERATIONS ..................................................... 44

BACKGROUND OPERATIONS ................................................. 51

TiMe-ouT TiMer (ToT) ...................................................... 51

baTTerY saver ............................................................... 51

low baTTerY warning ...................................................... 52

signal sTrengTh indiCaTor (k2/k3/k5/k6/k7 Models onlY) .............. 52

CoMPander .................................................................. 53

busY Channel loCkouT (bCl) .............................................. 53

ouT oF range................................................................ 53

siTe Trunking ............................................................... 54

ConTrol Channel hunT...................................................... 54

voiCe annunCiaTion .......................................................... 54

PTT id ...................................................................... 54

VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT....................... 55

voiCe reCorder (k2/k3/k5/k6/k7 Models onlY) .......................... 55

voiCe guide.................................................................. 56

This manual suits for next models

Table of contents

Other Kenwood Transceiver manuals

Popular Transceiver manuals by other brands

Yaesu

Yaesu FT-7B manual

Texas Instruments

Texas Instruments TLK10232 user guide

Mizuho

Mizuho MX-2 Operating & assembly instruction

Blitz

Blitz MJ-398U instruction manual

Utilicom

Utilicom LongRanger 2050 Operator's manual

Standart

Standart HX290UKA Service manual

Altronix

Altronix Pace1PTM installation guide

Kirisun

Kirisun PT2208 instruction manual

ELECRAFT

ELECRAFT KX2 manual

Zodiac

Zodiac K3 user manual

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U manual

Siemens

Siemens PSO 4000 Quick reference guide

Midland

Midland G8E-BT Instruction guide

ComNav

ComNav Mariner X2 installation manual

Uniden

Uniden UH820 Series owner's manual

Standard Horizon

Standard Horizon HX320E owner's manual

Em-Trak

Em-Trak A100 Installation and user guide

HPE

HPE Aruba QSFP28 Guide