Keithley 8011 Instruction manual

Model 8011 High Current Test Socket Kit

Keithley Instruments, Inc. Connection instructions

28775 Aurora Road

Cleveland, Ohio 44139

1-888-KEITHLEY

http://www.keithley.com

PA-1032 Rev. A / April 2011 1

Model 8011 High Current Test Socket Kit connection instructions

WARNING

Before proceeding, please read, understand, and follow all safety precautions provided at the

end of this document (page 14).

The Model 8011 High Current Test Socket Kit is designed for testing high power devices with 2600A Series

SourceMeter instruments and the Model 2651A High Power SourceMeter Instrument at currents up at 50 A pulsed

and voltages up to 40 V.

The Model 8011 includes two test boards, the 8011-DTB and the 8011-CTB, and cables and connectors for

simplifying connections between the SourceMeter instruments and the device. The 8011-DTB Device Test Board is

designed for testing type TO-247 packaged parts and axial components. The 8011-CTB Customizable Test Board

provides a blank space for user customization — the user can use the socket type of his or her choice.

Figure 1. Model 8011 High Current Test Socket Kit*

*Not shown: PA-1032 (these instructions); full set of cables; 8010-317 insulator plugs; and 2600-KIT.

Model 8011 Connection Instructions

2 PA-1032 Rev. A / April 2011

Power and environmental specifications

For indoor use only.

Specification Value

Voltage limit 40 V DC maximum

Current limit 15 A DC maximum

Unpack and inspect the High Current Test Socket Kit

To unpack and inspect the High Current Test Socket Kit:

1. Inspect the box for damage.

2. Open the top of the box.

3. Remove the bags that contain the boards and accessories.

4. Carefully lift the High Current Test Socket Kit out of the box.

5. Inspect the materials for any obvious signs of physical damage. Report any damage to the shipping agent

immediately.

You should have received:

•TO-247 Device Test Board (8010-120; to re-order, use Keithley Model number 8010-DTB)

•Customizable Test Board (8010-130; to re-order, use Keithley Model number 8010-CTB)

•PA-1032 Model 8011 High Current Test Socket Kit Connection Instructions (this document)

•Four nylon hex standoffs with inserts on each end (ST-272-1)

•Four Phillips flat-head screws (#6-32 x 3/8)

•Two 8 in. (203.2 mm) stackable banana cables — one black (CA-560-0), one red (CA-560-2)

•One mounting plate (8011-301)

•Two 8-pin female plug connectors with screw terminal connections (CS-1629-8)

•Four 9 in. (228.6 mm) black cables with one stackable banana plug and one unterminated end (CA-567-0)

•Four 9 in. (228.6 mm) red cables with one stackable banana plug and one unterminated end (CA-567-2)

•One 120 in. (304.6 cm) green/yellow ground cable with lugs (CA-568-120)

•One #6-32 Keps®washer nut

•Two insulator plugs (quantity includes a spare plug) (8010-317)

•Two screw terminal connector kits (2600-KIT)

Model 8011 Connection Instructions

Specifications are subject to change without notice.

PA-1032 Rev. A / April 2011 3

Assembly instructions

NOTE

If you are customizing the 8010-130 Customizable Test Board, make customizations before assembling

the Model 8011.

See Figure 2 below.

Tools needed

•Medium Phillips head screwdriver

•5/16 in. nut driver or socket wrench

Assembly instructions

1. Select the TO-247 Device Test Board (8010-120) or Customizable Test Board (8010-130), as appropriate for

your application.

2. Connect one end of the ground cable to the ground screw at the center of the mounting plate.

3. Attach the ground cable with the #6-32 Keps®washer nut.

4. Thread the four nylon hex standoffs onto the four threaded posts on the mounting plate.

5. Place the 8010-120 or 8010-130 board on the standoffs.

6. Thread four of the Phillips flat-head screws through the 8010-120 or 8010-130 board.

7. Tighten the screws.

8. Attach the other end of the ground cable to protective earth (ground).

WARNING

The ground wire must be attached to a known safety earth (ground). Failure to attach the

ground wire to a known safety earth (ground) may result in electric shock.

Model 8011 Connection Instructions

4 PA-1032 Rev. A / April 2011

Figure 2. Model 8011 assembly

Four #6-32 x 3/8

Phillips flat-head screws

8010-130 Customizable Test Board

8010-120 TO-247 Device Test Board

Four ST-272-1 hex nylon standoffs

One 8011-301 mounting plate

One CA-568-120 green/yellow

ground cable with lugs

One #6-32 Keps® washer nut

Connect ground cable lug to protective earth (ground)

Model 8011 Connection Instructions

Specifications are subject to change without notice.

PA-1032 Rev. A / April 2011 5

Mounting instructions

The 8011-301 mounting plate should be used to secure your test board (8010-120 or 8010-130). It can also be

used to secure the assembled Model 8011 to a work surface using the mounting holes shown in Figure 3.

Figure 3. 8011-301 mounting plate dimensions

.156 in.

(3.962 mm)

5.250 in.

(133.35 mm)

2.625 in.

(66.675 mm)

.750 in

(19.05 mm)

4.500 in

(114.3 mm)

6.000 in

(152.4 mm)

Mounting holes

Model 8011 Connection Instructions

6 PA-1032 Rev. A / April 2011

NOTE

You can attach your own test board or testing fixture to the 8010-130 Customizable Test Board using the

#6-32 screw mounts provided.

Figure 4. 8010-130 Customizable Test Board dimensions

3.000 in.

(76.2 mm)

1.000 in.

(25.4 mm) .156 in.

(3.962 mm)

#6-32

.750 in.

(19.05 mm)

3.500 in.

(88.9 mm)

5.000 in.

(5 mm)

.250 in.

(6.35 mm)

4.250 in.

(107.95 mm)

3.750 in.

(95.25 mm)

1.750 in.

(44.45 mm)

Model 8011 Connection Instructions

Specifications are subject to change without notice.

PA-1032 Rev. A / April 2011 7

General guidelines

The High Current Test Socket Kit provides several types of connections to allow you to make connections to meet

the needs of your application.

In general, when making connections:

•Remove power from the SourceMeter instrument before making connections.

•Make connections to the SourceMeter instrument before making connections to the Model 8011 boards.

•Connect the force leads of the SourceMeter instrument to terminals 4, 5, and 6 of the Model 8011 boards.

Connect the sense leads to terminals 1, 2, and 3.

•Install the device under test (DUT) after making the SourceMeter instrument connections.

Use-cases are shown below that demonstrate some typical connections.

Use-cases

Two-terminal DUT using a Model 2651A set to local sense

NOTE

These instructions provide general information about connections to the Model 2651A. For detail on the

connections, see the Model 2651A user documentation.

Tools needed

•Small flat-head screwdriver

Instructions

1. Remove power from the Model 2651A.

2. Make connections as shown in Table 1 and Figure 5.

3. Install the 8010-317 insulator plug into the test socket.

4. Install the 2-terminal DUT into the axial posts labeled 4, 1, 3 and 6 on the 8010-120 board.

5. Return power to the Model 2651A.

6. Press the CONFIG key.

7. Press the SRC or MEAS key (the sense mode can be set from either the V-SOURCE or the V-MEAS menu).

8. If you pressed the SRC key, select V-SOURCE > SENSE-MODE.

9. If you pressed the MEAS key, select V-MEAS > SENSE-MODE.

10. Select 2-WIRE to enable local sense.

11. Test the device.

Model 8011 Connection Instructions

8 PA-1032 Rev. A / April 2011

Table 1. Connections for two-terminal device test (local sense)

Cable end Cable Cable end

Model 2651A rear panel CA-552-1 (supplied with the Model 2651A) Open

LO of CA-552-1 Black CA-560-0 8010-120 blue terminal 4

HI of CA-552-1 Red CA-560-2 8010-120 yellow terminal 6

Figure 5. Connections for two-terminal device test (local sense)

CA-560-0

(black)

2-Terminal DUT

Plug

HIGH CURRENT TEST SOCKET KIT

8011

RATINGS:

40V MAX.

15A DC MAX.

50A PULSE MAX.

From

Model 2651A

CA-552-1

(supplied with

Model 2651A) 8010-317 insulator plug

(insert into 3-pin socket)

CA-560-2

(red)

TO-247 Device Test

Board (8010-120)

Two-terminal DUT using a Model 2651A set to remote sense

Tools needed

•Small flat-head screwdriver

Instructions

1. Remove power from the Model 2651A.

2. Make connections as shown in Table 2 and Figure 6.

3. Install the 8010-317 insulator plug into the test socket.

4. Install the 2-terminal DUT into the axial posts labeled 4, 1, 3 and 6 on the 8010-120 board.

5. Return power to the Model 2651A.

Model 8011 Connection Instructions

Specifications are subject to change without notice.

PA-1032 Rev. A / April 2011 9

6. Press the CONFIG key.

7. Press the SRC or MEAS key (the sense mode can be set from either the V-SOURCE or the V-MEAS menu).

8. If you pressed the SRC key, select V-SOURCE > SENSE-MODE.

9. If you pressed the MEAS key, select V-MEAS > SENSE-MODE.

10. Select 4-WIRE to enable remote sense.

11. Test the device.

Table 2. Connections for two-terminal device test (remote sense)

Cable end Cable Cable end

Model 2651A rear panel CA-552-1 (supplied with the Model 2651A) Open

LO of CA-552-1 Black CA-560-0 8010-120 blue terminal 4

HI of CA-552-1 Red CA-560-2 8010-120 yellow terminal 6

Model 2651A rear panel CA-557-1 (supplied with the Model 2651A) CS-1629-8

Sense LO of CS-1629-8 Black CA-567-0 8010-120 blue terminal 1

Sense HI of CS-1629-8 Red CA-567-2 8010-120 yellow terminal 3

Figure 6. Connections for two-terminal device test (remote sense)

S LO

S HI

2-Terminal DUT

Plug

8010-317 insulator plug

(insert into 3-pin socket)

HIGH CURRENT TEST SOCKET KIT

8011

RATINGS:

40V MAX.

15A DC MAX.

50A PULSE MAX.

From

Model 2651A

CA-567-0

(black)

CA-560-0

(black)

CA-560-2

(red)

CS-1629-8

CA-552-1

(supplied with

Model 2651A)

CA-557-1

(supplied with

Model 2651A)

CA-567-2

(red)

From

Model 2651A

8010-120 TO-247

Device Test Board

Model 8011 Connection Instructions

10 PA-1032 Rev. A / April 2011

Three-terminal DUT using a Model 2651A and a single or dual channel

SourceMeter instrument

NOTE

If you are using a Model 2600A, do not set the output above 40 V. The Model 8011 is rated to 40 V.

You can use the Model 8011 with the 8010-120 board to test a three-terminal device using a Model 2651A High

Power System SourceMeter®Instrument and another SourceMeter instrument. This use-case is appropriate for the

following SourceMeter instruments:

•Model 2601A Single-Channel System SourceMeter Instrument

•Model 2611A Single-Channel System SourceMeter Instrument (200 V)

•Model 2602A Dual-Channel System SourceMeter Instrument

•Model 2612A Dual-Channel System SourceMeter Instrument (200 V)

Tools and equipment needed

•Small flat-head screwdriver

•Cable created using the 2600-KIT screw terminal connector kits (included with the Model 8011); the cable must

use wire that can support 3 A and 200 V

Instructions

1. Remove power from the SourceMeter instruments.

2. Make connections as shown in Table 3 and Figure 7.

3. Install the three-terminal DUT into the socket on the 8010-120 board.

4. Return power to the SourceMeter instruments.

5. On both SourceMeter Instruments:

a. Press the CONFIG key.

b. Press the SRC or MEAS key (the sense mode can be set from either the V-SOURCE or the V-MEAS

menu).

c. If you pressed the SRC key, select V-SOURCE > SENSE-MODE.

d. If you pressed the MEAS key, select V-MEAS > SENSE-MODE.

e. Select 4-WIRE to enable remote sense.

6. Test the device.

Table of contents

Other Keithley Test Equipment manuals

Keithley

Keithley S500 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley 1600A User manual

Keithley

Keithley 213 User manual

Keithley

Keithley 7158 User manual

Keithley

Keithley Interactive SourceMeter 2450 Installation and maintenance instructions

Keithley

Keithley 8009 User manual

Keithley

Keithley 7071 User manual

Keithley

Keithley 263 User manual

Keithley

Keithley 7012-S User manual

Keithley

Keithley S530 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley 2657A User manual

Keithley

Keithley 263 User manual

Keithley

Keithley 8010 User manual

Keithley

Keithley 4200-SCS User manual

Keithley

Keithley System SourceMeter 2602B User manual

Keithley

Keithley 2001-TCSCAN User manual

Keithley

Keithley S535 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley 261 User manual

Keithley

Keithley SourceMeter 2425 User manual

Keithley

Keithley 6521 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual