Keithley 213 User manual

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Find the Keithley 213 at our website: Click HERE

Model 213 Quad Voltage Source

Quick Reference Guide

A GREATER MEASURE OF CONFIDENCE

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

INTRODUCTION

This quick reference guide contains descriptions of the

features and operation of the Model 213. Also included is

a programming example using a PC controller.

Olggo. Keithley Instruments, Inc.

Instruments Division

Cleveland, Ohio, U. S. A.

Document Number: 213-903-01 Rev. A

+ 1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

TABLE OF CONTENTS

SAFETY WARNINGS ....................... 5

FRONT PANEL FAMlLtARtZATlON ........... 7

REAR PANEL FAMlLlARlZATtON ............. 9

DIP SWtTCH ......................... 9

ANALOG OUTPUT PORTS .............. 9

DlGtTAL INPUT/OUTPUT PORTS ........ 10

BASIC OPERATION ....................... 13

DAC PORTTRIGGERING ............... 13

INTERNAL SUFFER ................... 14

CONTROL MODES .................... 16

IEEE-488 PROGRAMMING .................. 19

DEVICE-DEPENDENTCOMMANDS ...... 19

SRQ MASK AND SERIAL POLL BYTE ..... 31

STATUS WORDS ..................... 32

KEYBOARD CONTROLLER PROGRAM ....... 38

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

SAFETY WARNINGS

The following safety warnings should be obsewed before

using Model 213 Quad Voltage Source. Refer to main

manual for detailed safety information and complete op-

eration instructions.

The Model 213 Quad Voltage Source is intended for use

by qualified personnel who recognize shock hazards and

are familiar with the safety precautions required to avoid

possible injury. Read over the manual carefully before

using the instrument.

Before operating the instrument, make sure the line cord

is connected to a properly grounded power receptacle.

Exercise extreme caution when a shock hazard is pre-

sent. Lethal voltages may be present on connsctorjacks.

The American National Standards fnstitute (ANSI) states

that a shock hazard exists when voltage levels greater

than 30V FtMSor42.4Vpeakare present. Agoodsafety

practice Is to expect that hazardous v&age Is pre-

sent In any unknown clrcuii before measuring.

Inspect the connecting cables, test leads, and jumpers

for possible wear, cracks, or breaks before each use.

For maximum safety, do not touch the Quad Voltage

Source connections, test cables or connections to any

other instruments white power is applied to the circuit un-

der test. Turn off att power and discharge any capacitors

before connecting or disconnecting cables or jumpers.

+ 5

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Do not touch any object which could provide a current

path to the commonside ofthecircuit undertestorpower

line (earth) ground.

Do not exceed the maximum signal levels of the instru-

ment, as shown on the rear panel and as defined in the

specifications and operation section of the instruction

manual.

tnstrumentation and accessories should not be con-

nected to humans.

Maintenance should only be performed by qualified SBW

ice personnel. Before performing any maintenance, dis-

connect the line cord and all test cables from the instru-

ment.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

FRONT PANEL

FAMILIARIZATION

Six LEDs on the front panel of the Model 213 Quad Volt-

age Source disolav the status of the interface fsee

Figure 1).

Ffgure 1. Front Panel Indicators

TALK-On when the unit is in the talker state, off whsn

the unit is in the idle or listener state.

LfSTEN - On when the unit is in the listener state, off

when the unit is in the idle or talker State.

SRQ - On when the unit has generated a service Is-

quest. oft when no SW is pending. (See Service Re-

quest Mask command for more information.)

ERROR-On when an error has occurred, off when no

error condition exists. (See Error Query command for

more information.)

+ 7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

TEST - Used in conjunction with the Test command to

verify that communication. ..__ ___,

n haa haen established with the

unit. The TEST light will flash wher I the unit is calibrating

in the auto-calibration mode. It will then remain tit when

finished.

POWER-On when power is applied to the unit and the

power switch on the back panel is in the on position (de-

pressed). Off if power is not present.

8 +

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

REAR PANEL

FAMILIARIZATION

DIP SWITCH

The Model 213 hasone S-position switch @WI) accessi-

ble from the rear panel. This switch determines the unit’s

IEEE address and its operating mode (normal or auto-

calibration). The switch is read only when the unit is pow-

ered on and should be set prior to applying power.

Figure 2 illustrates the factory default setting for SWI,

Figure 2. SW1 Factory Default Setttngs

ANALOG OUTPUT PORTS

The Model 213 can be thought of as four isolated digital

to analog converters occupying one IEEE-488 bus ad-

dress. Each port has a low (L), high (H), and ground

+ 9

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

(chassis ground) line. Cha*sis ground may be connected

lo the shield of shielded cable if this type of cable is used

lo carry the analog signals.

CAUTION

The maximum common-mode input

voltage (the voltage between output LO

and chassis ground) Is 500V peak. Ex-

ceeding this value may damage the In-

terface.

The pinouts for all four analog ports are labeled on the

real panel of the unit and are shown in Figure 3. Each

analog output is capable of sourcing and sinking a maxi-

mum current 0, ,OrnA.

PORT 1 PORT? PORT 3 PORT4

HLG HLG HLG HLG

. . . . . . . . . . . .

Figure 3. Analog Output Connector Pinout

DIGITAL INPUT/OUTPUT PORTS

The Model 213 has eight digital input lines and eight digi-

tal output lines.

Figure 4 illustrates the digital I/O edge connector as

viewed from the rear of the instrument.

10 +

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Table of contents

Other Keithley Test Equipment manuals

Keithley

Keithley 2657A User manual

Keithley

Keithley 7071 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley 4200-SCS User manual

Keithley

Keithley 8009 User manual

Keithley

Keithley S500 User manual

Keithley

Keithley 3330 User manual

Keithley

Keithley 6521 User manual

Keithley

Keithley S535 User manual

Keithley

Keithley 8101-4TRX User manual

Keithley

Keithley 1600A User manual

Keithley

Keithley 263 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley 261 User manual

Keithley

Keithley 2520 User manual

Keithley

Keithley 263 User manual

Keithley

Keithley S530 User manual

Keithley

Keithley 2001-TCSCAN User manual

Keithley

Keithley 7012-S User manual

Keithley

Keithley 2520INT User manual

Keithley

Keithley 8010 User manual

Keithley

Keithley System SourceMeter 2602B User manual

Keithley

Keithley Interactive SourceMeter 2450 User manual

Keithley

Keithley 2520 User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual