Küppersbusch KD 9650.0 E User manual

Bedienungsanleitung

Instructions Booklet

Mode d’emploi

Libretto Istruzioni

Gebruiksaanwijzing

Manual de instrucciones

KD 9650.0 E

14GB

CONTENTS

Dear Customer,

Ifyoufollowtherecommendations

containedinthisInstructionManual,your

appliancewillgiveyouconstanthighper-

formance and will remain efficient for

many years to come.

RECOMMENDATIONS AND SUGGESTIONS 15

CHARACTERISTICS 16

INSTALLATION 17

USE 20

MAINTENANCE 21

15GB

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting

fromincorrectorimproperinstallation.

• The minimum safety distance between the cooker top and the

extractor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply

guarantees adequate earthing.

Connecttheextractortotheexhaust flue throughapipe of minimum

diameter120mm.The route of the flue must beasshortaspossible.

• Do not connect the extractor hood to exhaust ducts carrying

combustionfumes(boilers, fireplaces, etc.).

• Iftheextractor is used in conjunctionwithnon-electricalappliances

(e.g. gas burning appliances), a sufficient degree of aeration must

beguaranteedinthe roomin orderto preventthebackflowofexhaust

gas.The kitchen musthavean openingcommunicatingdirectly with

the open air in order to guarantee the entry of clean air.

USE

• Theextractor hood has been designed exclusively for domestic use

toeliminatekitchen smells.

• Never use the hood for purposes other than for which it has ben

designed.

• Neverleavehighnakedflamesunderthe hoodwhen itisinoperation.

• Adjustthe flame intensitytodirect itontothe bottomofthe pan only,

making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use:

overheated oil can burst into flames.

• Thehoodshould not beusedbychildren or persons notinstructedin

its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before

carrying out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

650 mm min.

16GB

CHARACTERISTICS

Components

Ref. Q.ty Product Components

11 HoodBody,completewith:Controls,Light,Blower,

Filters

21 TelescopicChimneycomprising:

2.1 1 UpperSection

2.2 1 LowerSection

81 DirectionalAirOutletgrille

91 ReducerFlangeø150-120mm

10 1 Flangeø150mm

Ref. Q.ty Installation Components

7.2.1 2 UpperChimneySectionFixingBrackets

7.4 1 AirOutletConnection

11 8 WallPlugs

12a 8 Screws4,2x44,4

12c 6 Screws2,9 x 6,5

13 1 Gasket

Q.ty Documentation

1 InstructionManual

2.1

2.2

12a

12c

12a 7.2.1 11

7.4

17GB

INSTALLATION

Walldrillingandbracketfixing

Wallmarking:

• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of

the area in which the hood will be installed.

• Draw a horizontal line at 650 mm above the hob.

• Place bracket 7.2.1on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the

centre (notch) with the vertical reference line.

• Mark the wall at the centres of the holes in the bracket.

• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper

chimneysectionsupplied),aligningthecentre(notch)withtheverticalline.

• Mark the wall at the centres of the holes in the bracket.

• Mark a reference point as indicated at 116 mm from the vertical reference line and 335 mm above

the horizontal reference line.

• Repeat this operation on the other side.

• Drill ø 8 mm holes at all the centre points marked.

• Insert the wall plugs 11 in the holes.

• Fix the brackets using the 12a screws (4,2 x 44,4) supplied.

• Insert the two screws 12a(4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-6

mm between the wall and the head of the screw.

12a

335 X

116

650 min.

7.2.1

18GB

12a

ø 120ø 150

Mounting the hood body

• Before attaching the hood body, tighten the two

screws Vr located on the hood body mounting

points.

• Hook the hood body onto the screws 12a

• Fully tighten support screws 12a

• Adjust screws Vr to level the hood body.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

Wheninstalling the ductedversion,connectthe hood tothechimney using eitheraflexibleor rigid pipe

ø 150 or 120 mm, the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection,

insert the reducer flange 9on the hood body

outlet.

• Fixthepipeinpositionusingsufficientpipeclamps

(notsupplied).

• Remove any activated charcoal filters.

RECIRCULATION VERSION AIR OUTLET

• Lean the airoutlet junction 7.4 against the wall and place

it under the upper fixing bracket 7.2.1 centring it to the

vertical reference line.

• Mark the centre of the fixing slots.

• Drill ø 8 the marked points.

• Put the dowels 11 into the holes.

• Fix the flange 10 to the lower opening of the junction

piece 7.4.

• Fix the junction piece to the wall using the 2 screws 12a

(4,2x44,4)(supplied).

• Cut the gasket 13into two pieces of same size and place

them to the round shaped part of the junction piece.

• Connectthehoodairoutlet to the flange in the lower part

of the junction using a rigid or flexible ø 150 tube (by

installer'schoice).

7.4

7.2.1

19GB

ELECTRICAL CONNECTION

• Connectthehood to the mains through atwo-poleswitch

having a contact gap of at least 3 mm.

• Openthelighting unit by turning theknobprovided.

• Ensure that the supply cable connector is properly in-

serted into the Suction device socket

Flueassembly

Upper exhaust flue

• Slightly widen the two sides of the upper flue

andhook them behindthe brackets 7.2.1,making

sure that they are well seated.

• Secure the sides to the brackets using the 4

screws 12c (2,9 x 9,5) supplied.

Lower exhaust flue

• Open the two side flaps of the Chimney stack

slightly, hook them between the upper Chimney

stackandthewall,andclose them again until they

fitintoplace,fastening the lower part of the chim-

ney stack into the hood canopy.

12c

7.2.1

2.1

2.2

12c

20GB

USE

Controlpanel

BUTTON LED FUNCTIONS

L- Turns the lighting system on and off.

T1 0/1Motor Fixed Turns the motor on and off.

Flashing 24hExchange

Enabled by pressing and holding the button for approx. 3”.

Provides100 m3/h suctionwitha noise levelofjust 28dB(A).

To disable, press the button again and hold for approx. 3”.

T2 Speed Decreases the working speed.

Flashing Delay (30’)

Pressand hold the button for approx. 2” to enable a 30’ auto-

maticdelayedshutdown.Suitable to complete elimination of

any residual fumes.

T3 Speed Increases the working speed.

T4 Speed Fixed Intensive speed.

Suitableto dealwith maximumvapouremission, thisturns off

automatically ten minutes after starting operation. It can be

disabledby pressing the button T4.

Flashing POWERfunction(maximumsuctionpower)

Press T4 for approximately 3 seconds to enable the Power

function (maximum suction power), which is indicated by

flashingof the LED. This function will be revert to intensive

speed after 5 minutes or when T4 is pressed again.

S1 Led Fixed Signalstriggeringofthe MetalGrease Filterssaturation alarm,

indicating that the filters need washing. The alarm is trig-

gered after the Hood has been operating for 100 working

hours. (Reset see paragraph on Maintenance)

Flashing When enabled, signals triggering of theActivated Charcoal

Filter, which must bereplaced; theMetalGrease Filters must

also be washed. The Activated Charcoal Filter saturation

alarm is triggered after the Hood has been operating for 200

working hours. (Enabling and Reset see paragraph on

Maintenance)

I/P

resetdelay

T1 T2 T3 T4

21GB

REMOTE CONTROL (OPTIONAL)

The appliance can be controlled using a remote

control powered by a 1.5 V carbon-zinc alkaline

batteries of the standard LR03-AAA type.

• Do not place the remote control near to heat

sources.

• Used batteries must be disposed of in the proper

manner.

MAINTENANCE

CleaningtheComfortPanels

• Open the Comfort Panel using the knobs

provided.

• Disconnectthepanel from the hood canopy by

slidingthe fixingpinlever.

• The comfort panel must never be washed in a

dishwasher.

• Cleantheoutsideusingadampcloth andneutral

liquiddetergent.

• Cleantheinside as well using a damp clothand

neutral detergent; do not use wet cloths or

sponges, or jets of water; do not use abrasive

substances.

• Whentheabove operation hasbeencompleted,

hook the panel back to the hood canopy and

close it by turning the knob in the opposite

direction.

22GB

Greasefilters

Alarm signal reset

• Turn the Lights and the suction Motor off, and disable the 24h function if it has been enabled.

• Press T3 for at least 3 seconds, until indicators flash to confirm.

Cleaning the filters

• The filters must be cleaned every 2 months of

operation, or more frequently for particularly

heavyusage,and can be washed in adishwasher.

• OpentheComfortPanelusingtheknobsprovided.

• Removethefilters one at a time bypushingthem

towards the back of the group and pulling down

at the same time.

• Wash theFilterswithout bendingthem,and leave

them to dry thoroughly before replacing. ( The

surface of the filter may change colour after a

time, but this has absolutely no effect on its

efficiency.)

• When refitting the filters, make sure that the

handleisvisibleontheoutside.

• Close the comfort panel.

Activatedcharcoalfilter(Recirculationversion)

• The filter is not washable and cannot be regenerated. It must be replaced when led S1flashes or at

least every 4 months. The alarm signal will only light up when the extractor motor is switched on.

Alarm signal activation

• InRecirculationversion Hoods, the Filter saturation alarmcanbeenabled on installation or atalater

date.

• Turn the Lights and the suction Motor off.

• Press and hold the T3 button for at least 10 seconds, until the LEDs start to flash. Note the number

offlashes:

- 2 flashes of the LEDActivated charcoal filter saturation alarm ENABLED.

- 1 flash of the LEDActivated charcoal filter saturation alarm DISABLED;

This manual suits for next models

Table of contents

Other Küppersbusch Ventilation Hood manuals

Küppersbusch

Küppersbusch KD 9475.0 E Operation manual

Küppersbusch

Küppersbusch KD7580.0GE Operator's manual

Küppersbusch

Küppersbusch DX ISLA User manual

Küppersbusch

Küppersbusch EDIP 6550.0 Quick setup guide

Küppersbusch

Küppersbusch LB 632.0 WG Manual

Küppersbusch

Küppersbusch IKD 954.1 Quick setup guide

Küppersbusch

Küppersbusch LB 6500 Specification sheet

Küppersbusch

Küppersbusch LB6700.0E Quick setup guide

Küppersbusch

Küppersbusch IKD 12450 User manual

Küppersbusch

Küppersbusch EDIP 649.0 Quick setup guide

Küppersbusch

Küppersbusch IKD9885.0 Operator's manual

Küppersbusch

Küppersbusch EMA1008.0E User manual

Küppersbusch

Küppersbusch EDIP 649.1 Quick setup guide

Küppersbusch

Küppersbusch EMA 800.0W User manual

Küppersbusch

Küppersbusch IKD9350.0 Quick setup guide

Küppersbusch

Küppersbusch EDL12700.0GE User manual

Küppersbusch

Küppersbusch DW9320 User manual

Küppersbusch

Küppersbusch IKD9880.0 Quick setup guide

Küppersbusch

Küppersbusch IKD9890.0 Quick setup guide

Küppersbusch

Küppersbusch IKD 11750.0 GE Operation manual

Küppersbusch

Küppersbusch IKD 10770.0 Technical manual

Küppersbusch

Küppersbusch IKD 9375.0 GE User manual

Küppersbusch

Küppersbusch KD 674.1 GE Quick setup guide

Küppersbusch

Küppersbusch KD 646.1 E Operation manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual

Nibe

Nibe S Series Installer manual