Jura IMPRESSA E80 User manual
E8/E80/E800 – Quick Reference Guide
2
E8/E80/E800 – Quick Reference Guide
E8/E80/E800 – Quick Reference Guide
J
These short instructions do not replace the ‘E8/E80/E800 Instruc-
tions for Use’. Make sure you read and observe the safety informa-
tion and warnings first in order to avoid hazards.
You can start coffee system rinsing manually at any time.
TPlace a receptacle under the coffee spout.
TPress the ‘Pc’ button.
TPress the ‘>’ button.
TPress the ‘Rinse the coffee system’ button to start the rinse
operation.
‘Machine is rinsing’, water flows out of the coffee spout. The
operation stops automatically.
After each milk preparation, the E8 prompts you to perform a milk
system rinse.
EIn programming mode, you can set whether the milk system
rinsing is to be prompted 10 minutes after preparation or initi-
ated automatically (see Chapter 4 ‘Permanent settings in pro-
gramming mode – Milk system rinsing’).
EThis chapter applies to the professional fine foam frother and
the fine foam frother.
Precondition:‘Rinse the milk system’ is displayed.
TPlace a receptacle under the fine foam frother.
TPress the ‘Pc’ button.
TPress the ‘>’ button.
TPress the ‘Rinse the milk system’ button to start the rinse
operation.
‘Milk system is being rinsed’ appears and the fine foam
frother is rinsed. The operation stops automatically.
Rinsing the machine
Rinsing the fine foam
frother
3
E8/E80/E800 – Quick Reference Guide
To ensure that the fine foam frother always works properly, you
must clean it daily when you have been preparing milk.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EJURA milk system cleaner is available from specialised dealers.
ETo clean the milk system, use the container supplied.
EThis chapter applies to the professional fine foam frother and
the fine foam frother.
TPress the ‘Pc’ button.
TPress the ‘Clean the milk system’ button.
‘Clean the milk system’
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Clean the milk system’ / ‘Milk system cleaner’
TRemove the milk pipe from the milk container or carton.
TAdd milk system cleaner to the front part of the container
up to the bottom mark (indicated by 6).
TThen fill with water up to the upper mark.
TPlace the container under the fine foam frother.
TConnect the milk pipe to the container.
ETo connect the milk pipe to the container correctly, the pipe
must be fitted with a connector.
TPress the ‘Next’ button.
‘Milk system is being cleaned’ appears and the fine foam
frother and the milk pipe are cleaned.
‘Clean the milk system’ / ‘Fresh water’
TRinse the container thoroughly and fill the front part with
250ml of fresh water.
TPlace this under the fine foam frother and reconnect the
milk pipe to the container.
Cleaning the fine foam
frother
CAUTION
6
6
4
E8/E80/E800 – Quick Reference Guide
TPress the ‘Next’ button.
‘Milk system is being cleaned’ appears and the fine foam
frother and the milk pipe are rinsed with fresh water.
The start screen is displayed.
To make sure the professional fine foam frother works properly, and
in the interests of hygiene, it must be dismantled and rinsed daily if
you have been preparing milk.
TRemove the milk pipe and rinse it thoroughly under running
water.
TRemove the professional fine foam frother.
TDismantle the professional fine foam frother into its individ-
ual parts.
TRinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
TRe-assemble the professional fine foam frother.
EEnsure that all individual parts are correctly and firmly
connected to ensure optimum operation of the professional
fine foam frother.
Dismantling and rinsing
the professional fine
foam frother
1
2
5
E8/E80/E800 – Quick Reference Guide
TRe-fit the professional fine foam frother on the milk system.
To make sure the fine foam frother works properly, and in the inter-
ests of hygiene, it must be dismantled and rinsed daily if you have
been preparing milk.
TRemove the milk pipe and rinse it thoroughly under running
water.
TRemove the fine foam frother.
TDismantle the fine foam frother into its individual parts.
TRinse all the parts under running water. If there are severely
dried-on milk residues, firstly immerse the individual parts
in a solution of 250ml cold water and 1 capful of JURA milk
system cleaner. Then rinse the parts thoroughly.
TRe-assemble the fine foam frother.
EEnsure that all individual parts are correctly and firmly
connected to ensure optimum operation of the fine foam
frother.
Dismantling and rinsing
the fine foam frother
1
2
6
E8/E80/E800 – Quick Reference Guide
TRe-fit the fine foam frother on the milk system.
Your E8 no longer has to be descaled if you are using the CLARIS
Smart filter cartridge.
EOnce the filter cartridge stops working (depending on the
water hardness setting), the E8 will prompt you to change
the filter.
ECLARIS Smart filter cartridges are available from specialised
dealers.
Precondition:The start screen is displayed.
TRemove and empty the water tank.
TFit the filter cartridge extension supplied on top of a new
CLARIS Smart filter cartridge.
TInsert the filter cartridge with its extension into the water
tank.
TTurn the filter cartridge clockwise until it audibly clicks into
place.
TFill the water tank with fresh, cold water and reinsert the
tank.
‘Saved’ appears briefly on the display. The machine has
automatically detected that you have just inserted/changed
the filter cartridge.
‘Filter is beingrinsed’, the water flows directly into the drip
tray.
Rinsing of the filter stops automatically. The start screen is
displayed.
Inserting/changing the
filter
7
E8/E80/E800 – Quick Reference Guide
After 180preparations or 80switch-on rinses, the E8 will prompt you
to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
EThe cleaning programme lasts approximately 20 minutes.
EDo not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
EJURA cleaning tablets are available from specialised dealers.
Precondition:‘Clean machine’ is displayed.
TPress the ‘Pc’ button.
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Empty coffee grounds container’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Clean’
TPlace a receptacle under the coffee spout.
TPress the ‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout.
The operation is interrupted, ‘Add cleaning tablet’.
TOpen the cover of the filler funnel for ground coffee.
TInsert a JURA cleaning tablet into the filler funnel.
TClose the cover of the filler funnel.
TPress the ‘Next’ button.
‘Machine is being cleaned’, water flows out of the coffee
spout several times.
The operation stops automatically.
‘Empty coffee grounds container’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
Cleaning is now complete. The start screen is displayed.
Cleaning the machine
CAUTION
8
E8/E80/E800 – Quick Reference Guide
The E8 builds up deposits of limescale over time and automatically
prompts you to descale it when necessary. The degree of calcifica-
tion depends on the hardness of your water.
EIf you are using a CLARIS Smart filter cartridge, you will not be
prompted to descale.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse off the descaling agent with clean water. Should you get
any descaling agent in your eye, see a doctor.
If the wrong descaling agent is used, the machine could be dam-
aged and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling programme to run to the end.
If the descaling agent comes into contact with sensitive surfaces
(e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
EThe descaling programme lasts approximately 40minutes.
EJURA descaling tablets are available from specialised dealers.
Precondition:‘Decalcify machine’ is displayed.
TPress the ‘Pc’ button.
TPress the ‘Start’ button.
TPress the ‘Next’ button.
‘Empty drip tray’
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Agent in tank’
TRemove and empty the water tank.
Descaling the machine
JCAUTION
CAUTION
CAUTION
CAUTION
9
E8/E80/E800 – Quick Reference Guide
TCompletely dissolve the contents of one blister (3JURA des-
caling tablets) in a receptacle holding 500ml of lukewarm
water. This may take several minutes.
TPour the solution into the empty water tank and insert it into
the machine.
TPlace a receptacle under the fine foam frother.
TPress the ‘Next’ button.
‘Machine is being descaled’ appears and water flows out of
the fine foam frother repeatedly.
The operation is interrupted, ‘Empty drip tray’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
‘Fill water tank’
TRemove the water tank and rinse it thoroughly.
TFill the water tank with fresh, cold water and reinsert the
tank.
TPlace one receptacle under the coffee spout and another
under the fine foam frother.
TPress the ‘Next’ button.
‘Machine is being descaled’, the descaling operation is con-
tinued.
The operation is interrupted, ‘Empty drip tray’.
TEmpty the drip tray and coffee grounds container and put
them back into the machine.
Descaling is now complete. The start screen is displayed.
EIf the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
10
E8/E80/E800 – Quick Reference Guide
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These traces may negatively affect
the coffee result. For this reason clean the bean container from time
to time.
Precondition:‘Fill bean container’ is displayed.
TSwitch the machine off with the On/Off button Q.
TRemove the aroma preservation cover.
TClean the bean container with a soft, dry cloth.
TFill the bean container with coffee beans and close the
aroma preservation cover.
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
TRemove the water tank.
TIf you use a CLARIS Smart filter cartridge, remove this.
TCompletely fill the water tank and dissolve 3 JURA descaling
tablets in it.
TLeave the water tank with the descaling solution for several
hours (e.g. overnight).
TEmpty the water tank and rinse it thoroughly.
TIf you use a CLARIS Smart filter cartridge, insert this again.
TFill the water tank with fresh, cold water and reinsert the
tank.
Cleaning the bean
container
Descaling the water tank
E8/E80/E800_Kurz/en/201806
Other manuals for IMPRESSA E80
3
This manual suits for next models
2
Table of contents
Other Jura Coffee Maker manuals
Jura
Jura GIGA 5 User manual
Jura
Jura Impressa S guide User manual
Jura
Jura ENA Micro 90 User manual
Jura
Jura ENA Micro 5 User manual
Jura
Jura IMPRESSA J5 User manual
Jura
Jura IMPRESSA J5 User manual
Jura
Jura Impressa C9 One Touch User manual
Jura
Jura IMPRESSA X9 User manual
Jura
Jura ENA Micro 9 One Touch User manual
Jura
Jura 760 User manual
Jura
Jura IMPRESSA S9 avantgarde User manual
Jura
Jura X10 User manual
Jura
Jura GIGA 5 User manual
Jura
Jura IMPRESSA A9 One Touch User manual
Jura
Jura ENA 8 User manual
Jura
Jura Giga X3 Professional User manual
Jura
Jura IMPRESSA C9 User manual
Jura
Jura IMPRESSA 601 User manual
Jura
Jura IMPRESSA C5 User manual
Jura
Jura SUBITO User manual
