Jackson Grills PREMIER700-BI User manual

FIRE IT UP WITH JACKSON GRILLS. www.jacksongrills.com

OWNER’S MANUAL for PREMIER700-BI

For Built-in Models:

JPG700BI-LP (Liquid Propane)

JPG700BI-NG (Natural Gas)

Version: SEPT15

Important Notice

Please read ALL safety notices on Pg. 2-3

before assembling or operating this grill.

!WARNING!

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from appliance and

immediately call your gas supplier & fire department.

!WARNING!

1. Do not store or use gasoline or other

flammable liquids in the vicinity of this

appliance.

2. Do not store disconnected propane

tanks in the vicinity of this appliance.

!WARNING!

Failure to follow all manufacturers’

instructions could result in serious

bodily injury and/or property damage.

!SAFETY WARNINGS!

IMPORTANT: Please read and understand all warnings and precautions prior to operating your gas grill.

1 This grill is for outside use only, and shall not be used in any building, garage, enclosed area or vehicle.

2 This grill is set up from the factory for use with Propane Gas (LP). (Propane Cylinder /Tank not included)

3 Do not use gasoline, alcohol or other volatiles for lighting!

4 The Propane (LP) gas supply cylinder must be constructed and marked in accordance with the

specifications for propane gas cylinders of the US Department of transport (DOT) CFR 49 or the National

Standards of Canada, CAN/CSA B339, Cylinders, Spheres and Tubes for the Transportation of

Dangerous Goods.

5 Always open the grill lid slowly & carefully as heat and steam in the grill can cause severe burns.

6 Always place your grill on a hard level surface away from combustible materials

7 Do not attempt to move this grill while lit.

8 Do not leave a lit grill unattended. Keep children and pets away from this grill at all times.

9 Do not use this grill unless it is COMPLETELY assembled and all parts are securely installed.

10 To prevent liquid propane from entering the regulator valve and causing a possible hazard, please ensure

that the propane cylinder is at a lower level than the regulator valve/regulator when in use.

11 Keep grill area clear and free from combustibles and gasoline or other flammable vapors and liquids.

12 Do not alter this grill in any manner.

13 Do not touch any metal surfaces on this grill until it has completely cooled to avoid burns, unless wearing

protective gear. (Pot holders, gloves, BBQ mittens, etc.)

14 It is essential to keep the valve compartment, burners, and circulating air passages clean and free of

obstructions and debris. Inspect the grill before each use.

15 Do not store any spare propane cylinders within 10 feet of this Portable Grill.

16 Please note that propane (LP) is explosive under pressure, heavier than air, and settles and pools in low

areas, which can create an explosion hazard.

17 Contact with propane gas can cause freeze burns to your skin.

18 Dented and rusted propane cylinders may be hazardous and should be checked by a propane gas

supplier, before use.

19 This grill is equipped with a three-prong (grounding) plug for your protection, and should be plugged into

a grounded three-prong receptacle. Do not cut or remove the ground prong.

20 Keep electrical supply cords away from any heated surfaces.

CERTIFICATION & TESTING

This appliance has been tested by Labtest Certification (LC) and has been tested to ANSI Z21.58a-1198 & CGA

16a-M98, and Certified for Canada and the USA.

NOTE: The use and installation of this product must conform to local codes. In the absence of local codes, use the

National Fuel and Gas Code, ANSI A223.1, Storage and Handling of Liquefied Petroleum Gasses, NFPA / ANSI 58.

TABLE OF CONTENTS

Safety Warnings: 3

Certification & Testing; 4

Unpacking Your Grill; Parts Checklist 4

Special Message to Owners: 5

Owner Registration: 5

Tools Required for Assembly: 6

Assembling & Preparing your Grill: 6-7

Installation of a Built-In model 8

Propane Gas Connection: 9-10

Natural Gas Connection 10

Leak Testing: 11

Installer Final Checklist: 12

Fuel Conversions: 12

Lighting Instructions: 13

Grill and Rotisserie Cooking 14-15

Cleaning & Maintenance: 16-18

Storing your Grill: 18

Trouble Shooting: 19

Exploded Parts View: 20

Parts List: 21

Warranty: 22

UNPACKAGING YOUR GRILL

The JPG700BI-2 Built-In Model comes packaged one box. Please open the box carefully and set

aside all loose components. Once unpacked, match the parts to the list shown below. Check

all components for possible damage before assembling your grill. Most of your portable grill

has been factory assembled, however there are still some items that must be unpacked, and

placed in the correct position in your barbecue. For assembly instructions please refer to the

Section, “Assembling & Preparing Your Grill”(Pp.6).

PARTS CHECKLIST:

1 x Main Firebox Assembly

1 x Warming Rack

4 x Flame Diffusers

2 x Cook Grids

1 x Jackson Cover

1 x Grease Cup

1 x AA Battery for Rotisserie Ignition

1 x Complete Rotisserie Kit w/

Flex Light

1 x Owner’s Manual

Propane Models:

1 x Propane (LP) Hose & Regulator

Natural Gas Models:

1 x Natural Gas Hose with Quick Release

!TECH-TIP!

Do not throw away packaging

until you have confirmed that

all parts are present.

!WARNING!

Exercise caution when handling stainless steel; metal edges

may be sharp and can cause injury.

Special Message for our Customers

All of us at Jackson thank you, for choosing a Jackson grill! This appliance was designed, engineered, and built with

quality components and we are confident that it will provide you with years of excellent operation.

Please take the time to read the entire manual and familiarize yourself with all of the features of the Jackson Grill. This

manual also contains important safety information and operation instructions. Please write your barbecue’s serial

number in the space below, and ensure that this manual remains handy to the barbeque for quick reference.

To obtain replacement parts for your Jackson Grill, contact your local dealer. If you have any questions please call us

anytime at the number below: (Please have your model and serial number at hand)

Grill Model: JPG700BI-2

*Serial Number: ________________

*write your serial number here for future reference.

OWNER REGISTRATION: Please take the time to fill out and return a Warranty Registration Card. This can be done

on-line at www.jacksongrills.com, or simply fill in the form below and mail or fax to:

Jackson Grills Fax: 1 (877) 855-5373

#106-2480 Mt. Lehman Rd.

Abbotsford, BC

Canada, V4X 2N3 Customer Service: 1 (888) 287-3333

Please complete and return within 10 days. Thank you.

Title: Mr. Mrs. Ms. Miss (Circle One)

First Name:

Initial:

Last Name:

Street:

Apt. #:

City:

State/Prov.:

Zip/Postal:

Phone:

Email:

Date Purchased:

Dealer:

Model:

Serial #:

Comments:

Thank you for taking the time to fill out this Ownership and Registration Card

Dear Grill Owner; please keep this manual for future reference.

Tools Required for Assembly*:

*Please use the proper tools to simplify installation and prevent personal injury or damage to your grill.

A) Installer Supplied Tools:

1 x Medium Phillips Screwdriver

1 x 5/16” Wrench (or 8mm)

2 x ¾’ Wrench (or 19mm)

Assembling & Preparing Your Grill:

B) Install Flame Diffusers, Cook Grids and Warming Rack:

1. Remove the flame diffusers from the packaging. Please ensure that all protective plastic has been removed.

2. Install the diffusers directly above each burner, by slotting them onto the small pins on the front and rear wall of

the firebox (Fig. 1). Please ensure that the diffusers sit down correctly in their slots, to optimize diffuser function.

3. Install 2 X Cook Grids on the upper ledges of the firebox (Fig. 2)

4. Remove warming rack from packaging and install above cooking grids on the 2 side brackets (or ledges) on

the inner hood.

C) Rear Burner Spark Igniter:

1. Unscrew the plastic/rubber cap from the rear burner ignition module.

2. Insert the supplied AA battery with the positive end facing out. (Fig. 3)

3. Re-install cap.

4. To test the Igniter; push the Igniter button and hold. The ticking noise

from the electrode indicates that the Spark Ignition is working fine!

Figure 1

Figure 3

Figure 2

Figure 4

Figure 6

D) Rotisserie Kit Installation:

1. Slide the Rotisserie Motor onto the Motor Mount Bracket, on the RH

side of the grill (Fig. 4).

2. Side the two forks and the counter balancer onto the spit rod, and

position as desired. Tighten in place.

3. Place the rotisserie rod into the motor. Slide the rotisserie rod bushing over the opposite end of the rod and drop

into the cut-out provided in the RH side of the inner hood (Fig. 5).Once in place, tighten the thumb-screw on the

spit rod bushing.

4. Screw round knob onto end of rotisserie spit rod.

5. Your Rotisserie Kit should look like the Figure 6: you are all ready to cook with your rotisserie!

Line groove up with

cut-out, and drop spit rod

assembly into place.

!TECH-TIP!

Apply anti-seize grease to the threads of

any screw or bolt before reinstalling. This

will greatly simplify future service work.

Figure 5

Installation:

A. Installing in an outdoor cabinet:

This grill must be safely and correctly installed as a built in, before using. Please refer to the chart below, for correct

installation dimensions.

Framing must enclose the grill on the back and sides, but the bottom of the cut-out may be left open. The grill is

supported by the three integral flanges (left, right and rear), so no support underneath is required. NOTE: please

ensure that fuel line openings provide adequate space for the lines,

CABINET FRAMING DIMENSIONS:

Installation in NON-COMBUSTIBLE Cabinets

Width

32 ½”

82.7 cm

Depth (Front to Rear)

18 ½”

45.8 cm

Height (Top to Bottom)

10 ¼”

25.5 cm

Minimum Total Cabinet Depth

24”

61 cm

Rear Clearance to Cabinet

Vertical*

5 ½”

14 cm

Bottom Clearance to Accessory

Doors

3”

7.7 cm

Example of an Installation in

Non-Combustible materials:

cement board and metal studs.

(Grill raised for illustration

purposes).

Figure 7

Propane Gas Connection:

Fuel Source: The following instructions are for a Propane Equipped grill ONLY.

Hose & Regulator: Use only the propane hose and regulator supplied with your Propane grill.

Installation Codes: The installation of this appliance must conform with local codes or, in the absence of local

codes, to the National Fuel Gas Code, ANSI Z223. 1 or CAN/CGA-B149.2 Propane Installation Code.

Propane Cylinder Requirements & Specifications:

1. Maximum Cylinder Size: 20 lbs. (9 Kg)

2. Measurement: (approximately) Diameter: 12’’(30.5cm) X Height: 18” (45.7cm):

3. USA: All LP cylinders used with this grill must be constructed and marked in accordance with the

Specifications for LP (Propane) Gas Cylinders of the US Department of Transportation (D.O.T.). Refer to your

propane cylinder collar for markings.

4. CANADA: All propane cylinders used with this grill must be constructed and marked in accordance with the

National Standard of Canada, CAN/CSA-B339; Cylinders, Spheres and Tubes for the Transportation of

Dangerous Goods and Commission. Refer to your propane cylinder collar for markings.

5. Cylinder supply system must be arranged for vapor withdrawal.

6. Cylinder must be equipped with a collar to protect the outlet valve.

7. Cylinders must be rust and dent free: a dented or rusty propane cylinder may be hazardous, and must be

professionally inspected before use.

8. Cylinders must be equipped with QCC Type 1 (Quick Closing Coupling) outlet, compatible with the regulator

supplied.

9. Propane Cylinders must be equipped with a safety relief valve.

10. UL listed Overfill Protection Device (OPD); This OPD safety feature is identified by a unique triangular hand

wheel. Only use cylinders equipped with this type of valve. (Fig. 8)

Propane Cylinder Handling:

1. Government regulations prohibit shipping full Propane cylinders. You must take your new cylinder to a

Propane filling station for filling.

2. A full cylinder is under high pressure; always handle with care, and transport secured and in an upright

position. Protect the valve from accidental damage.

3. Do not tip the propane cylinder while connecting it to your grill’s regulator

4. If the cylinder is tipped over while connected to your grill, shut it off and disconnect it; then have it checked

before use.

Propane Cylinder Storage:

1. Disconnected propane cylinders must have a dust cap installed for storage purposes.

2. Store all propane cylinders outdoors in a well-ventilated area.

3. Do not store cylinders in direct sunlight or near a source of heat or combustion.

4. Propane cylinders must be REMOVED from your grill; when the grill is to be stored indoors.

5. Keep all propane tanks out of reach of children.

6. If your grill is stored outside, the propane tank may be left connected to the grill. Turn off propane tank valve

when grill is not in use.

Figure 8

Connecting Your Grill to a Propane Cylinder:

1. Make sure tank valve is in its full off position (turn clockwise to stop).

2. Check tank valve to ensure that is equipped with external (male) threads (i.e. QCC-1 type connecter).

3. Make sure all burner knobs are in their off position.

4. Remove the protective dust cap from the cylinder valve. Always reuse dust cap when storing a cylinder.

5. Inspect valve connection port and regulator; look for any damage or debris. Inspect hose for damage. Never

attempt to use damaged or plugged cylinders. Contact your local propane gas dealer for repair.

6. When connecting the regulator to the valve, hand-tighten the black plastic Quick Coupling Connecter (QCC)

nut clockwise to a positive stop. Do not use a wrench to tighten as this may damage the nut and cause leaks.

7. Open tank valve fully (counterclockwise). Use a soapy water solution to check all connections for leaks

before attempting to light grill. If a leak is found, turn tank valve off and do not use grill until a local L.P. gas

dealer can make repairs.

Disconnecting a Propane Cylinder

1. Turn all the grill knobs to off.

2. Turn the tank valve off fully (turn clockwise to stop).

3. Detach the regulator from tank valve by turning the Quick Coupling Connecter (QCC) nut counterclockwise.

4. Install the protective cap back onto the threads of the propane cylinder valve.

Natural Gas Connection:

Fuel Source: The following instructions are for a Natural Gas Equipped grill ONLY.

NG Hose: Use only the natural gas hose supplied with your Propane grill.

Install the Natural Gas Hose supplied, onto the nipple in at the RH wall of the grill cart. The nipple is located on

the bottom of the fuel regulator, and it is a flare nut type connection; DO NOT USE SEALANT of any kind.

Tighten using a ¾” open end wrench.

Attach the supplied female quick release to the home owner’s new or existing Natural Gas Quick Release. This

connection requires Gas Pipe Sealant, or Gas rated Teflon Tape.

Next, double check to ensure that the source gas pressure is no more than 7” water column.

!WARNING!

1 Never insert any foreign objects in valve outlet, as this may cause leaks.

2 Do NOT connect this grill to unregulated Propane systems such as in a

motor home or camper trailer. System pressure MUST be regulated before

hook up.

3 Do NOT use this grill until leak tests have been completed.

4. If a gas leak is detected and cannot be stopped, call the fire department

immediately.

!WARNING!

1 Never insert any foreign objects in the quick release or Natural Gas hose,

as this may cause leaks.

2 Source pressure for Natural Gas MUST be confirmed at 7” Water Column

or less; using a grill at higher pressures could result in property damage,

and injury or death.

3 Do NOT use this grill until leak tests have been completed.

4. If a gas leak is detected and cannot be stopped, call the fire department

immediately.

This manual suits for next models

Table of contents

Other Jackson Grills Grill manuals

Jackson Grills

Jackson Grills JLS550BI-LP User manual

Jackson Grills

Jackson Grills LUX700 User manual

Jackson Grills

Jackson Grills PREMIER 850BI-2 User manual

Jackson Grills

Jackson Grills JLS400-NG User manual

Jackson Grills

Jackson Grills LUX Series User manual

Jackson Grills

Jackson Grills JSS550BI-LP User manual

Jackson Grills

Jackson Grills JENC-LP User manual

Jackson Grills

Jackson Grills JPG50 User manual

Jackson Grills

Jackson Grills LS700BI-LP User manual

Jackson Grills

Jackson Grills JLS700-LP Lux User manual

Jackson Grills

Jackson Grills LUX Built In Series User manual

Jackson Grills

Jackson Grills LUX400 User manual

Jackson Grills

Jackson Grills Premier JPG700 series User manual

Jackson Grills

Jackson Grills Versa 100 JPG100-PKG1 User manual

Jackson Grills

Jackson Grills JLS700-LP Lux User manual

Jackson Grills

Jackson Grills Versa 100 User manual

Jackson Grills

Jackson Grills Keystone Black JKS400BLK-LP User manual

Jackson Grills

Jackson Grills JLS700BI User manual

Jackson Grills

Jackson Grills JLS400 Lux User manual

Jackson Grills

Jackson Grills JSS850BI-LP User manual

Jackson Grills

Jackson Grills JLS400-LP Lux User manual

Jackson Grills

Jackson Grills Classic PG-50403SRL Guide

Jackson Grills

Jackson Grills Patio Fire User manual

Jackson Grills

Jackson Grills JG3 User manual

Popular Grill manuals by other brands

Orbegozo

Orbegozo GR 2300 instruction manual

bora

bora PT11 Operating and installation instructions

Klarstein

Klarstein 10031664 manual

Garland

Garland MWE3W Installation and operation manual

Char-Broil

Char-Broil 463722714 Product guide

Nexgrill

Nexgrill 720-0830HK Operating instruction

Kenmore

Kenmore 415.16123800 Use and care guide

Camp Chef

Camp Chef PG24CLAU Warning & instruction booklet

Tucker Barbecues

Tucker Barbecues GTR Series Assembly, installation and operating instructions

Monogram

Monogram ZGG540NCP1SS owner's manual

Equipex

Equipex Sodir Savoy Operation manual

Gaggenau

Gaggenau VR 414 610 use and care manual

Miele

Miele KM 408-1 operating instructions

George Foreman

George Foreman GGR50B owner's manual

AOG

AOG T series quick start guide

Gorenje

Gorenje TG2000CB Instruction manua

Weber

Weber Genesis Silver-B Permamount NG 051701 owner's guide

Glen

Glen SA 3037 user guide