Iomega ZipCD 650 Instructions for use
Internal ZipCD™ATAPI Drive
PC Quick Install
WRITING
PHONES
DISCIN
OPEN
CLOSE
!
Recordable
ReWritable
650
Start your computer, wait for the operating system to load,
then insert the ZipCD™software disc.
Select “Print Installation Instructions” to view and print detailed
installation instructions. See step 12 for information about viewing the
manual.
Select “Install ZipCD™Software” to install the software needed for your
ZipCD drive. Follow the onscreen instructions.
1
1
2
3
If necessary, change the ZipCD™drive jumper setting 1.
Leave the setting in the Slave 2position if you are connecting the ZipCD™
drive on the same data cable with another device. Use the Master 3setting if
the ZipCD drive will be the only device on the secondary IDE channel. Do
not use Cable Select unless your computer supports this mode. (Check your
computer documentation.)
2
Shut down the computer, disconnect the power cord and
remove cover.
CAUTION! Always turn off power to the computer and all devices
connected to it before beginning any computer hardware change.
NOTE: Locate and write down the drive serial number for your drive.
3
1
WRITING
PHONES
DISCIN
OPEN
CLOSE
Recordable
ReWritable
CD
650
Select the IDE interface connection you want to use.
Connect the ZipCD™drive to the secondary IDE channel 1either in slave
configuration with another drive as master (e.g. CD-ROM) or in master
configuration as the only device. If you are unsure about the connection, see
step 11 to view and print the detailed instructions.
4
5
WRITING
PHONES
DISCIN
OPEN
CLOSE
Recordable
ReWritable
CD
CD
650
650
Locate a vacant 5.25”drive bay. Remove the panel cover and
slide the ZipCD™drive into the drive bay.
Some computers may require rails. Check your documentation.
NOTE: If it makes it easier to connect cables on your computer, you can
secure the ZipCD™drive in the drive bay now. (See step 9.)
6
MASTER
SLAVE
CABLESELECT
AUDIO OUT
RGNDL
CS M
SL A
IDEPIN1
DC INPUT
+5GND+12
ZipCD
PIN 1
Pin 1
40 Pin
Pin 1
Connect the ZipCD™drive to the computer’s IDE connection
using an IDE data cable.
NOTE: You can use either the cable included with the drive or an IDE cable
that may already be connected to the computer’s motherboard.
CAUTION! Make sure PIN 1 on the cable connects to PIN 1 on the ZipCD™
drive, the motherboard, and any other connected device.
MASTER
SLAVE
CABLE SELECT
AUDIO OUT
R GND L
C S M
S L A
IDE PIN1
DC INPUT
+5 GND +12
Skip this step if the computer’s CD-ROM drive is already
connected to the computer’s audio in port.
Connect the audio cable to the ZipCD™drive and the computer’s audio
connector, usually located on the sound card or the motherboard. Check
your sound card documentation or your system’s documentaton and the
User’s Manual for more detailed instructions.
7
MASTER
SLAVE
CABLE SELECT
AUDIO OUT
R GND L
C S M
S L A
IDE PIN1
DC INPUT
+5 GND +12
Connect a computer power supply cable.
You may need a Y-cable if your system’s power cable does not have a free
connector.
CAUTION! Make sure the power supply cable is securely connected to the
ZipCD™drive.
8
Other Iomega Storage manuals
Iomega
Iomega eGo Encrypt User manual
Iomega
Iomega eGo 34491 User manual
Iomega
Iomega ALPHA 10H Parts list manual
Iomega
Iomega 33115 User manual
Iomega
Iomega StorCenter ix-Series User manual
Iomega
Iomega 34172 User manual
Iomega
Iomega Ultramax 34389 User manual
Iomega
Iomega EN55022 User manual
Iomega
Iomega Prestige 34807 User manual
Iomega
Iomega UltraMax Pro User manual
Iomega
Iomega PocketZip Instructions for use
Iomega
Iomega eGo 34895 User manual
Iomega
Iomega REV 35gb Assembly Instructions
Iomega
Iomega eGo 34898 User manual
Iomega
Iomega HDD User manual
Iomega
Iomega 33904 User manual
Iomega
Iomega TAPE250 User manual
Iomega
Iomega eGo 34985 User manual
Iomega
Iomega Media Xporter 33992 User manual
Iomega
Iomega StorCenter px2-300d User manual
