InFocus LASER PROJECTOR LP 540 Guide

Replacing the projection lamp

The lamp hour timer in the About menu counts the number of hours the

lamp has been in use. Fifty hours before the specified end of the lamp’s life,

the message “Replace lamp” briefly appears on the screen at each startup

and in the Interactive Display. After 50 additional hours, the lamp will no

longer light. You can order new lamp modules from your dealer. See

“Accessories” on page 41 for information.

1Turn off the projector and unplug the power cable.

2Wait 60 minutes to allow the projector to cool thoroughly.

3Turn the projector upside down and remove the lamp door by loosening

the captive screw and then prying the lamp door out.

4Remove the two screws on the lamp module.

WARNINGS:

• To avoid burns, allow the projector to cool for at least 60 minutes before

you replace the lamp.

• Unplug the power cord before replacing the lamp.

• Do not drop the lamp module. The glass may shatter and cause injury.

• Do not touch the glass lamp screen. Fingerprints can obscure projection

sharpness.

About menu

computer 2 network

monitor out

audioout

audioin

audio in

serial control

computer in

computer 1

video 2

video in

RS-video 1

turn off and unplug

the projector

wait 60 minutes

loosen the screw on lamp door pry the lamp door off

remove the screws on lamp module

• Be extremely careful when removing the lamp housing. In the unlikely

event that the lamp ruptures, small glass fragments may be generated.

The lamp module is designed to contain most of these fragments, but

use caution when removing it. Before replacing the lamp, clean the

lamp compartment and dispose of cleaning materials. Wash hands after

lamp replacement. his product has a lamp which contains a very small

amount of mercury. Dispose of it as required by local, state or federal

ordinances and regulations. For more information see www.eiae.org.

5Carefully remove the lamp module by grasping and lifting the metal

bail wire. Dispose of the lamp in an environmentally proper manner.

6Install the new lamp module, making sure that it is properly seated.

7Replace the two screws.

8Replace the lamp door and tighten the screw.

9Plug in the power cable then press the Power button to turn the projec-

tor back on.

10 Reset the lamp hour timer.

Resetting the lamp timer

If the lamp timer has reached the maximum number of hours for the projec-

tor lamp, the LED on the projector’s keypad will show a lamp error (see

“LED behavior and meaning” on page 16). To reset the lamp timer, press the

decrease volume button on the remote and then the increase volume button

within 3 seconds. At that point the LED will turn green and you can power

on the projector. You can also navigate to the Settings>Service menu and

select Lamp Reset to reset the lamp timer.

remove module using bail wire

reset lamp time in Service menu

Other manuals for LASER PROJECTOR LP 540

This manual suits for next models

Table of contents

Other InFocus Projector Accessories manuals

InFocus

InFocus LP130 Guide

InFocus

InFocus SP-CEIL-010 User manual

InFocus

InFocus LiteProLS User manual

InFocus

InFocus LP70+ Guide

InFocus

InFocus LITESHOW4 DB+ User manual

InFocus

InFocus RPM A-C User manual

InFocus

InFocus SP-LAMP-088 Guide

InFocus

InFocus IN2112 Guide

InFocus

InFocus CableWizard SP-CW3 Quick start guide

InFocus

InFocus LP630 User manual

InFocus

InFocus SP-LAMP-080 Guide

InFocus

InFocus CEILING MOUNT LP 1000 SERIES User manual

InFocus

InFocus IN42 Guide

InFocus

InFocus LP770 User manual

InFocus

InFocus LP790 User manual

InFocus

InFocus LiteShow network adapter User manual

InFocus

InFocus LiteShow 4 DB+ User manual

InFocus

InFocus LNS-W01 Guide

InFocus

InFocus SP-LAMP-073 Guide

InFocus

InFocus SP-LAMP-092 Guide

InFocus

InFocus SP-CEIL-006 User manual

InFocus

InFocus SP-CEIL-012 User manual

InFocus

InFocus SP-CEIL-008 User manual

InFocus

InFocus SP-LAMP-086 Guide

Popular Projector Accessories manuals by other brands

Optoma

Optoma BX-AL133B datasheet

PEERLESS

PEERLESS PE 1120 Installation and assembly

Osram

Osram SIRIUS HRI Series Directions for use

Presentation Switchers

Presentation Switchers PS111 quick start

Kramer

Kramer VIA GO user manual

Yamaha

Yamaha PJL-112 Replacement guide

Swedstyle

Swedstyle CL23AA02ZA25E operating manual

Mitsubishi Electric

Mitsubishi Electric 236CB Features

Epson

Epson BrightLink 475Wi user guide

Acer

Acer WP100 quick guide

i3 i3board user manual

CHIEF

CHIEF HB-43E installation instructions

Biamp

Biamp Modena Hub Network administrator's guide

NEC

NEC MP10RX Quick setup guide

Panamorph

Panamorph DCR-S3 installation guide

Exact solutions

Exact solutions FRAME-EVO-P10 manual

CHIEF

CHIEF VCM103S installation instructions

Sharp

Sharp AN-PH20EZ Operation manual